• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.1
• /
• pp.81-88
• /
• 2014

An experimental study is performed to obtain an average heat transfer coefficient around the perimeter of a near horizontal tube. For the test a stainless steel tube of 50.8 mm diameter submerged in water at atmospheric pressure is used. Both subcooled and saturated pool boiling conditions are considered and the inclination angle of the tube is changed from the horizontal position to $9^{\circ}$ in steps of $3^{\circ}$. In saturated water, the local boiling heat transfer coefficient at the azimuthal angle of $90^{\circ}$ from the tube bottom can be regarded as the average of the coefficients regardless of the tube inclination angles. However, when the water is subcooled the location for the average heat transfer coefficient depends on the inclination angle and the heat flux. It is explained that the major mechanisms changing the heat transfer are closely related with the intensity of the liquid agitation and the generation of big size bubbles through bubble coalescence.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.1
• /
• pp.21-31
• /
• 2018

This paper analyzes the displacements of CFRD which was completed by field measurement. It is to understand the deformation behavior of the dam body according to the water level change from the impounding time. And it was compared with numerical analysis results. As a result of measuring the behavior of the dam crest and downstream slope according to impounding, horizontal displacements in axis direction of the dam, upstream and downstream displacements and settlements occurred mostly when the water level reaches about half of the dam height. The displacements continued until the water level reached its maximum. After that, it showed a constant convergence regardless of the water level. Horizontal displacements of the face slab which is the most important in CFRD were similar at all locations. The Horizontal displacements of the face slab showed the trends of increasing in winter and decreasing in summer due to the effect of the outside temperature before impounding. Also, the displacements increased until the water level reached about half of the dam height. After that, they decreased with rising in water level. As a result, the face slab behaviors according to seasonal change after impounding as well as water level condition. It is judged because of the material characteristics of the concrete slab. Numerical analysis showed slightly different maximum settlement and depth of occurrence from the measuring data after construction of the dam. It is considered that this is due to various design and construction differences such as the estimation of input parameters in analysis, construction period, and the layer thickness of construction. For the overall period of the dam, the settlements were mostly completed during the construction period and some settlements occurred in the early days of impounding and then converged.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.30 no.4
• /
• pp.339-349
• /
• 2014

If the maxillomandibular relationship is unstable or requires treatment for improved function and esthetics, the first treatment objective is to provide stable occlusal contacts. The patient has moderate mental retardation. Due to inadequate vertical overjet, horizontal arch malrelation and excessive tooth loss, full mouth rehabilitation was required. The purpose of treatment planning is to establish physiologic maxillomandibular relation. Using cephalometrics for occlusal analysis is an aid to make a decision. The amount of horizontal bone reduction was calculated with evaluating soft tissue profile. After provisional denture placement, healing of the surgical site and newly adapted arch relationship was evaluated. The patient satisfied with esthetics and showed stable holding contacts. Periodic examination is needed to exclude occlusal disharmony.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.5
• /
• pp.21-30
• /
• 2019

While the study of the shallow tunnel has been mainly on the longitudinal load transfer and horizontal surface conditions, the study of the ground behavior of shallow tunnel under the slope is not sufficient. Therefore, in this study on the ground behavior around a tunnel due to the sidewall deformation of shallow tunnel under the slope that is excavated in longitudinal direction, a scale-down model test has been performed. The model tunnel has the dimension of 320 mm wide, 210 mm high and 55 mm long with enough material strength in aluminum and the model ground has the uniform ground conditions by 3 types of carbon rods. The model test has been performed with the variables of slopes and the cover depths by controlling the tunnel sidewall deformation, and the change of sidewall-load, load transfer, ground subsidence was monitored and analyzed. According to the increase of the slope, the maximum ground subsidence increased by 20~39% compared to the horizontal surface. The load ratio increased by maximum 20% in the tunnel crown and decreased in sidewall according to the surface slope. The load transfer shows maximum 128% of increase at the cover depth of 1.0D, while at the 1.5D cover depth it shows non-critical difference from horizontal surface. The slope has major effects on load transfer at the cover depth of 1.0D.

• The korean journal of orthodontics
• /
• v.27 no.3 s.62
• /
• pp.431-444
• /
• 1997

This research was carried out to compares the treatment effects of Horizontal and Vertical type activators in Angle's Class II div. 1 maloccusion patients with mandibular retrusion dand to find out whether different treatment effects or growth pattern were observed between sexes in each study groups. The results were as follows: 1. In Horizontal activator group, forward positioning of mandible and vertical increase in anteror face as examplified by increase of LAFH and AEM were observed when pre and post-treatment datas were evaluated. 2. Males samples in Horizontal activator group showed increase in mandiular length accmpanied by posterior positioning of maxilla, wheras female samples in Horizontal activator group showed increase in mandibular body length, labial inclination of mandibular incisors and increase in lower anterior facial height .3. In vertical activator group, increase in AFH, LAFH, PFH and LPFH were observed when pre and post treatment datas were evaluated. 4. Male samples in Vertical activator group showed increase in mandibular body length and anterior and posterior facial heights, whereas females samples of Vertical activator group showed mainly increase in anterior facial height. 5. When pre and post treatment datas of Horizontal and Vertical activator groups were compared, skeletal difference were mainly observed in pretreatment datas but dental difference were observed in post treatment datas ,indicating that two actiators differ only in their effects to dental variables. 6. Difference between sexes were noted after treatment although no difference were observed between sexs in each groups before treatmentt. This indicates that inherent growth effects in each sex exerts more influence 1km appliances used for treatment.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.1
• /
• pp.18-27
• /
• 1996

Efforts are concentrated onto effective simulation of surface discharged heat water in two-dimensional depth-averaged finite element model using Gaussian puff algorithm incorporating near-field characteristics as patches computed from CORMIX3 with ambient flow variations. Concise analyses of horizontal and vertical temperature distributions are made for real coastal power plant discharges through four field observations and the results from this proposed method are in good agreements with observations in far-field as well as near-field. Thus, this method can simulate the heat dispersion effectively for the whole region since the complex jet momentum characteristics and ambient flows are easily represented in 10 meters of finite element discretization around a discharging point.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.2
• /
• pp.191-199
• /
• 1993

Diffusion of a steady horizontal line source in a turbulent shear flow is simulated by numerically solving a steady two-dimensional advective diffusion equation. The computational result is compared with the analytic solution for uniform velocity and diffusivity distributions over the depth. The analytic solution for constant velocity and diffusivity overestimates the degree of vertical mixing. The normalized equation indicates that friction factor is the only physical parameter that governs the vertical diffusion process. Sensitivities of the diffusion process to the friction factor and initial source position are analyzed. The rate of vertical mixing varies approximately as the square root of the friction factor. The optimal source position, which gives the most rapid mixing, lies above the mid-depth and moves toward the water surface as the friction factor increases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.11
• /
• pp.964-972
• /
• 2007

Wind turbine experiment was carried out for the horizontal axis wind turbine with the aerodynamically optimized blade. From the comparison of aerodynamic performance between upwind and downwind type wind turbine rotor, the measured torque fluctuation of the latter is larger than that of the former. This phenomenon is owing to the interaction of wake generated from support column and blades. The wind turbine model satisfies the design condition in that the measured result of the power coefficient at zero pitch angle shows maximum peak at the designed tip speed ratio, λ = 6. It also shows that the decrease in aerodynamic power due to negative pitch change is more sensitive than that of the same positive pitch change.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.2
• /
• pp.263-272
• /
• 1994

The purpose of this study was to identify factors that might distinguish those who have a high level of Intention to purchase each of domestic, foreign designer and national brand jeans from those who have a low intention in terms of evaluative criteria belief, ideal jeans image and clothing altitude. The sample consisted of 198 male and 197 female students from five universities in Seoul. The questionnnaire consisted of 50 seven-point semantic differential scales dealing with evaluative criteria and ideal jeans image, beliefs about and intention to purchase domestic, foreign designer and foreign national brand jeans and 25 Likert type clothing attitude scales. Based on a series of t-tests the results showed that color and design were the most influencing factor among the evaluative criteria belief, regardless of brand type, while durability, accessory, sewing were the least. Sexy image, brand consciousnees and fashion interest were the important factor that distinguish high intention to purchase group fro)m low intention to purchase group.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.4
• /
• pp.415-421
• /
• 2015

This paper describes the study of the design procedure for the step-by-step setup parameters and of the magnetizing method for performance and size reduction in the development of a haptic vibrator. The study of magnetization was accomplished by comparing the electromagnetic force in accordance with the horizontal and the vertical magnetization. The theoretical results indicated that the horizontal magnetization resulted in a better performance. The systematic design of a step-by-step procedure for establishing the design parameters was verified by testing the characteristics of the fabricated prototype product. The vibration response function analysis and electric field analysis were processed by decoupling of the analytical method, and these were determined to be in good agreement with the test results. The design parameters to contributing to the product reliability included the spring height, the welding position, and the coil position. The sensitivity of the electromagnetic field and the performance change were analyzed based on the design parameters. As a result, we proposed a design method to implement a reliability-based, high performance haptic vibrator.