• Applied Chemistry for Engineering
• /
• v.10 no.5
• /
• pp.778-783
• /
• 1999

The effect of carbon fiber orientation on the tribological properties of carbon fiber/epoxy composites used as a reflecting material for the electromagnetic wave has been investigated. It was found that the carbon fiber/epoxy composite which slides normal to prepreg lay-up direction had less friction and wear that those slides parallel to prepreg fiber lay-up direction due to the increase of delamination between carbon fiber and epoxy. Composite with unidirectional orientation($0/0^{\circ}$) had higher tribological properties than those with multidirectional orientation($0/45/90/-45^{\circ}$ and $0/90^{\circ}$) when the sliding direction was normal to prepreg lay-up direction. This was caused by the debonding between carbon fiber and epoxy which is proportional to contact area between the sliding surface and carbon fiber. Opposite results have been found when the sliding direction was parallel to prepreg lay-up direction due tot he tensile force applied on carbon fiber. In addition, it was shown that wear factor increased with increasing sliding velocity but the friction coefficient did not depend upon the sliding velocity.

• Journal of the Korean Ceramic Society
• /
• v.39 no.8
• /
• pp.758-763
• /
• 2002

The various ultrasonic energies (28 kHz, 40 kHz, 70 kHz) were used to improve the magnetic properties of Ba-ferrite as the perpendicular magnetic recording materials. In the sheet formation process, the different orientation hars were used to orientate perpendicularly the dispersed Ba-ferrite to sheet. Throughout these experiments, we have obtained relatively higher value of S. Q. (Squreness Ratio : 0.783) and O. R. (Orientation Ratio : 2.87) magnetic properties at 2 h ultrasonic treatment of 40 kHz ultrasonic energy. With aid of SEM(Scanning Electron Microscopy) images, the obtained sheet with dispersed of Ba-ferrite could be used for perpendicular magnetic recording due to orientated to easy magnetization axis, c-axis. In addition, the value of S. Q. of sheet decreased with increasing applied magnetic field angle during measuring of S. Q. value with changing applied magnetic field angle by VSM (Vibrating Sample Magnetrometer). This result also induced the probability for prependicular magnetic recording.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.770-775
• /
• 2000

A new photo-polymer material of the copoly (PM4Ch-ChMA), copoly (poly (4-methacryloyloxy)chalcone-cholesteryl methacrylate) for homeotropic alignment was synthesized and the electro-optical (EO) performance for the photo-aligned vertical-aligned (VA)-LC display (LCD) was studied. Good thermal stabilities of synthesized copolymer were obtained by TGA(Thermogravimetric Analysis) measurement. Good voltage-transmittance (V-T) and response time characteristics for the photo-aligned VA-LCD with polarized UV exposure in oblique direction($\theta$$_{i}$=30$^{\circ}$) on a copolymer-1 (2%) surfaces for 1 min were observed. but, light leakage in the off-state was observed. Therefore, we achieved excellent V-T and response time characteristics for the photo-aligned VA-LCD with UV exposure on a copolymer-3 (30%) surfaces for 3 min.n.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.393-398
• /
• 2007

We studied the mechanism of liquid crystal alignment on polyvinylfluorocinnamate (PVCN-F) films which were irradiated by UV using polarized fourier transform infrared (FT-IR) spectroscopy and ultraviolet/visible (UV/Vis) spectroscopy. UV irradiation of PVCN-F films caused decrease of vinylene -C=C- stretching peak area at $1638cm^{-1}$ and shift of conjugated C:0 stretching vibration at $1712cm^{-1}\;to\;1734cm^{-1}$ which is caused by nonconjugated C=O stretching nitration. To study the orientation direction of 5CB liquid crystal (LC) molecules in the liquid crystal cell with PUV irradiation, rubbing treatment or without any treatment on the PVCN-F alignment layer, we used polarized FT-IR dichroism technique. We successfully measured 5CB LC alignment directions, which are perpendicular to the irradiated PUV polarization direction and parallel to the rubbing direction in the liquid crystal cell without using dichroic dyes.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.260-260
• /
• 2009

탄소나노튜브 (carbon nanotube, CNT)는 우수한 전기적, 화학적, 기계적 성질과 큰 비표면적인 구조적인 특성에 기인하여 전자방출원 수직 소자에서의 interconnection, 에너지 저장 소자에서의 전극재료 및 고감도센서 등 다양한 분야로의 응용이 예상되고 있다 [1]. 본 연구에서는 이러한 응용을 위한 계면제어 측면제어 측면에서, 고전도성을 확보하기 위하여 금속 기판 위에 수직배향 탄소나노튜브(VCNT)를 직접 성장시키고자 하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.2
• /
• pp.152-158
• /
• 2000

The crystallographic grain orientation of {{{{ { ZrB}_{2 } }}}}-ZrC composite sintered by pressureless a sintering(PLS) and spark plasma sintering (SPS) was analysed by the SEM-EBSP technique. In the case of PLS, (160) plane of {{{{ { ZrB}_{2 } }}}} was oriented to ND direction, (101) and (111) plane of ZrC were oriented to ND direction. In the case of SPS, (0001) plane of {{{{ { ZrB}_{2 } }}}} was strongly oriented to ND direction. Only (001) plane of ZrC was oriented to ND direction. The PLS specimen had weakly oriented grain structure and interface between {{{{ { ZrB}_{2 } }}}} and ZrC was found to be more stable than that of SPS but the SPS specimen had a preferentially oriented grain structure.

• Polymer Science and Technology
• /
• v.21 no.3
• /
• pp.236-240
• /
• 2010

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.255.2-255.2
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.07a
• /
• pp.180-181
• /
• 2004

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.249-250
• /
• 2007