• Explosives and Blasting
• /
• v.36 no.2
• /
• pp.27-35
• /
• 2018

This study introduces a suggested underwater blasting method in contrast with conventional underwater blasting methods which adopt the drilling and charging procedures by divers. A structural underwater charging system makes it possible to drill into underwater bedrock and charge explosives on the deck of barge ship. The applicability and effectiveness of the suggested method was experimentally approved by comparing with a kind of underwater charging system as a conventional underwater blasting method.

• Explosives and Blasting
• /
• v.20 no.1
• /
• pp.67-75
• /
• 2002

수중수로관통 발파는 수로터널을 호수 바닥에 근접하도록 터널을 뚫고 최종적으로 플러그를 발파하여 수로와 호수 바닥을 연결시키는 발파 기술로서 수력발전에서 경비와 공기를 단축시킬 수 있는 매우 유용한 기술이다. 이 기술은 본질적으로는 수중발파와 동일하지만 완벽한 성공을 보장하기 위한 별도의 조치를 해야하고 수갱의 수문과 여타의 설비를 보전할 수 있는 대책을 강구하여야 한다. 논문에서는 노르웨이에서는 보편화되어 있는 이 기술의 핵심 내용과 적용의 예를 실어 소개하고자 한다.

• Explosives and Blasting
• /
• v.22 no.3
• /
• pp.57-64
• /
• 2004

There are two major types of underwater blasting at Korea, bridges and harbor construction work. Pier blasting for lay the foundation bridges construction is used dry excavation working (drilling and charging) after pump out water and then fire pump in water that is same as bench blasting. In contrast, underwater blasting for harbor construction and increase of harbor load depth is used to barge with digging equipment that is in oder to drilling on the surface and blasting work(charge, hook-up) under water. Thus, there are need to special concern such as charge method and hook-up method different from tunnel blasting work and bench blasting work. If do not use special concern breaks out dead pressure and mis fire because of there are so many difficult condition such as water pressure, obstruct field of vision. In this study underwater blasting at Busan Harbor Construction have consider with special concern that is plastic pipe charge method used to MegaMITE I and specialized buoy hook- up method make far initial system detonate on the surface used to TLD. The results is designed blast pattern charge per delay effect an inspection of verify between predict velocity and measure velocity. minimized break out mis fire consideration charge method, hook up method. According to result best underwater blasting design is 105mm drilling dia, MeGAMITE II, HiNLL Plus(non electric detonator).

• Explosives and Blasting
• /
• v.25 no.2
• /
• pp.71-78
• /
• 2007

In many cases of underwater blasting in South Korea, the special blasting is mainly used for deepening harbor, installing gas pipes, or well blasting to build a bridge. The procedure of well blasting is almost same with shaft blasting, but the difference is that water is filled in before blasting. In case of deepening blasting under water, the first step like drilling, arranging explosives, and wire connection is done on a barge, then the next step such as charging and tamping is accomplished under water by expert divers. Therefore, underwater blasting needs precise and exact plan before blasting. In this paper, authors would like to introduce a case of underwater blasting for deepening the Busan new port with emulsion explosives and non-electric detonators in order to get some of 8,500TEU out sized container vessels entered into the port and to make safe. Considering environment and vibration, the blasting was controlled to minimized the damage to the lighthouse nearby. It will be great help to many other blasting sites where emulsion explosives and non-electric detonators are used for underwater blasting through this case.

• Explosives and Blasting
• /
• v.29 no.2
• /
• pp.81-88
• /
• 2011

Most of the blast pollution that causes complaints is noise and vibration. Hence, special attentions need to be paid to controlling the underwater noise in designing blasting for those areas. This study estimated underwater sound pressure using distance from blasting and charge per delay and underwater sound pressure level using the underwater sound pressure. To identify the validity of the estimated value, the study demonstrated the results at other areas and compared actual results with estimated results.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.5
• /
• pp.47-54
• /
• 2008

In this study, ground vibration values and damping coefficient produced by underwater blasting were measured and analyzed. Equations of vibration, $V=K(SD)^{-0.536}$, were presented from quantitative experiment results. The K Values are classified with 1.507, 2.005 and 2.939 respectively at 50%, 90% and 95% reliability. Also, hydrospace noise in aquafarm and noise in atmosphere as well as ground vibrations were measured, and maximum values of these results were 86.8dB(A), 147.8dB(A), 0.244cm/s, respectively. Equations of hydrospace noise, $SL=293.2SD^{-0.164}$, was presented from quantitative experiment results. Also, the flow-chart for influence estimation and underwater blast design was presented from these results. The results of the study may be applied for the evaluation of the influence on aquafarm as a basic data before having main underwater blasting at construction sites.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.578-592
• /
• 2021

This study performed to investigate the propagation characteristics of overpressure, impulse, vibration in underwater blasting. The difference between air blasting and underwater blasting is that noise and vibration propagate through water as a medium. In some cases, the noise and vibration propagates through various media (rock, water, air, etc.). In this study, the underwater blasting was simulated using AUTODYN, and the propagation characteristics of overpressure, impulse and vibration induced by blasting were analyzed. We mainly focused on the effect of mesh size on the overpressure, impulse and peak particle velocity from the underwater blasting simulation. The numerical results indicated that the overpressure and peak particle velocity tended to decrease as the mesh size increased, while the impulse increased with the mesh size. The results also indicated that the mesh dependence varied depending on the explosive charge and scaled distance.

• Explosives and Blasting
• /
• v.28 no.2
• /
• pp.28-36
• /
• 2010

A study about economical blasting methods which can improve fragmentation and save explosive in blasting is in progress. One of the blasting methods is an air decking method making air layers in boreholes. However, it is difficult to apply this method to the boreholes filled with water. In this study, an underwater Air Tube was manufactured and tried to place it at a certain location in a water filled borehole. It was found that the application of underwater air tube in wet boreholes could improve the fragmentation and save 10~15% of the explosives.

• Proceedings of the KSEE Conference
• /
• 2004.08a
• /
• pp.97-126
• /
• 2004

• Proceedings of the KSEE Conference
• /
• 2008.04a
• /
• pp.135-144
• /
• 2008