• Korean Journal of Ecology and Environment
• /
• v.40 no.2
• /
• pp.201-213
• /
• 2007

In this study, the Batter Assessment Science Integrating point and Nonpoint Sources (BASINS 3.0)/window interface to Hydrological Simulation Program-FPRTRAN (WinHSPF) was applied for assessment of Soyang Dam watershed. WinHSPF calibration was performed using monitoring data from 2000 to 2004 to simulate stream flow. Water quality (water temperature, DO, BOD, nitrate, total organic nitrogen, total nitrogen, total organic phosphorus and total phosphorus) was calibrated. Calibration results for dry-days and wet-days simulation were reasonably matched with observed data in stream flow, temperature, DO, BOD and nutrient simulation. Some deviation in the model results were caused by the lack of measured watershed data, hydraulic structure data and meteorological data. It was found that most of pollutant loading was contributed by nonpoint source pollution showing about $98.6%{\sim}99.0%$. The WinHSPF BMPRAC was applied to evaluate the water quality improvement. These scenarios included constructed wetland for controlling nonpoint source poilution and wet detention pond. The results illustrated that reasonably reduced pollutant loadin. Overall, BASINS/WinHSPF was found to be applicable and can be a powerful tool in pollutant loading and BMP efficiency estimation from the watershed.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2008.11a
• /
• pp.428-432
• /
• 2008

대수층의 저유량이 풍부한 강변여과수 개발 예정지역의 충적충(지표면하 25$\sim$35 m 구간)에서 수리전도도와 증분산지수의 규모종속효과를 규명하기 위해 양수시험과 수렴흐름 추적자시험이 수행되었다. 양수시험과 추적자시험의 규모는 2 m 와 5 m 이었으며 양수시험은 5개 공, 추적자시험은 3개 공을 이용하여 수행되었다. 양수시험은 일정한 양수율(2,500 m$^3$/day)로 수행되었으며, 양수 시작 후 경과시간에 따른 수위변화 자료를 AQTESOLV 3.5 프로그램에 입력하여 해석하였다. 시험대수층의 수리전도도는 양수정에서 1.745$\times$10$^{-3}$ m/sec, 양수정에서 이격거리가 2 m 구간에서는 2.161$\times$10$^{-3}$ m/sec와 2.270$\times$10$^{-3}$ m/sec 이었으며, 이격거리가 5 m 구간에서는 2.452$\times$10$^{-3}$ m/sec와 2.591$\times$10$^{-3}$ m/sec로 산정되었다. 그리고, 양수정에서 회복시험 시 Theis(Recovery) 방법에 의해 해석된 수리전도도는 1.603$\times$10$^{-3}$ m/sec이었다. 양수정에서 관측정의 이격거리(d)에 따른 수리전도도(K) 증가함수는 log K = 0.0693logd-2.071와 log K = 0.08171og d-2.655로 추정되었으며, 결정계수는 각각 0.965와 0.979로서 매우 높게 나타났다. 따라서 양수정에서의 이격거리가 멀수록 수리전도도가 증가하는 규모종속을 확인하였으며, 또한 시험대수층의 수리전도도가 방사상으로 유사하게 분포하고 있음을 알 수 있었다. 수렴흐름 추적자시험의 양수율은 2,500 m$^3$/day 이었으며, 2개의 주입정에 염소이온 5 kg을 순간 주입하였다. 염소이온의 농도이력곡선을 작성하여 초기도달시간과 최고농도의 차이를 분석하였으며, 누적질량회수곡선을 통해 양수 후 경과시간에 따른 염소이온의 질량회수율을 분석하였다. 그리고, 염소이온농도 대 누적질량회수율의 이력그래프를 작성하여 누적질량회수율에 따른 염소이온농도의 증가와 감소 변화를 분석하였다. 또한, 염소이온농도의 증가/감소 구간에 대한 선형회귀분석을 수행하여 농도 증가율과 감소율의 변화를 파악하였다. 양수정에서 관측된 경과시간별 염소이온농도 자료를 CATTI 코드의 "Converging Radial Flow With Instantaneous Injection" 해석법에 적용하여 종분산지수를 추정하였다. 양수정에서 이격거리가 2 m인 경우의 종분산지수는 0.4152 m, 이격거리가 5 m인 경우의 종분산지수는 3.2665 m 이었다. 따라서 양수정에서 이격거리가 멀수록 종분산지수가 증가하는 규모종속효과를 확인하였으며, 또한 이격거리에 대한 종분산지수의 비는 각각 0.21과 0.65 정도로서 증가하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.1899-1903
• /
• 2008

대수층의 저유량이 풍부한 강변여과수 개발 예정지역의 충적층(지표면하 $25{\sim}35\;m$ 구간)에서 수리전도도와 종분산지수의 규모종속효과를 규명하기 위해 양수시험과 수렴흐름 추적자시험이 수행 되었다. 양수시험과 추적자시험의 규모는 2 m 와 5 m 이었으며 양수시험은 5개 공, 추적자시험은 3개 공을 이용하여 수행되었다. 양수시험은 일정한 양수율($2,500\;m^3/day$)로 수행되었으며, 양수 시작 후 경과시간에 따른 수위변화 자료를 AQTESOLV 3.5 프로그램에 입력하여 해석하였다. 시험 대수층의 수리전도도는 양수정에서 $1.745{\times}10^{-3}\;m/sec$, 양수정에서 이격거리가 2 m 구간에서는 $2.161{\times}10^{-3}\;m/sec$와 $2.270{\times}10^{-3}\;m/sec$ 이었으며, 이격거리가 5 m 구간에서는 $2.452{\times}10^{-3}\;m/sec$와 $2.591{\time}10^{-3}m/sec$로 산정되었다. 그리고, 양수정에서 회복시험 시 Theis(Recovery) 방법에 의해 해석된 수리전도도는 $1.603{\times}10^{-3}\;m/sec$이었다. 양수정에서 관측정의 이격거리(d)에 따른 수리전도도(K) 증가함수는 log K=0.0693 log d-2.671와 log K=0.0817 log d-2.655로 추정되었으며, 결정 계수는 각각 0.965와 0.979로서 매우 높게 나타났다. 따라서 양수정에서의 이격거리가 멀수록 수리전도도가 증가하는 규모종속을 확인하였으며, 또한 시험대수층의 수리전도도가 방사상으로 유사하게 분포하고 있음을 알 수 있었다. 수렴흐름 추적자시험의 양수율은 $2,500\;m^3/day$ 이었으며, 2개의 주입정에 염소이온 5 kg을 순간 주입하였다. 염소이온의 농도이력곡선을 작성하여 초기도달시간과 최고농도의 차이를 분석하였으며, 누적질량회수곡선을 통해 양수 후 경과시간에 따른 염소이온의 질량회수율을 분석하였다. 그리고, 염소이온농도 대 누적질량회수율의 이력그래프를 작성하여 누적질량회수율에 따른 염소이온농도의 증가와 감소 변화를 분석하였다. 또한, 염소이온농도의 증가/감소 구간에 대한 선형회귀분석을 수행하여 농도 증가율과 감소율의 변화를 파악하였다. 양수정에서 관측된 경과시간별 염소이온농도 자료를 CATTI 코드의 "Converging Radial Flow With Instantaneous Injection" 해석법에 적용하여 종분산지수를 추정하였다. 양수정에서 이격거리가 2 m인 경우의 종분산지수는 0.4152 m, 이격거리가 5 m인 경우의 종분산지수는 3.2665 m이었다. 따라서 양수정에서 이격거리가 멀수록 종분산지수가 증가하는 규모종속효과를 확인하였으며, 또한 이격거리에 대한 종분산지수의 비는 각각 0.21과 0.65 정도로서 증가하였다.

• Water for future
• /
• v.29 no.4
• /
• pp.209-221
• /
• 1996

It may be difficult to make exact estimates of peak discharge or runoff depth of a flood and to establish the proper measurement for the flood protection since water stages or discharges have been rarely measured at small river basins in Korea. Three small catchments in the Su-Young river basin in Pusan were selected for the study areas. Various runoff parameters for the study areas were determined, and runoff analyses were performed using three different runoff models available in literatures; the storage function method, the discrete, linear, input-output model, and the linear reservoir model. The hydrographs calculated by three different methods showed good agreement with the observed flood hydrographs, indicating that the models selected are all capable of sucessfully modeling the flood events for small watersheds. The storage function method gave the best results in spite of its weakness that it could not be applicable to small floods, while the linear reservoir model was found to provide relatively good results with less parameters. The capabilities of simulating flood hydrographs were also evaluated based on the effective rainfall from the storage function parameters, the $\Phi$-index method, and the constant percentage method. For the On-Cheon stream watershed, the storage function parameters provided better estimates of effective rainfall for regenerating flood hydrographs than any others considered in the study. The $\Phi$-index method, however, resulted in better estimates of effective rainfall for the other two study areas.

• Journal of Korea Water Resources Association
• /
• v.42 no.8
• /
• pp.591-605
• /
• 2009

In this study the risk integrated erosion and seepage failure factor and combined risk of the levee embankment were assessed. For the research of the reliability, the risk assessment of erosion, seepage and both of them combined for the levee embankment were conducted using discharge curve and stage hydrograph generated by stochastic rainfall variation method during typhoon and monsoon season. The risk of erosion was evaluated using tractive force and the seepage analysis was performed by selecting representative cross sections for SEEP/W model analysis. And the probability of seepage failure was assessed with MFOSM analysis using critical hydraulic gradient method. Unlike deterministic analysis method, quantitative risk could be obtained and the characteristics of realistic rainfall variation patterns as well as a variety of factors contributing to levee failure could be reflected in this research. The results of this study show significantly enhanced applicability for the combined risk. As this model can be employed to determine dangerous spots for levee failure and to establish flood insurance linked with flood risk map, it will dramatically contribute to the establishment of both efficient and systematic measures for integrated flood management on a watershed.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.2
• /
• pp.4116-4120
• /
• 1976

With the use of many rivers increased nearly to the capacity, the need for information concerning daily quantities of water and the total annual or seasonal runoff has became increased. A systematic record of the flow of a river is commonly made in terms of the mean daily discharge Since. a single observation of stage is converted into discharge by means of rating curve, it is essential that the stage discharge relations shall be accurately established. All rating curves have the looping effect due chiefly to channel storage and variation in surface slope. Loop rating curves are most characteristic on streams with somewhat flatter gradients and more constricted channels. The great majority of gauge readings are taken by unskilled observers once a day without any indication of whether the stage is rising or falling. Therefore, normal rating curves shall show one discharge for one gauge height, regardless of falling or rising stage. The above reasons call for the correction of the discharge measurements taken on either side of flood waves to the theoretical steady-state condition. The correction of the discharge measurement is to consider channel storage and variation in surface slope. (1) Channel storage As the surface elevation of a river rises, water is temporarily stored in the river channel. There fore, the actual discharge at the control section can be attained by substracting the rate of change of storage from the measured discharge. (2) Variation in surface slope From the Manning equation, the steady state discharge Q in a channel of given roughness and cross-section, is given as {{{{Q PROPTO SQRT { 1} }}}} When the slope is not equal, the actual discharge will be {{{{ { Q}_{r CDOT f } PROPTO SQRT { 1 +- TRIANGLE I} CDOT TRIANGLE I }}}} may be expressed in the form of {{{{ TRIANGLE I= { dh/dt} over {c } }}}} and the celerity is approximately equal to 1.3 times the mean watrr velocity. Therefore, The steady-state discharge can be estimated from the following equation. {{{{Q= { { Q}_{r CDOT f } } over { SQRT { (1 +- { A CDOT dh/dt} over {1.3 { Q}_{r CDOT f }I } )} } }}}} If a sufficient number of observations are available, an alternative procedure can be applied. A rating curve may be drawn as a median line through the uncorrected values. The values of {{{{ { 1} over {cI } }}}} can be yielded from the measured quantities of Qr$.$f and dh/dt by use of Eq. (7) and (8). From the 1/cI v. stage relationship, new vlues of 1/cI are obtained and inserted in Eq. (7) and (8) to yield the steady-state discharge Q. The new values of Q are then plotted against stage as the corrected steadystate curve.

• Journal of Korean Society of Forest Science
• /
• v.89 no.5
• /
• pp.564-575
• /
• 2000

This study was carried out to reveal characteristics of long-term runoff by using HYCYMODEL in a small forested watershed. From May to September in 1998 and in 1999, the fitness of HYCYMODEL and runoff characteristics were estimated by HYCYMODEL using rainfall and discharge at the experimental watershed. The function of stage and discharge in the experimental watershed was determined as following equation $Q=11.148H^{2.5867}$($R^2=0.9956$). From May to September in 1998 and in 1999, the runoff rates were 57.7% in 1998 and 87.1% in 1999 at the experimental watershed. The discharge was assumed to be increased because of rainfall intensity difference and thinning. By applicability test, the HYCYMODEL showed good estimation of runoff by optimized fifteen parameters. Comparing runoff characteristics before and after thinning by calculating through HYCYMODEL, direct runoff and base runoff increased 4%, 7%, respectively as evapotranspiration decreased 11%. Parameters $D_{50}$ and $K_h$, which were related to the direct run, and a parameter $K_u$, which was related to the baseflow, were assumed to indicate that forest was changed by the effect of thinning and weathering process of bed rock.

• Journal of Korea Water Resources Association
• /
• v.51 no.9
• /
• pp.803-812
• /
• 2018

The purpose of this study is to develop Particle Swarm Optimization (PSO) automatic calibration algorithm with multi-objective functions by Python, and to evaluate the applicability by applying the algorithm to the Soil and Water Assessment Tool (SWAT) watershed modeling. The study area is the upstream watershed of Gongdo observation station of Anseongcheon watershed ($364.8km^2$) and the daily observed streamflow data from 2000 to 2015 were used. The PSO automatic algorithm calibrated SWAT streamflow by coefficient of determination ($R^2$), root mean square error (RMSE), Nash-Sutcliffe efficiency ($NSE_Q$), and especially including $NSE_{INQ}$ (Inverse Q) for lateral, base flow calibration. The results between automatic and manual calibration showed $R^2$ of 0.64 and 0.55, RMSE of 0.59 and 0.58, $NSE_Q$ of 0.78 and 0.75, and $NSE_{INQ}$ of 0.45 and 0.09, respectively. The PSO automatic calibration algorithm showed an improvement especially the streamflow recession phase and remedied the limitation of manual calibration by including new parameter (RCHRG_DP) and considering parameters range.

• Journal of Korean Society of Forest Science
• /
• v.109 no.4
• /
• pp.429-437
• /
• 2020

In this study we quantified the long-term change in discharge against precipitation in a forested watershed and investigated how the growth of forest trees influences these changes. We found a proportional relationship between precipitation and discharge for each year, and discharge decreased gradually with time. Precipitation and discharge were highest in July and August, and the changes in precipitation, discharge, and runoff rate did not always coincide, given that high runoff rate was shown in August and September. The monthly coefficient of variation (CV) for discharge was larger than that for precipitation, and the deviation between precipitation and discharge increased gradually. From 2011 to 2017, the gradient of the trend line for the change of total discharge and direct runoff against precipitation decreased, whereas the gradient of the base flow increased in this same time period. A possible explanation is that the water holding capacity of soil deposits increased as the forest soil of the Palgong Mountain watershed developed and the increase of base flow rose with groundwater level together with that of outflow quantity. The coefficient of flood recession was lower in the period 2011 to 2017 than in 2003 to 2010; thus, the reduction of discharge was mitigated and remained steady as time progressed. We conclude from these results that the discharge of surface runoff decreased as tree growth and base flow increased; however, the water yield function of the forest increased gradually.

• Journal of Korea Water Resources Association
• /
• v.41 no.12
• /
• pp.1219-1230
• /
• 2008

Stream inflows induced by flood runoffs have a higher density than the ambient reservoir water because of a lower water temperature and elevated suspended sediment(SS) concentration. As the propagation of density currents that formed by density difference between inflow and ambient water affects reservoir water quality and ecosystem, an understanding of reservoir density current is essential for an optimization of filed monitoring, analysis and forecast of SS and nutrient transport, and their proper management and control. This study was aimed to quantify the characteristics of inflow density current including plunge depth($d_p$) and distance($X_p$), separation depth($d_s$), interflow thickness($h_i$), arrival time to dam($t_a$), reduction ratio(${\beta}$) of SS contained stream inflow for different flood magnitude in Daecheong Reservoir with a validated two-dimensional(2D) numerical model. 10 different flood scenarios corresponding to inflow densimetric Froude number($Fr_i$) range from 0.920 to 9.205 were set up based on the hydrograph obtained from June 13 to July 3, 2004. A fully developed stratification condition was assumed as an initial water temperature profile. Higher $Fr_i$(inertia-to-buoyancy ratio) resulted in a greater $d_p,\;X_p,\;d_s,\;h_i$, and faster propagation of interflow, while the effect of reservoir geometry on these characteristics was significant. The Hebbert equation that estimates $d_p$ assuming steady-state flow condition with triangular cross section substantially over-estimated the $d_p$ because it does not consider the spatial variation of reservoir geometry and water surface changes during flood events. The ${\beta}$ values between inflow and dam sites were decreased as $Fr_i$ increased, but reversed after $Fr_i$>9.0 because of turbulent mixing effect. The results provides a practical and effective prediction measures for reservoir operators to first capture the behavior of turbidity inflow.