• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.613-623
• /
• 2000

Digital TV tuner for 8-VSB modulation was developed with satisfying the requirements of ATSC. The double frequency conversion and the active tracking filter in the front-end were used to reduce interference of the adjacent channels and multi-channels, which suppress If beat and image band. However, it was impossible to get frequency mapping between tracking filter and first VCO(Voltage Controlled Oscillator) in the double conversion digital TV tuner differing from conventional NTSC tuner. This paper, therefore, suggests the available structure and a new method for automatic frequency selection by obtaining the mapping of frequency characteristic over tracking voltage and the combined hardware which compose of Micro-controller, EEPROM, D/A(Digital-to-Analog Converter), OP amp and switch driver to solve above problems.

• Journal of Advanced Navigation Technology
• /
• v.14 no.3
• /
• pp.358-366
• /
• 2010

In the wireless network the congestion and delay occurs mainly when there are too many packets for the network to process or the sender transmits more packets than the receiver can accept. The congestion and delay is the reason of packet loss which degrades the performance of multimedia streaming. This paper proposes a novel transmission rate monitoring-based optimization mechanism to optimize packet loss and to improve QoS. The proposed scheme is based on the trade-off relationship between transmission rate monitoring and overhead monitoring. For this purpose this paper processes a source rate control-based optimization which optimizes congestion and delay. Performance evaluated RED, TFRC, and the proposed mechanism. The simulation results show that the proposed mechanism is more efficient than REC(Random Early Detection) mechanism and TFRC(TCP-friendly Rate Control) mechanism in packet loss rate, throughput rate, and average response rate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.6
• /
• pp.27-33
• /
• 1984

This paper is an experimental gaudy on the digital hardware implementation of the R2-MF Receiver for 32 channel configurations used in signalling systems between ESS. There are many methods to detect MF signal by DSP techniques, but the requirement for MF detection needs not sharp frequency response, needs only decision about some specific frequencies exist or not at discrete frequency sampling points. The hardware used to implement this algorithm is Am 2900 series "bit-slice microprocessor" chips based on the microprogramming techniques for real time signal processing. And we used the additional Z-80A processor chips for the system control and the decision about which is the right MF signal from the detected MF spectrums. Hence we could enhance the flexibilities of the hardware and the software, this leads that this system is well suits for signalling systems used in TDM ESS.n TDM ESS.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.12
• /
• pp.43-52
• /
• 1999

We propose a new method for tuning of center wavelength in photorefractive filter using $LiNbO_3$ crystal doped with 0.015Wt.% Fe. through the filter bandwidth property analysis using the geometrical method, a new wavelength selectivity theory was presented. In this scheme, the tuning of the center wavelength can be achieved by the real time incident angle control of the received heam, which was gotten by the spatial light modulator. So, tuning time depend on the response time of the SLM and results in the high speed turing. Because the use of thermally fixed grating in our filter, it has uniform diffraction property to the all filtering wavelength. Designed tunable filter has 4nm bandwidth and composed of the three channel with 10nm space. From the optical experiment, we get the 4.5nm, 4.25nm, 4nm bandwidth and 1530.5nm, 1540.5nm, 1549.5nm center wavelength respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.185-191
• /
• 2015

This paper suggest the safety class communication board in order to design the safety network of the nuclear safety class controller. The reactor protection system use the digitized networks because from analog system to digital system. The communication board shall be provided to pass the required performance and test of the safety class in the digital network used in the nuclear safety class. Communication protocol is composed of physical layer(PHY), data link layer(MAC: Medium Access Control), the application layer in the OSI 7 layer only. The data link layer data package for the cyber security has changed. CRC32 were used for data quality and the using one way communication, not requests and not responses for receiving data, does not affect the nuclear safety system. It has been designed in accordance with requirements, design, verification and procedure for the approving the nuclear safety class. For hardware verification such as electromagnetic test, aging test, inspection, burn-in test, seismic test and environmental test in was performed. FPGA firmware to verify compliance with the life-cycle of IEEE 1074 was performed by the component testing and integration testing.

• Journal of IKEEE
• /
• v.19 no.3
• /
• pp.311-318
• /
• 2015

This dissertation proposes method for development technology of voice and SMS(Short Message Service) alarming system based on modbus protocol. The proposed technology is composed of the following 3 stages; hardware development based on microprocessor, development of input and output driver for modem, mp3 decoder, making modbus protocol stack. In the stage of hardware development based on microprocessor, we develop hardware which receives alarm from modbus master and transmit sms message, play mp3. In the stage of development of input / ouput device driver such as modem, mp3 decoder, we develop program which control each devices. In the stage of making modbus protocol stack, voice and sms alarm system is made for receiving alarm via modbus protocol. To evaluate performance of proposed technology, we issued alarm to voice and sms alarming system on purpose. As a result, response speed of detecting alarm was 10.7ms, communication distance was 1.2Km, operating temperature was from $-25^{\circ}C$ to $70^{\circ}C$, we confirmed supporting modbus protocol. And we verified that proposed voice and sms alarming system in the thesis has a performance to be used as an industrial building alarming system.

• Journal of IKEEE
• /
• v.25 no.1
• /
• pp.156-167
• /
• 2021

In this paper, we propose a digital transceiver unit design for in-building of 5G optical repeaters that extends the coverage of 5G mobile communication network services and connects to a stable wireless network in a building. The digital transceiver unit for driving the proposed 5G optical repeater is composed of 4 blocks: a signal processing unit, an RF transceiver unit, an optical input/output unit, and a clock generation unit. The signal processing unit plays an important role, such as a combination of a basic operation of the CPRI interface, a 4-channel antenna signal, and response to external control commands. It also transmits and receives high-quality IQ data through the JESD204B interface. CFR and DPD blocks operate to protect the power amplifier. The RF transmitter/receiver converts the RF signal received from the antenna to AD, is transmitted to the signal processing unit through the JESD204B interface, and DA converts the digital signal transmitted from the signal processing unit to the JESD204B interface and transmits the RF signal to the antenna. The optical input/output unit converts an electric signal into an optical signal and transmits it, and converts the optical signal into an electric signal and receives it. The clock generator suppresses jitter of the synchronous clock supplied from the CPRI interface of the optical input/output unit, and supplies a stable synchronous clock to the signal processing unit and the RF transceiver. Before CPRI connection, a local clock is supplied to operate in a CPRI connection ready state. XCZU9CG-2FFVC900I of Xilinx's MPSoC series was used to evaluate the accuracy of the digital transceiver unit for driving the 5G optical repeater proposed in this paper, and Vivado 2018.3 was used as the design tool. The 5G optical repeater digital transceiver unit proposed in this paper converts the 5G RF signal input to the ADC into digital and transmits it to the JIG through CPRI and outputs the downlink data signal received from the JIG through the CPRI to the DAC. And evaluated the performance. The experimental results showed that flatness, Return Loss, Channel Power, ACLR, EVM, Frequency Error, etc. exceeded the target set value.