• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.119.1-119.1
• /
• 2016

크라이오 워터펌프(CWP)는 크라이오 펌프(CP)와 달리 10 K 활성탄 어레이는 장착하지 않고 100 K 정도로 냉각시킨 배플만을 사용하여 물의 배기속도를 최적화 하는 데 초점을 맞춘 진공펌프다. 용기 압력이 10-9 mbar 대가 될 때까지는 잔류기체의 90% 이상이 수분이므로 다른 기체들의 배기 보다는 물을 잘 배기하는 것이 배기시간을 단축하고 도달 진공도를 낮추는 첩경이라는 아이디어에 근거를 두고 있다. CWP는 물 흡착확률을 거의 1에 가깝게 만들어서 오리피스 컨덕턴스에 육박하는 이상적인 펌프를 제작할 수 있지만 용도상 직부형(close type), 통과형(in-line type) 및 내장형(in-vessel type) 등 세 가지 다른 형태에 따라 성능도 약간씩 다르다. CWP는 모든 기체에 반응하는 정통적인 CP에 비해 훨씬 간단하고 저렴하게 만들 수 있으면서도 진공 시스템에 큰 영향을 미칠 수 있지만 물 이외의 기체들을 배기할 펌프가 필요하다는 측면에서 활용에 제약이 있다. 만일 TMP를 이미 사용하고 있거나 작은 TMP를 추가로 달아서 충분히 작동이 가능한 시스템이면서 수분 발생이 많은 곳이나, 또 활성탄의 오염이나 산소 분위기 등 CP 투입이 꺼려지는 환경이라면 CWP 사용이 좋은 선택이 될 수 있다. CWP의 물 배기용량은 CP의 알곤이나 질소 배기용량에 준하는 크기로 0.5g/cm2 이상임이 실험적으로 입증되었다. 따라서 일반적인 상황에서 정상 작동시 대부분의 기체는 TMP로 배출하고 잔류 수분만 포집하므로 CP처럼 주기적인 재생이 필요 없다. 필요하다면 CWP는 금속 표면에 응축된 물을 드라이펌프 작동만으로 쉽게 제거할 수 있고 혹시 오염 물질이 붙어도 세척이 용이하다. 이런 사용상 융통성과 여러 가지 장점에도 불구하고 그동안 물배기에 대한 인식이 미흡하고, 또 부수적이고 추가적인 비용이 드는 것으로 생각되어 주목을 받지 못했지만 디스플레이와 반도체 산업을 필두로 물 분압을 낮추고 생산수율을 높이는 것에 점점 더 관심이 높아지면서 CWP에 대한 수요도 높아지고 있다. 본 보고에서는 20인치 통과형 CWP를 만들고 14인치 TMP에 얹어 복합 진공배기시스템을 구성한 후 물 배기속도와 알곤, 질소 및 수소 배기속도를 측정하고 예측치와 비교했다. 아울러 물 배기용량 측정 및 CWP의 온도제어와 펌프재생 특성 평가 결과도 정리했다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.96-96
• /
• 2012

복합분자펌프는 기존의 터보분자펌프 turbine blade에 spiral grooved를 추가하여 초고진공(10-8Pa)에서 저진공(330Pa)까지 넓은 압력범위에서 사용할 수 있고 이 펌프를 사용함으로서 완전 oil free한 진공시스템을 만들 수 있는 특징을 가지고 있다. 특히, 회전체를 비접촉으로 지지하는 자기베어링 방식을 적용함으로써, 진동은 극히 작고 베어링수명은 길면서 중저진공에 대한 배기속도가 크고 임의의 방향으로 접속이 가능하여 반도체 및 디스플레이 제조 공정과 같은 첨단산업의 다양한 분야에 쉽게 적용되고 있으며, 그 적용 분야와 시장은 계속 성장하고 있다. 고 진공과 배기 속도의 달성을 위해서, 고속으로 이동하는 격면과 기체분자를 충돌시켜, 기체 분자를 원하는 방향으로 유도하는 작동원리를 가지고 있다. 특히 공기분자의 밀도가 매우 낮은 희박가스 상태에서 고속 회전하는 blade로 공기분자를 쳐내면서 작동됨으로써 날개의 상하 압력차에 의한 공기력보다도 날개의 고속회전이 매우 중요시되고 압력으로는 10-1 Pa 이하의 분자영역에서 그 성능을 최고로 발휘할 수 있다. 이러한 복합 펌프의 주요 장점은 다음과 같다. 1. 10-8 Pa (10-10 torr) ~ 10 Pa (1 torr) 까지 넓은 영역에서 배기가 가능하다. 2. 탄화수계의 대하여 높은 압축특성을 가지고 있고, 윤활유를 사용하지 않으므로 얻을 수 있는 진공상태가 고청정하다(oil free). 3. 정밀 5축제어 자기베어링으로 완전히 부상하여 회전함으로서 마모가 없고 진동이 최소화하였을 뿐 만 아니라, 또한 운전음도 거의 없다. 4. 설치조건에 제한이 없고 고장이 거의 없다. 특히 복합분자펌프는 탄화수소화합물이 없는 진공을 생성시키면서 구성요소가 간단한 반면 폭넓은 진공대역을 충족하기 때문에 산업계와 연구계의 주요 첨단 분야에서 광범위하게 사용되고 있으며, 최근 반도체 및 디스플레이, 바이오엔지니어링 등의 발전으로 적용분야가 넓어지고 있다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.6
• /
• pp.652-658
• /
• 2015

The purpose of this study is to investigate the effects of changing dimension of a soft tube in a peristaltic pump on deformation, stress and fluid flow rate of the peristaltic pump. Geometries of the peristaltic pump is created in a Catia drawing software based on specifications of a real peristaltic pump. Afterwards, the geometries of this pump is imported into a commercial Ansys software to calculate deformation, stress, and fluid flow rate of this pump. The simulation results showed that the deformation and stress of the soft tube is increased by increasing soft tube diameter from 2 mm to 4 mm. When the tube diameter is increased to 5 mm and tube thickness is reduced to 0.5 mm, the soft tube is damaged. The highest fluid flow rate could be found at the tube thickness and diameter of 1 mm and 4 mm, respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.3
• /
• pp.297-304
• /
• 2014

The purpose of this study is to evaluate the experimental performance characteristics of a water-to-water geothermal heat pump featuring a vapor refrigerant injection for the production of hot water. The performance of geothermal heat pump with a vapor injection was evaluated by comparing with that of a conventional geothermal heat pump without a vapor injection. For heating operation, the geothermal heat pump with a vapor injection is superior in COP and heating capacity. The vapor injection was more effective for supplying hot water while overloading. The vapor injection was effective for the improvement of the cooling capacity. However, the vapor injection was not effective for the increasing of COP according to the increased input of a compressor. The advantage of vapor injection in water-to-water geothermal heat pump become disappeared while cooling operation with lower part loading.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.3
• /
• pp.308-314
• /
• 2017

Jet pump in automotive fuel tank module is used to deliver fuel to fuel pump so that the pump is operated without aeration in suction side. In this study, three dimensional simulation model of jet pump is developed to understand performance variation over design parameters. Performance of jet pump is also investigated experimentally in terms of operating pressures. The experimental data is used to verify the three dimensional simulation model of jet pump. Verification results show that the three dimensional simulation model of jet pump is about 1% error with experiment. The simulations are conducted in terms of throat ratio and primary flow induction angle. As the throat ratio is increased, the flux ratio is trade-off at 3 times of throat diameter. On the other hand, as primary flow induction angle is increased, vapor pressure inside the nozzle is decreased. In summary, the results show that liquid jet pump has to be optimized over design parameters. Additionally, high velocity of induced flow is able to evolve cavitation phenomena inside the jet pump.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.1
• /
• pp.121-126
• /
• 2016

Hydraulic performance of a micro-bubble pump has been analyzed by numerical simulation and experimental measurements. Flow recirculation apparatus between the pump inlet and outlet reserviors has been adopted to measure pump performance according to flow conditions sequentially. To analyze three-dimensional flow field in the micro-bubble pump, general analysis code, CFX, is employed. SST turbulence model is employed to estimate the eddy viscosity and compared the pump performance to k-${\varepsilon}$ model. Unstructured grids are used to represent a composite grid system including blade, casing and inlet casing. It is found that the numerical model used in the present study is effective to evaluate the pump performance. From the numerical simulation, low velocity region due to pressure loss is decreased where pump efficiency has maximum value. Detailed flow field inside the micro-bubble pump is also analyzed and compared.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.5
• /
• pp.324-330
• /
• 2021

In recent years, polymer electrolyte membrane fuel cell (PEMFC) based cogeneration system has received more and more attention from energy researchers because beside electricity, the system also meets the residential thermal demand. However, the low-quality heat exited from PEMFC should be increased temperature before direct use or storage. This study proposes a method to utilize the heat exhausted from a 10 kW PEMFC by coupling a heat pump. Two different configuration using heat pump and a reference layout with heater are analyzed in term of thermal and total efficiency. The system coefficient of performance (COP) increases from 0.87 in layout with heaters to 1.26 and 1.29 in configuration with heat pump and cascade heat pump, respectively. Lastly, based on system performance result, another study in economics point of view is proposed.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.4
• /
• pp.369-375
• /
• 2019

Air conditioners adopting high energy efficiency and low global warming potential (GWP) refrigerant are being developed globally. In case of commercial air conditioner, R32 with lower GWP than R410A is attracting industrial attentions. In this study, the performance of water-to-water geothermal heat pump adopting R32 is compared with that of the heat pump using R410A. By using R32 instead of R410A, heating capacity and COP in heating standard condition can be increased by 8.8% and 6.3% respectively. Also, cooling capacity and COP in cooling standard condition can be increased by 5.3% and 3.1% respectively by using R32. But in case of using R32, systemic improvements are required to decrease discharge temperature of compressor since discharge temperature rises abnormally in heating operations.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.04a
• /
• pp.87-90
• /
• 2007

Fuel cell power system was developed for high-endurance unmanned aerial vehicle (UAV). Liquid chemical hydride was selected as a fuel due to its high energy density. Liquid storage of the fuel is an ideal alternative solution of the existing compressed hydrogen storage. The fueling system that extracts hydrogen from chemical hydride consists of catalytic reactor, micro-pump, fuel cartridge, separator, and controller. The fuel cell power system including the fueling system and the fuel cell that generates electricity was integrated into a proposed UAV. The performance verification of the fuel cell power system was performed to use as a power plant of the UAV.

• Transactions of the Korean hydrogen and new energy society
• /
• v.4 no.1
• /
• pp.21-30
• /
• 1993

The operational characteristics of a metal hydride heat pump system are strongly dependent on the amound of hydrogen gas transferred by hydriding and dehydriding reactions between the reactors under dynamic conditions. A new metal hydride heat pump combined with hydrogen compressor was constructed and the dependency of its operating conditions on such as cycle time, amount of hydrogen to be transferred between two reacting metal hydride reactors, operating temperature, and heat transmission characteristics of the reactors was investigated to find the optimum operating efficiency. These conditions were also evaluated in connection with the cooling output and hydrogen compressor connected to the system in order to enhance the total efficiency.