• Membrane Journal
• /
• v.27 no.6
• /
• pp.477-486
• /
• 2017

Hydrogen is one of energy storage systems, which could be transfer from electric energy to chemical energy or from chemical energy to electric energy, and is as an energy carrier. Water electrolysis is being investigating as one of the hydrogen production methods. Recently, water electrolysis receive attention for the element technology in PTG (power to gas) and PTL (power to liquid) system. In this paper, it was explained the principle and type for the water electrolysis, and recent research review for the alkaline water electrolysis.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.4
• /
• pp.266-275
• /
• 2008

The performance improvement of each part for durability, safety and cost of high pressure storage system for fuel cell vehicle has been focused so far. However, for the mass production of fuel cell vehicle, it is necessary to evaluate durability and safety in system module and vehicle level. The test procedure to evaluate vibration and collision safety of high pressure hydrogen storage system for the fuel cell vehicle is established and its reliability is verified.

• Transactions of the Korean hydrogen and new energy society
• /
• v.11 no.1
• /
• pp.43-49
• /
• 2000

The heat transportation from a complex of industry to a rural area needs more efficient method because the distance between them is usually more than 10km. Conventional heat transportation using steam or hot water via pipe line has limits in transportation distance (about 3~5 km) because of the heat loss and frictional loss in the pipe line. Metal hydride can absorb or discharge hydrogen through exothermic or endothermic reaction. After releasing hydrogen from metal hydride by means of the waste heat from industry, we can transport this hydrogen to urban area via pipe line. In urban areas, other metal alloy reacts with this hydrogen to form metal hydride and produces heat for heating. Cool heat is also obtained if it is possible to use metal hydride with low reaction temperature. Therefore, metal hydride can be used as a media for transportation and storage of heat. $MmNi_{4.5}Al_{0.5}Zr_{0.003}$, $LaNi_5$, $Zr_{0.9}Ti_{0.1}Cr_{0.6}Fe_{1.4}$, $MmNi_{4.7}Al_{0.1}Fe_{0.1}V_{0.1}$ alloys were selected for this purpose and the properties of those metal hydrides were discussed. The design and control techniques were proposed and discussed for this heat transportation system using metal hydride.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.37-40
• /
• 2008

We have concentrated on the performance improvement of each part for durability, safety and cost of high pressure storage system for fuel cell vehicle so far. But for the mass production of fuel cell vehicle, it is necessary to evaluate durability and safety in system module. We built the standard to evaluate and collision safety of high pressure storage system for fuel cell vehicle, and could verify reliability of high pressure storage system.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.5
• /
• pp.469-476
• /
• 2015

The purpose of this work is to investigate main factors to design a solid-state hydrogen stroage system with magnesium hydride with 10 wt% graphite using numerical simulation tools. The heat transfer characteristic of this material was measured in order to perform the highly reliable simulation for this system. Based on the measured effective thermal conductivity, a transient heat and mass transfer simulation revealed that the total performance of hydrogen storage system is prone to depend on heat and mass transfer behaviors of hydrogen storage medium instead of its inherent kinetic rate for hydrogen adsorption. Furthermore, we demonstrate that the thermodynamic aspect between equlibrium presssure and temperature is one of key factor to design the hydrogen storage system with high performance using magnesium hydride.

• Transactions of the Korean hydrogen and new energy society
• /
• v.31 no.6
• /
• pp.558-563
• /
• 2020

Hydrogen is attracting attention as an alternative energy source as an eco-friendly fuel without emitting environmental pollutants. In order to use hydrogen as an energy source, technologies such as hydrogen production and storage must be used, and new storage methods are being studied. In this study, the behavior of hydrogen in the storage tank were numerically studied under high-pressure hydrogen discharge conditions in a Type III hydrogen tank. Numerical results were compared with the experimental value and the results were quantitatively analyzed to verify the numerical implementation. With the results of pressure and temperature values under a given discharge condition, the Redich-Kwong gas model showed the adequate models with the smallest error between numerical and experimental results.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.558-559
• /
• 2008

본 논문은 미 일리노이 주립대 어바나-샴페인 캠퍼스에서 주로 군사용 응용 관련하여 개발 중인 마이크로 PEM 연료전지 시스템 개발에 대한 논문이다. 본 연구는 수소 저장 장치까지 포함하여 1 $mm^3$의 초소형 연료전지 시스템을 목표로 진행 중이며 본 논문은 이러한 진행 과정 중 화학적 하이드라이드 기반의 수소 발생기와 10 $mm^3$의 시스템 개발 과정에 대해 보고한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.98.1-98.1
• /
• 2011

전 세계적으로 대표적인 대중교통으로 천연가스버스가 운행 중에 있으며, 천연가스의 저장을 위하여 대부분의 차량이 복합용기를 사용하고 있다. 또한 친환경자동차로 개발되고 있는 수소연료전지자동차도 수소 저장용으로 복합용기를 적용하여 상용화를 추진 중에 있다. 복합용기의 상용화가 증가하면서 복합용기의 안전성 확보가 가장 중요한 이슈가 되고 있다. 기체상태의 고압가스를 교통수단에 적용하기 위하여, 저장매체인 고압복합용기의 안전성 및 기술 확보를 위한 기술개발과 안전기준의 확립을 위한 기준개발이 미국, 유럽, 일본 등 다수의 국가에서 진행되고 있다. 현재 복합용기의 안전성을 확인하는 기준은 각 나라의 기준에 따라 진행되고 있으며 천연가스자동차용 저장용기 국제표준으로는 ISO 11439가 적용되고 있다. 수소연료전지자동차용 수소용기의 안전기준은 아직 확립되지 않은 상태이며, 개발된 초안으로는 국제규정으로 UN ECE R No.79 및 국제기술표준으로 ISO/TS 15869가 있다. 개발 중인 국제기준 및 국내기준에서 가장 취약한 부분이 화염시험이다. 화염시험은 자동차에 화재가 발생했을 경우 용기의 폭발을 막기 위하여 안전밸브가 정상적으로 작동하는 지를 확인하는 시험이다. 하지만 현재의 시험방법으로는 자동차에서 발생하는 국부적인 화염에 대한 안전성을 확인하기가 어려운 실정이다. 본 연구에서는 국내의 화염시험기준을 개발하기 위해 수행된 화염시험에 대한 결과와 화염시험장치를 제안하고자 한다.

• Transactions of the Korean hydrogen and new energy society
• /
• v.26 no.4
• /
• pp.331-338
• /
• 2015

Solar air heaters (SAHs) are simple in design and widely used for solar energy collection devices, and a packed bed is one of typical solar energy storage systems of thermal energy captured by SAHs. This paper presents mathematical modeling and simulation on the thermal performance of various packed bed energy storage systems. A MATLAB program is used to estimate the thermal efficiency of packed bed SAH. Among the various packed bed energy storage systems considered, the wire mesh screen packed bed SAH shows the best thermal efficiency over the entire range of design conditions. The maximum of thermal efficiency of packed bed SAH with wire mesh screen matrices has been found to be 0.794 for Re=2000 - 20000 and ${\Delta}T/I=0.002-0.02$.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.34-50
• /
• 2022

Since the Paris climate agreement, reducing greenhouse gases has been the most important global issue. In particular, it is necessary to reduce fossil fuels in the mobility sector, which accounts for a significant portion of total greenhouse gas emissions. In this paper, we investigated the economic feasibility of green mobility energy supply chains, which supply hydrogen as fuel to hydrogen vehicles based on electricity from renewable energy sources. The design and operation costs were analyzed by evaluating nine scenarios representing various combinatorial possibilities such as renewable energy generation, hydrogen production through water electrolytes, hydrogen storage and hydrogen refueling stations. Simulation calculations were made using Homer Pro, widely used commercial software in the field. The experience gained in this study could be further utilized to construct actual hydrogen energy systems.