• Journal of Environmental Health Sciences
• /
• v.24 no.1
• /
• pp.132-140
• /
• 1998

Laboratory-scale experiments were conducted using a three-stage rotating biological contactor unit followed by lime precipitation and sedimentation with effluent recycle to the first stage. The purpose of this study was to evaluate the effects of hydraulic loadings of 0.031-0.076 $m^3/m^2/d and recycle ratio of 1 to 3 on the simultaneous removal of organics and nutrients from domestic wastewater. Lime was added to maintain pH of 10.4-11.0 in the coagulation-flocculation reactor. Results showed that the highest nitrogen removal rate of 70.5% occurred at the lower hydraulic loading of 0.031 $m^3/m^2/d at a recirculation rate of 300%, and similarly, highest nitrification occurred at the same hydraulic loading and recycle ratio. Concentration of ammonia nitrogen in the effluent was less than 1 mg/l at the same operating conditions for higher nitrogen removal. Whereas, high BOD and COD removal was observed at hydraulic loading rate of 0.054 $m^3/m^2/d, and high removal of organic matter was evident from the consistent low COD and BOD value. Results obtained from the operating condition of higher loading rate, 300% of recycle rate showed the highest removals. Increasing in recycle rate and hydraulic loading rate increased the volatile solids fraction of the sludges generated to the extent of 47% at 0.076 $m^3/m^2/d hydraulic loading and 300% recirculation rate. Since pH in the flocculator was maintained at the pH of 10.4-11.0, above 90% removal of phosphorus was obtained. Average concentration of suspended solids was always maintained over 40 mg/l in the effluent. Therefore an RBC unit operating at a hydraulic loading near 0.031 $m^3/m^2/d with a recycle rate of 300% is a viable and feasible alternate conditions to produce an effluent with relative low organic matter and phosphorus, provided that there is a neutralization unit to control the pH and SS of the effluent.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2008.05a
• /
• pp.2019-2022
• /
• 2008

본 연구에서는 유역과 점오염원, 비점오염원을 종합하고, 방대한 자료를 쉽게 적용할 수 있으며 유역의 지형적인 특성과 수리 수문학적인 특성 및 오염원의 공간적인 분포 특성을 반영하여 유달부하량의 모의가 가능한 SWAT 모형을 이용하여 낙동강 유역의 주요 지류에 대한 유달율산정에 관하여 검토하고자 한다. 본 연구의 대상지역은 낙동강 유역 중 본류가 시작되는 곳으로부터 금호강지류와 합류하는 지점까지로 선정하였으며 SWAT 모형에 적용되는 자료는 2005년 1월${\sim}$12월의 실측 자료를 이용하였다. 유달율 산정 항목으로는 BOD, T-N, T-P를 선정하였다. 분석 결과 전반적으로 강수의 영향을 많이 받는 계절에 유달율이 높게 산정되었으며 또한 유역면적 보다 유량과의 상관성이 유달율에 많은 영향을 미치는 것으로 검토되었다. 이러한 연구결과를 토대로 정확한 배출부햐량의 산정을 위하여 강우의 영향과 발생부하 원단위에 대한 지속적인 연구가 필요하다고 사료된다.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.11
• /
• pp.3356-3371
• /
• 2000

본 논문에서는 분산시스템 환경에서 n개의 노드가 결함일 경우, 결함을 허용해 주고, 시스템의 안정성을 유지하면서, 결함 노드의 부하를 정상 노드로 조절하기 위하여 부하 조절 알고리즘 전송정책, 위치 정책, 선정 정책을 제안하였다. 이러한 메카니즘은 부하 상태의 정보를 효과적으로 획득하고, 응답 시간을 줄이기 위하여 자기 학습 경험을 기반으로 하는 최적의 알고리즘을 선정할 수 있었다. 결과적으로 이를 기반으로 유사한 상황에서도 최적의 알고리즘을 선정할 수 있음을 알 수 있었다. 각 기법들의 효율성에 영향을 미칠 수 있는 매개변수를 적용하여 성능평가를 하였다. 성능평가 결과 작업 도착 율, 서비스 율, 노드 결합 율은 서로간에 영향을 주지 못하고, 다만 결함 수리 율과 특히 부하의 이주에 대한 통신 지연 시간의 크기에 민감한 영향을 주었다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.565-565
• /
• 2016

농림부는 농업지역에서 발생하는 비점오염원을 관리하기 위해 다양한 최적관리기법(BMP)에 대해 연구를 수행하여 효과를 검증하였으나 이를 광역 단위로 보급하여 실제 영농지역에서 BMP의 효과를 측정한 연구는 부족한 실정이다. 따라서 본 연구에서는 논 지역을 대상으로 물관리기술(물꼬)과 시비관리기술(완효성 비료) BMP를 보급하고 광역 단위로 BMP의 효과를 측정하고자 하였다. 연구대상지구는 새만금 지역에 위치한 전라북도 부안군 용계리 일대에 위치하고 있으며, 벼농사가 활발하게 이루어지고 있는 지역을 선정하였다. 논에 보급된 BMP의 효과를 측정하기 위해 BMP 참여 농가를 선정하여 물꼬와 완효성 비료를 보급하였으며, 용수로와 배출구 3지점을 선정하여 관개량을 측정하고 유출량을 측정하였다. 또한 관개수와 대조구, 처리구별(대조구, 물꼬, 완효성, 물꼬+완효성) 수질을 분석하여 배출구 별로 단위면적당 오염부하량을 산정하고 이를 통해 대조구 대비 처리구의 저감율을 분석하였다. 분석 결과, 대조구 대비 처리구의 단위면적당 오염부하량의 저감율은 SS 63.6%, BOD 45.5%, $COD_{Mn}$ 26.5%, $COD_{Cr}$ 40.1%, T-N 16.0%, T-P 12.9%, TOC 11.4%로 나타났다. 또한 연구대상지구를 SO#1(완효성 비료 95%, 비참여 농가 5%), SO#2(완효성 비료 2%, 물꼬 8%, 완효성 비료+물꼬 40%, 비참여 농가 40%), SO#M(완효성 비료 96%, 비참여 농가 4%) 3개의 배출구로 구분하여 BMP 보급 효과를 측정한 결과, 대조구 대비 SO#1에서는 수질항목별로 10.6 ~ 85.5%, SO#2는 8.1 ~ 45.9%, SO#M은 10.7 ~ 86.2%의 범위로 저감된 것으로 분석되었으며, 특히 SS의 단위면적당 오염부하 저감율이 가장 큰 것으로 나타났다. 하지만 본 연구는 7월부터 10월까지 측정된 데이터를 활용하여 산정하였기 때문에 써레질, 이앙기간에 발생한 단위면적당 오염부하량은 포함되지 않은 결과이며, 각 배수구역별 유입량의 경우 정확한 측정에 어려움이 있어 전체 관개량 대비 관개 면적을 이용하여 단위면적당 유입량을 산정하였기 때문에 추가적인 연구를 통해 효과를 검증할 필요가 있을 것으로 판단된다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.3
• /
• pp.176-180
• /
• 1992

Nitrification Is an important facet of water recycling fish culture system, because the toxic cation ammonia is converted to the innocuous anion nitrate. This study was attempted to find the optimal design factor of submerged filter for ammonia removal in water recycling fish culture system. The experimental system was designed submerged filter with corrugated skylight plate, and operated in the fish farm, National Fisheries University of Pusan. When the influent ammonia concentration was about 10mg/l (9.43-13.66mg/l) nitrification rates were tested for the removal of ammonia over a four stage of the hydraulic loadings. The submerged filter removed 76.24, 62.88, 39.09 and $9.20\%$ of the ammonia to hydraulic load of 0.028, 0.037, 0.056 and $0.111m^3/m^2$. day, respectively. We can apply the above data to the material balance on the ammonia concentration in a fish reservoir, and conclude that the maximum allowable ammonia production was 1.52mg/min, and the optimal hydraulic loading was $0.047m^3/m^2$\;\cdot day$, in order to maintain the ammonia concentration below 10mg/l in the fish reservoir.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.3
• /
• pp.77-86
• /
• 2002

위성은 일단 한 번 발사하고 나면 운용궤도상에서 수리 및 회수가 거의 불가능하기 때문에 위성에 들어가는 모든 개발 부품들은 완벽한 설계, 충분한 해석, 고 작업도의 제작, 그리고 다양한 시험이 반드시 수반되어야 한다. 위성시스템에서 전자 소자의 신뢰성에 영향을 주는 인자는 다양하다. 과도한 열은 전자소자의 실패를 유발해서 결과적으로는 전체 위성의 실패를 유도할 수 있다. 이 논문에서는 다목적 실용위성 2호의 고전력 소산 전장품의 열부하 완화를 위한 방안을 경우별로 연구 비교하였다. 고전력 소산 전장품의 열부하를 완화하기 위해서는 하우징 두께의 증가가 필요하며, 전력조절기의 다이오드나 트랜지스터처럼 전력소산이 큰 소자에 대해서는 장착위치를 변경하거나 장착 부분의 열전도율을 증가시키는 방법이 필요하다. 또한 전력조절기처럼 장착면이 좁은 경우에는 복사의 영향이 크며, 이러한 전장품의 열부하를 완화하기 위해서는 주위 벽면의 온도를 낮추거나 하우징 표면 방사율을 증가시키는 방법이 효과적임이 알 수 있다.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.39 no.5
• /
• pp.97-108
• /
• 1997

Natural wastewater treatment systems using the constructed wetland system were evaluated for the wastewater from the industrial complex in rural areas. For the treatment of wastewater from the industrial complex in rural area, a pilot plant of the constructed wetland system was installed at Baeksuk agri-industrial complex in ChunahnCity, Chunchungnam-Do. The experiment with this pilot plants was performed for 1996 and 1997. Results of the study were summarized as follows. For the BOD and COD, when the pollutant loading of them was about 1 3.8g/$m^2$. day (the concentration was l24.0mg/${\ell}$) arid 24.4g/$m^2$.day(the concentration was 220.Omg/${\ell}$), the removal rate of them was high, 90.2% and 93.4%, respectively. For the SS, the effluent concentration was consistently lower than the water quality standard even though the influent concentration varied significantly, which showed that SS was removed by the system effectively which consist of soil and plants. For the T-N and T-P, when the influent pollutant loading of them were moderately high, 2.8g/$m^2$.day to 7.4g/$m^2$. day(concentration 25.0mg/${\ell}$ to 49.7mg/${\ell}$) for T-N and 1.0g/$m^2$.day to 2.6g /$m^2$.day(concentration 8.6mg/${\ell}$ to 14.7mg/${\ell}$) for T-P, the removal rate of them were 86.5% and 94.0%, respectively. The removal rate by the flow distance increased rapidly in the first 4m from the inlet zone, and gradually there after. The width of system was 2m. Overall, the result showed that constructed wetland system is a feasible alternative for the treatment of wastewater from industrial complex in rural areas. Compared to existing systems, this system is quite competitive because it requires low capital cost, almost no energy and maintenance, and therefore, very cost effective.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.4
• /
• pp.367-372
• /
• 2000

A series of experiment was conducted to investigate the relationship between ammoia removal rate and ammonia loading rates in seawater filtering system using rotating biological contactor (RBC). In this experiment, RBC system was consisted of rotating polyvinyl film disks, which provided $12 m^2$ of total effective surface area in $0.075 m^3$ of volume. $NH_4Cl$ was added by $10{\~}150 g$ as a ammonia nitrogen source to determine ammonia removal rate in RBC system. Relationship between time required for ammonia removal (y: hour) and nitrogen inputted ($x: NH_4-N mg/l$) in RBC system was as followed: $y=3.51+7.76 lnx (r^2=0.936)$. At ammonia concentration $2 mg/l$, it took 10 hour for removal of ammonia in the RBC system. However, at ammonia concentration of $5 and 16.5 mg/l$, it took 16 and 27 hours, respectively. There was a decreasing tencency of an increasing ammonia in the rearing water. Finally, the ammonia removal rate in the RBC system increased with the rise of total ammonia concentration up to $16.5 mg/l$.

• Korean Journal of Environmental Agriculture
• /
• v.18 no.1
• /
• pp.54-60
• /
• 1999

Three different types of lab-scale anaerobic bioreactors, AF and two-stage ASBF-PR and ASBF-SP, were evaluated in treating swine wastewater by operating at $1{\sim}2$ days of hydraulic retention time with increasing organic loading rate upto 6.3 $kg-COD/m^3{\cdot}d$ at $35^{\circ}C$. Seeding the anaerobic bioreactors with waste anaerobic digester sludge from a municipal wastewater treatment plant was effective and a 40-day acclimation period was required for steady-state operation. Three anaerobic bioreactors were effective in treating swine wastewater with COD removal efficiency of $66.4{\sim}84.9$% and biogas production rate of $0.333{\sim}0.796m^3/kg-COD_{removed}{\cdot}d$. Increases of organic loading rate by increasing influent COD concentration and/or decreasing hydraulic retention time caused decreases in COD removal efficiency and increases in biogas production rate. At relatively high organic loading rate employed in this study, the treatment efficiency of AF and ASBF-PR were similar but superior than that of ASBF-SP, indicating that porosity and pore size of the media packed in the bioreactors are more important factors contributing the performance of to bioreactors than specific surface area of the media. TKN in swine wastewater must be removed prior to the anaerobic processes when anaerobic process is considered as a major treatment process since influent TKN concentration of $1,540{\sim}1,870mg/L$ to the bioreactors adversely affect the activity of methanogenic bacteria, resulting in decreases of treatment efficiency and biogas production rate by 50%.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.29 no.2
• /
• pp.230-237
• /
• 1996

The objective of the present study is to evaluate organic removal efficiencies, nitrogen removal efficiencies, kinetic constant, sludge production rates, oxygen requirements, and optimum treatment renditions for recycling water treatment of aquaculture by using a trickling filter process. When the loading rates were $0.500\~0.082kg\;COD/m^3/day$ and $0.271\~0.044kg\;NH_4^+-N/m^3/day$, SCOD and ammonia removal efficiencies were $74.5\~84.0\%$ and $43.7\~61.8\%$, respectively. The maximum removal rate of ammonia was 119.5 mg/L/day. Observed cell yield coefficient in the trickling filter reactor was 0.572 kg VSS/kg $BOD_{rem}$. When the hydraulic loading rate was $6.712\~40.341m^3/m^2/day$, oxygen uptake rate was $1.33\~7.22\;mg\;O_2/L/hr$.