Transactions of the Korean Society of Mechanical Engineers B
/
v.40
no.6
/
pp.397-402
/
2016
To produce adequate electricity in nuclear and thermal power plants, an optimal amount of steam should be supplied to a generator connected to high- and low-pressure steam turbines. A turbine output control device, which is a special steam valve employed to supply or interrupt the steam to the turbine, is operated using a hydraulic servo actuator. In power plants, the performance of servo actuators is degraded by the air generated from the hydraulic system, or causes frequent failures owing to an increase in the wear of the seal. This is due to the seal being burnt as generated heat using the produced compressed air. Some power plants have exhausted air using a fixed orifice, and thus they encounter power loss due to mass flow exhaust. Failures are generated in hydraulic pumps, electric motors, and valves, which are frequently operated. In this study, we perform modeling and analysis of the load-sensing air-exhaust valves, which can be passed through very fine flow under normal use conditions, and exhaust mass flow air at the beginning stage as with existing fixed orifices. Then, we propose a method to prevent failures due to the compressed air, and to ensure the control accuracy of hydraulic servo actuators.
Transactions of the Korean Society of Mechanical Engineers B
/
v.37
no.2
/
pp.171-179
/
2013
The thermodynamic characteristics of a combined cycle applied with a topping cycle such as a trilateral cycle at relatively high temperatures and a bottoming cycle such as an organic Rankine cycle at relatively low temperatures have been theoretically investigated. This is an electric generation system used to recover the waste heat of the exhaust gas from a diesel engine used for the propulsion of a large ship. As a result, when the boundary temperature between the topping and the bottoming cycles increased, the system efficiencies of energy and exergy were simultaneously maximized because the total exergy destruction rate (${\sum}\dot{E}_d$) and exergy loss ($\dot{E}_{out2}$) decreased, respectively. In the case of a marine diesel engine, the waste heat recovery electric generation system can be utilized for additional propulsion power, and the propulsion efficiency was found to be improved by an average of 9.17 % according to the engine load variation, as compared to the case with only the base engine. In this case, the specific fuel consumption and specific $CO_2$ emission of the diesel engine were reduced by an average of 8.4% and 8.37%, respectively.
Journal of the korean Society of Automotive Engineers
/
v.24
no.5
/
pp.98-103
/
2002
이제 카트 정렬과 휠 셋업에 필요한 최적의 변수들을 알아보았다. 실제 세팅은 위에서 언급한 내용 이외에도 많은 것들을 고려하여야 한다. 타이어 접지력의 세팅은 경기장, 날씨, 제품의 불 균일성 등을 고려하여 야 한다. 즉, 어떤 경기장은 코너의 반경이 다른 경기 장 보다 크며 어떤 경기장은 코너가 매우 많기도 하여 세팅을 상황에 맞게 하여야 하는 것이다. 각각의 변수를 세팅할 경우는 중간 값을 취하는 것이 바람직하여 이 중간 값을 취하는 것이 바람직하며 이 중간 값을 각각의 경기장의 특성에 맞추어 변화시키면 되는 것이다. 예를 들면, 접지력이 작게 발생되는 경기장(혹은 매우 추운날씨) 에서는 캐스터를 코기 하여 초기 회전 발생이 용이하게 할 수도 있다. 또한 토우인 값을 크게 하여 타이어가 마찰을 더욱 많이 발생하여 타이어의 온도가 급격히 상승하여 원하는 접지력의 수준에 용이하게 도달할 수 있게 하는 것이다. 그러나 이러한 세팅은 다른 핸들링 문제를 야기할 수 있다는 것을 이해하여야 하며 이러한 문제를 해결하는 또 다른 노력이 필요하게 되는 것이다. 가장 중요한 것은 후륜 내측으로부터는 조종 성능을 향상시키는데 필요한 접지력을 거의 기대하지 못한다는 것이며 마찰이 적게 발생하여 손쉽게 동력 손실을 초래하고 있다는 것이다. 그러므로 회전을 할 경우에도 속도를 낮추어서는 안되며 이렇게 하이야 핸들링이 매우 용이하게 되는 것이다. 그러나 위의 설명에서도 보았듯이 일부 세팅을 변경하면 여러 곳이 그 효과가 나타난다. 예를 들어 후륜의 간격을 변화시키면 카트에서 무게이동 뿐만 아니라 회전 시에 가속이나 감속에 의한 회전 토크의 효과도 달라지게 된다. 특정한 세팅의 변화가 어떻게 작용할 것이라는 확신을 가지고 있다고 할지라도 세팅에서 가장 중요한 것은 주행 기록이다. 여기서 설명되어진 많은 내용이 주행 기록을 향상시키기를 바라는 바이다.간이 육색과 총육색소 함량에는 영향을 미치지 않는 것으로 나타났다. 관능적 특성평가 중 육색과 육즙참출은 대조구와 비교하여 CLA급여 처리구가 유의적인 차이가 없었으나, 근내지방 축적 정도와 전체적인 기호성은 대조구에 비하여 CLA 급여 처리구가 유의적으로 높은 평가를 받았다(p<0.05). 간격은 술 후 1년 후까지도 지속적으로 감소하는 경향을 보였다. 따라서 이 기간동안에는 추적관찰이 필요한 것으로 생각된다.경미하게 나타났으며, 이는 2% 흥국 첨가식이의 섭취로 인한 bromobenzene 대사 및 유해산소 해독의 촉진에 기인되기 때문일 것으로 생각된다.다.과 및 지질과산화억제효과의 순과 일치하였다. 총 flavonoid 함량은 DPPH 라디칼 제거효과에 대한 $IC_{50}$/ 값과 높은 상관관계(r=-0.9924, p<0.01)를 나타내었다.이 우수한 심근보호 효과를 나타내나, 허혈시간이 2시간을 초과하면 심근의 혈역학적 기능과 미세구조의 변화는 중등도의 저온(22∼24$^{\circ}C$)에서 유의하게 악화되었다. 이 같은 결과로 볼 때 심근 허혈시간이 2시간을 초과한다면 심근 온도를 낮추어야 할 것으로 판단된다. 7.2, with 64.0% of office workers having an average level between 6- and 9. The degree of stress was higher for females than males, for unmarried salaried and hot-tempered persons. Those not doing exercise were subject to the highest levels of stress, and those a having sufficient sleep were found to be subject to less stress.
This study was conducted to obtain basic data for the design of cooling system by the test of engine performance of the power tiller being used widely in the rural area. Among the various factors affecting engine performance, the flow rate of cooling water was considered as the major factor in this study. Motoring loss, output, fuel consumption ratio, torque, heat absorption of cooling water, and thermal efficiency were measured and analyzed based on three flow rates of cooling water such as 15, 20, and $25{\ell}/min$. The results obtained were as follows : 1. Motoring loss of the engine was 1.371 kW at 2,200 rpm., and mechanical efficiency was 79.1% at rated output level. 2. Output power of the engine increased with the flow rate of cooling water increased. 3. BSFC was 282.9g/kW-h at the flow rate of $20{\ell}/min$, and the temperature of cooling water at outlet was $80.9^{\circ}C$. 4. There was a little variation of torque of the engine depending on the flow rate of cooling water. 5. Absorption of heat by cooling water was increased with the increase of flow rate. 6. The highest thermal efficiency of 32.3% at the flow rate of $20{\ell}/min$ was observed.
The online fitness industry has experienced rapid growth in recent years, overcoming physical constraints of conventional fitness programs. The COVID-19 pandemic accelerated the trend as social distancing policies were implemented. However, as financial distress of offline gyms worsened, the Korean government implemented the "With-COVID19" policy, which lifted most of the restrictions and regulations on offline gyms, on November 1st, 2021, raising concerns about the loss of drivers for the growth of the online fitness industry. Using regression discontinuity design in time (RDDiT), this study investigates the causal effect of the "With-COVID19" policy on the viewer engagement of online fitness content. Contrary to expectations that viewer engagement would decrease, it increased by 21%. Additionally, subgroup analysis based on opportunity cost reveals heterogeneity, and the high-cost group experienced a greater increase of 32% compared to low-cost group. Based on these findings, the study provides possible mechanisms of the increase, theoretical contributions on using RDDiT in the Information Systems, and practical implications for guidelines on managing online fitness platforms and content in the era of digital transformation.
This study was attempted to improve the thermal efficiency of 6 kW water-cooled diesel engine on power tiller. The engine performance tests were conducted to find out the effect of cooling water capacity of 2700cc, 2800cc, 2900cc, 3000cc, 3100cc on power, brake specific fuel consumption (BSFC), torque, temperature of cooling water and lubricating oil and friction losses of the engine with D. C. dynamometer. The results obtained in the study are summarized as follows: 1. The performance of the engine tested was adequated to Korea Industrial Standard but actual economy power was 10% higher than the labeled rated power of the engine. The BSFC of the engine tested 297.8g/kW-h which is belong a little higher level than hreign products. The temperature of cooling water was $101^{\circ}C$ which is higher than SAE standard ($88^{\circ}C$) 2. The friction losses of engine tested was 3.656 kW at 2200 rpm of rated rpm (piston speed 6.97m/sec) and is higher than those of foreign products. 3. When the cooling water capacity was increased from 2700cc to 3100cc the power output of the engine was increased from 6.7 kW to 7.13 kW at the rate of 6.4% and also the torque of the engine was increased from 28.85 N.m to 30.76 N.m at the rate of 6.39%. 4. When the cooling water capacity was increased from 2700cc to 3100cc, the BSFC was decreased 6.9g/kW-h from 310.9g/kW-h to 304.1g/kW-h, and after one half hour operation with full load, the temperature of cooling water was decreased $13^{\circ}C$ from $101^{\circ}C$ to $88^{\circ}C$ and also the temperature of lubricant oil was decreased $6.4^{\circ}C$ from $76.7^{\circ}C$ to $70.4^{\circ}C$. 5. The mechanical efficiency was increased from 70.08% to 71.08% when the cooling water capacity was increased from 2700cc to 3100cc.
Yoon, Ik Koo;Yun, Seok Kyu;Jun, Ji Hae;Nam, Eun Young;Kwon, Jung Hyun;Bae, Hae Jin;Chung, Kyeong Ho;Moon, Byung Woo
Journal of Bio-Environment Control
/
v.22
no.4
/
pp.366-370
/
2013
The effects of the early tree shapes with renewal by top-working on Y-shaped peach tree, and the influence on the maintaining fruit quantity with gradual renewal of interstock cultivar were determined. In the comparison of the places of top-working tree, top working tree on the inside of the main branch of interstock cultivar had higher graft union rate and branch growth than those of top working tree on the outside. Tree width, basal diameter of shoot, and number of bearing shoots were smaller in top working tree than in replanted tree. Although labor time was not different to control top working tree and replanted tree, labor time was much required to manage top working tree with interstock cultivar. Accumulated fruit production was 2,384 kg/10a in top working tree and 2,025 kg/10a in replanted tree for three years. However, top working tree had no loss of fruits because interstock cultivar of top-working tree had 3,727 kg/10a of fruits. No variation on fruit quality was observed between top working tree and replanting tree. In terms of economic value of top-working tree, labor to manage interstock cultivar, fertilizer price, fruit bagging, and grading and packing price increased. However, fruit production increased, and price of seedling, rental equipment, pulling-out trees, and repairing supporting system decreased. Therefore, gradual renewal of topworking tree has effects on the maintaining fruit quantity, supplementation on fruit loss, and renewal cultivar.
To investigate the factors affecting the transportability of spray droplets, the maximum distance, the effective distance, the ratio of even distribution, and the diameters of particles were measured in accordance with the different pressure levels of power sprayer using 3 hole swath type nozzle, and the results are summerized as follows; 1. The distance of the most dense point from the nozzle was shortened by 0.5 meter with the 100-meter-long hose. The maximum reaching distances were reduced by 1.5 and 1.0 meters for the 13m/m and the 8.5 m/m hoses respectively, and the effective distance were reduced by 0.5 meter for both cases. 2. The effective distance can not be extended beyond 14 meters even if the length of hose is minimized at the rated pump pressure 28 kg/$cm^2$, it was 1 meter longer for 13m/m hose compared to the 8.5m/m one. 3. In case of 13m/m hose, the most dense point can be extended further by 0.5 meter increasing the pump pressure by 8 kg/$cm^2$, and the maximum distance and effective distance were increased by 2.0 and 0.5 meters respectively. There was no significant effect of pressure changes on the transportability in case of 8.5m/m hose. 4. Both the reduction of hose length and the increase of pump pressure influenced in large extent to the atomization effect of droplets. It was noticed that the diameter of droplet is related to the pump pressure and inside diameter of hose. 5. The pressure drop in 100-meter-long and l3m/m hose was 5~7kg/$cm^2$ at the pump pressure range of 25~33kg/$cm^2$, and it is an equivalent of 2% per 10 meter length of hose.
Several research cases using remote sensing methods to analyze changes of storage and dynamics of groundwater aquifer were reviewed in this paper. The status of groundwater storage, in an area with regional scale, could be qualitatively inferred from geological feature, surface water altimetry and topography, distribution of vegetation, and difference between precipitation and evapotranspiration. These qualitative indicators could be measured by geological lineament analysis, airborne magnetic survey, DEM analysis, LAI and NDVI calculation, and surface energy balance modeling. It is certain that GRACE and InSAR have received remarkable attentions as direct utilization from satellite data for quantification of groundwater storage and dynamics. GRACE, composed of twin satellites having acceleration sensors, could detect global or regional microgravity changes and transform them into mass changes of water on surface and inside of the Earth. Numerous studies in terms of groundwater storage using GRACE sensor data were performed with several merits such that (1) there is no requirement of sensor data, (2) auxiliary data for quantification of groundwater can be entirely obtained from another satellite sensors, and (3) algorithms for processing measured data have continuously progressed from designated data management center. The limitations of GRACE for groundwater storage measurement could be defined as follows: (1) In an area with small scale, mass change quantification of groundwater might be inaccurate due to detection limit of the acceleration sensor, and (2) the results would be overestimated in case of combination between sensor and field survey data. InSAR can quantify the dynamic characteristics of aquifer by measuring vertical micro displacement, using linear proportional relation between groundwater head and vertical surface movement. However, InSAR data might now constrain their application to arid or semi-arid area whose land cover appear to be simple, and are hard to apply to the area with the anticipation of loss of coherence with surface. Development of GRACE and InSAR sensor data preprocessing algorithms optimized to topography, geology, and natural conditions of Korea should be prioritized to regionally quantify the mass change and dynamics of the groundwater resources of Korea.
Asia-Pacific Journal of Business Venturing and Entrepreneurship
/
v.16
no.4
/
pp.167-178
/
2021
The purpose of this study is to analyze the direct investment decision factors in the Kaesong Industrial Complex and Vietnam, and to contribute to the creation of domestic jobs and the revitalization of the inter-Korean economy. According to the analysis, most of the Kaesong Industrial Complex and Vietnamese investment companies are entering the complex for the purpose of utilizing cheap labor, cheap factory locations, sales/development of local markets, and bypass export production bases in third countries. This can be divided into production-efficient investors using differences in production price such as labor costs and market-oriented investors to sell and expand the local market, which seems to be consistent with global direct investment patterns such as Nike, Apple, and Amazon. However, even if the North Korea-U.S. denuclearization talks ease or lift sanctions, Vietnamese investors' willingness to invest in the North Korea has been most burdened by the possibility of closing special economic zones due to political risks. Last but not least, it is important to note that those willing to invest in North Korea are mostly smaller enterprises in textiles, sewing, footwear and leather industries-those that benefit from low-cost labor. Since their size is small, they need policy support in financing, especially in the early stages of their business. Even after they grow past the early stages, those without collateral would still need state guarantee letters to get financing. Thus, it is worth considering to use the Inter-Korean Cooperation Fund to compensate commercial banks for bad loan loss or for low-interest loans for smaller SMEs. The interviews with SMEs found that red-tape is one of the biggest difficulties they face. Thus, it is recommended that a one-stop service agency should be established to cover all processes and issues related to inter-Korean economic cooperation to eliminate redundancy and expediate government support for SMEs.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.