• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.5A
• /
• pp.421-431
• /
• 2009

This paper is the study on the verification of structural health monitoring (SHM) algorithm based on the ultrasonic guided wave. An active inspection system using Lamb wave (LW) for SHM was considered. The basic study about the application of this algorithm was performed for detecting the circular notch defect in steel plate. LW testing technique, pitch-catch method, was used for interpretation of circular notch defect with depth of 50% of plate thickness and 7 mm width. Damage characterization takes place by comparing $S_0$ mode sensor signals collected before and after the damage event. By subtracting the signals of both conditions from each other, a scatter signal is produced which can be used for damage localization. The continuous Gabor wavelet transform is used to attain the time between the arrivals of the scatter and sensor signals. A new practical damage monitoring algorithm, based on damage monitoring polygon and pitch-catch method, has been proposed and verified with good accuracy. The possible damage location can be estimated by the average on calculated location points and the damage extent by the standard deviation.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.197-204
• /
• 1993

Abstract The effects of the hole size and the specimen width on the fracture behavior of several fabric composite plates are experimentally investigated in tension. Tests are performed on plain woven glass/ epoxy, plain woven carbon/epoxy and satin woven glass/polyester specimens with a circular hole. It is shown in this paper that the characteristic length according to the point stress criterion depends on the hole size and the specimen width. An excellent agreement is found between the experimental results and the analytical predictions of the modified failure criterion. The notched strength increase with an increase in the damage ratio, which is explained by a stress relaxation due to the formation of damage zone. When the unstable fracture occurred, the critical crack length equivalent for the damage zone is about twice the characteristic length. The critical energy release rate $G_c$ is independent of hole size for the same specimen width. The variation of $G_c$ according to the material system, fiber volume fraction and specimen width relates to the notch sensitivity factor. $G_c$ increases with a decrease in the notch sensitivity factor, which can be explained by a stress relaxation due to the increase of damage zone.

• Composites Research
• /
• v.27 no.6
• /
• pp.219-224
• /
• 2014

Nancomposites manufacture has been developed rapidly, because of reinforcing effects of CNT in terms of mechanical, electrical and thermal properties. In this study, 10 wt% CNT paste was fabricated with good dispersion state and easy processability. Damage sensing and reinforcing effect of CNT paste were investigated in nanocomposites. 10 wt% CNT paste exhibited better tensile and flexural properties than those of general 1 wt% CNT nanocomposites. To observe the healing effect of CNT paste, a crack was made artificially with 30wt% CF30wt%/PP composites, and the CNT paste was filled inside the crack. The damage sensing of CNT paste in CF30wt%/PP composites was investigated by electrical resistance measurement and mechanical tests. CNT paste exhibited good reinforcing effect in mechanical properties of CF30wt%/PP composites, and this reinforcing effect was getting better with larger cracks. The reason was because CNT paste had good interfacial adhesion with CF30wt%/PP composites to resist crack propagation. In electrical resistance measurement, there was a jump in electrical resistance signal at the adhesion interface. The jumping signal could be used to predict fracture of CF/PP composites. CNT nanocomposites for damage sensing had crack reducing effect and damage detection using electrical resistance method.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.17 no.1
• /
• pp.75-94
• /
• 2019

As the present single-layer repository concept requires too large an area for the site of the repository, a multi-layer repository concept has been suggested to improve the disposal density. The effects of the excavation damaged zone around the multi-layer repository constructed in the deep host rock on the temperature distribution in the repository were analyzed. For the thermal analysis of the multi-layer repository, the hydrothermal model was used to consider the resaturation process occurring in the buffer, backfill and rock. The existence of an excavation damaged zone has a significant effect on the temperature distribution in the repository, and the maximum peak temperatures of double-layer and triple-layer repositories can rise to $7^{\circ}C$ and $12^{\circ}C$, respectively depending on the size of the excavation damaged zone and the degree of decrease of the thermal conductivity. The dominant factor affecting the peak temperature in the multi-layer repository is the decrease of thermal conductivity in the excavation damaged zone, and the excavation damaged zone formed around the deposition hole has more significant effects on the peak temperature than does the excavation damaged zone formed around the disposal tunnel.

• Journal of Biosystems Engineering
• /
• v.27 no.3
• /
• pp.211-218
• /
• 2002

배추 생산에 있어서 수확, 운반, 적재 작업은 가장 노동이 집약적으로 요구되는 작업들이다. 최근, 여러 종류의 양배추 수화기가 일본과 유럽에서 개발되었다. 하지만 국내에서 재래되는 배추는 크기와 형태에 있어 양배추와는 달라 기 개발 기종의 도입이 어렵다. 또한 수확작업의 생력화 효과는 운반, 정선, 적재 작업과 밀접하게 연계되어 있어 출하시의 작업체계를 고려하여 수화에 따른 수집.반출 시스템을 개발하여야 한다. 수확시의 배추는 중량이 25~45 N 정도로 다 작물에 비하여 무겁고 부피가 크기 때문에 수확작업의 기계화를 위해서는 수확장치와 더불어 연속적으로 수확되는 배추를 적절하게 수집하여 적재하고 반출하는 시스템의 개발이 중요하다. 본 연구에서는 수확작업의 생력화 효과를 높이고 생력화 시스템 비용의 절감을 목적으로 작업자 1인에 의해 작업할 수 있는 반자동 형태의 트랙터 부착형 배추 수집, 적재, 반출시스템 시작기를 개발하였다. 시작기는 배추 이송장치, 적재장치, 팔렛 및 반출장치의 3개 부분과 PLC를 이용한 주 제어기로 구성하였다. 배추 수집용기로는 대략 70개의 배추를 담을 수 있는 크기가 1,050 mm$\times$1.050mm$\times$1,000mm 인 접이식 메쉬 팔렛을 사용하였으며 하단부에 롤러 안내판을 부착하여 적재한 팔렛의 배출이 용이하도록 하였다. 팔렛을 제외한 전체 시작기의 중량은 235 N 이였으며 크기는 3,940mm$\times$520mm$\times$1,630mm 이었다. 본 연구는 수확장치의 기능 및 생력화 효과를 극대화하고 배추의 손상정도를 최소화하는 시스템을 구성하고자 하였다. 이송장치는 트랙터 부착시 횡공간 점유율을 최소화하도록 하였으며 적재장치는 적재시 배추의 손상을 줄이고 배추가 놓이는 자세를 능동적으로 조절할 수 있도록 주름관을 부착하였다. 시작기의 실내시험 결과 이송장치는 0.18 m/s~0.36 m/s의 범위에서 적재장치는 0.4 m/s~2.4 m/s 범위에서 안정적으로 구동하였으며 두 장치를 동시에 구동하여 시험한 결과 이송장치는 0.26 m/s~0.36 m/s, 그리고 적재장치는 0.9 m/s~2.4 m/s 에서 적정하게 안정적으로 구동하였다. 적재장치의 성능에 있어서 1~3단 적재시에는 주름관을 이용하여 적재하고 4~5단 적재시에는 자유낙하에 의한 적재를 수행할 경우 인력에 의한 적재와 거의 동등한 적재량을 보였으며 손상정도는 거의 무시할 정도였다. 트랙터가 0.3 m/s로 주행하는 경우 노지로부터 배추를 뽑아 이송하는 뽑기벨트의 적정속도가 0.46 m/s인 점을 고려할 때 배추 이송 컨베이어는 0.34 m/s 이상의 속도를 유지할 필요가 있었으며 적재 컨베이어는 2 m/s~2.4 m/s의 속도에서 안정적으로 작동하였다. 배추의 주간 거리가 대략 30~40 cm 인 점을 감안하면 적재장치는 초당 1개의 적재성능을 보였다. 실내에서 수행한 시스템의 성능은 배추에 큰 손상없이 전반적으로 성공적으로 구동하였으나 향후 노면이 고르지 못한 포장에서의 성능 시험이 필요하다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.44 no.2
• /
• pp.141-149
• /
• 2018

The structure of the coacervate can dramatically influence deposition on the hair. The purpose of this study was to investigate the effect of coacervate with a relatively fine and uniform structure on the surface properties of hair and its influence on hair damage. In this study, coacervates of different sizes were explored in 10% shampoo solutions; one solution contained coacervates with non-uniform sizes ($10-300{\mu}m$ average), and the other solution formed a coacervate with a fine and uniform ($1-3{\mu}m$) structure. To study the effect of shampoo on the physical properties of hair and damage to the hair, the hair breakage characteristics, color changes, friction properties, lipid contents and hair surface were examined after using two different types of shampoo. The results clearly show that the relatively fine and uniformly sized coacervate was evenly deposited over the surface of the hair. As a result, the coacervate system can substantially influence the surface properties of the hair such as hair friction, breakage characteristics, and color. The frictional force was dramatically reduced. The use of a fine and uniformly sized coacervate can notably improve hair surface properties. Consequently, hair breakage decreased, and the effect of the coacervate on hair damage was remarkably high.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.308-315
• /
• 2009

Because the attenuation of AE signal in composite materials is relatively higher than that of metallic materials, it is required to develop a damage assessment technique less affected by the attenuation property of composite materials in order to use AE sensing as a damage detection method. In the signal processing procedure, it is profitable to use the leading wave that arrives first because the leading wave is less influenced by the boundary conditions. Using wavelet transform, we investigated the frequency characteristics of impact induced AE signals focused on the leading wave in advance and chose the key factors to discriminate the damaged condition quantitatively. In this research, we established a damage assessment technique using the sharing percentage of the wavelet detail components of AE signal, and conducted a low-velocity impact test on composite laminates to confirm the feasibility of the proposed signal processing method.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.5
• /
• pp.19-27
• /
• 2002

Dynamic responses of a multi-span simply supported bridge are investigated to examine the effect of bearing damage under seismic excitations. The damaged bearings are modeled as sliding elements with friction between the superstructure and the top of the pier. Various values of the friction coefficients are examined to figure out the effect of damaged bearings with various levels of peak ground accelerations. It is found that the global seismic behaviors are significantly influenced by the occurrence of bearing damage. It should be noticed that the most possible location of unseating failure of superstructures differs from that in the bridge model without considering the bearing damage. It can be concluded that the bearing damage may play the major role in the unseating failure of a bridge system, so that the damage of bearings should be included to achieve more rational seismic safety evaluation.

• Journal of the Korean Society of Radiology
• /
• v.84 no.4
• /
• pp.846-854
• /
• 2023

Vascular injuries of the extremities are associated with a high mortality rate. Conventionally, open surgery is the treatment of choice for peripheral vascular injuries. However, rapid development of devices and techniques in recent years has significantly increased the utilization and clinical application of endovascular treatment. Endovascular options for peripheral vascular injuries include stent-graft placement and embolization. The surgical approach is difficult in cases of axillo-subclavian or iliac artery injuries, and stent-graft placement is a widely accepted alternative to open surgery. Embolization can be considered for arterial injuries associated with active bleeding, pseudoaneurysms, and arteriovenous fistula and in patients in whom embolization can be safely performed without a risk of ischemic complications in the extremities. Endovascular treatment is a minimally invasive procedure and is useful as a simultaneous diagnostic and therapeutic approach, which serve as advantages of this technique that is widely utilized for vascular injuries of the extremities.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.269-279
• /
• 2000

It is much expected that steel bridges, which have been damaged by increase of vehicle load and corrosion, need repair or strengthening. In this paper, the stress generated by repair welding under loading are analyzed by three dimensional elasto-plastic analyses. The longer and deeper repair weld line bocemes, the larger the magnitude of transient stress becomes. The magnitude of transient stress generated by repair welding under loading $({\sigma}_y/3,\;{\sigma}_a)$ is similar to summation of stresses generated by repair welding and loading. The longer repair weld line ratio(1/b) becomes, the larger the magnitude of transient stress generated by repair welding under loading bocomes. And, the longer repair weld line ratio(1/b) becomes, the larger the magnitude of in-plane displacement generated by repair welding under loading$({\sigma}_y/3,\;{\sigma}_a)$.