• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.1D
• /
• pp.1-10
• /
• 2010

Safety improvement has been a continuous challenge, especially at toll gate of express highway where traffic conflict often occurs due to frequent lane change by drivers of "Hi-pass" lane and regular "TCS" lane. As a part of research on safety at toll gate, this study videotaped traffic conflict data between vehicles using centrally located "Hi-pass" lane and regular "TCS" lane and analyzed accident risk. According to the correlation analysis of vehicle speed, relative vehicle speed, and sudden vehicle deceleration rate due to traffic conflict, when the relative vehicle speed between centrally located "Hi-pass" lane and regular "TCS" lane increases, sudden vehicle deceleration rate also increases. One of the findings is that centrally located "Hi-pass" lane at toll gate shows different location for traffic conflict, and frequency of traffic conflict and the relative vehicle speed was also different based on vehicle lane use. TA (Time to Accident) analysis shows that accident rate is high at toll gate where Hipass lane is installed in center lane, when the occurrence of sudden vehicle deceleration and deceleration time of vehicles rise for vehicles on "Hi-pass" lane. Furthermore, if the expressway entrance/exit point is closely located to toll gate, TA showed a low value. Thus, it is necessary to reduce the relative vehicle speed in order to improve safety. The Study presents reduction of the relevant vehicular speed and prevention of accidents at the centrally installed "Hi-pass" lane as an important strategy for safety improvement at toll gate.

• The Korean Journal of Air & Space Law and Policy
• /
• v.17
• /
• pp.55-89
• /
• 2003

What are the international aviation regimes? It is said that they are sets of principles, norms, rules, and decision-making procedures of international aviation around which aviation actors' (states-actors, intergovernmental aviation organization, international aviation conventions, airlines and their organizations etc.) expectations converge in a given aviation issue-area for the purposes of the human welfare and the operations of the stable civil aviation. In this regards, the purposes of this study are focused on the aviation actors' shifts. Chronologically, international aviation regimes have been developed by some stages as followings; The 1st stage is the period from 1944 Chicago Convention to 1978 US Deregulation Act, when the aviation regulations and rules within the international aviation relations were implemented by Chicago-Bermuda regimes as Christer Jonsson pointed out. In this first stage, the sovereignty for the airspace over their countries is absolute. The second stage is the period from 1978 to '1992 Open Skies Agreement' between US and Netherlands. In this regime, airlines' activities as well as state-actors' have been actuated. The third stage is the period from 1992 to the contemporary. In this stage, airlines' activities for the consumers such as 'Open Skies Agreements', 'e-commerce business', 'airspace open policy within EU area', 'service open policy of WTO', and 'airlines' strategic alliance' are the central focal points in the world aviation relationship. In the conclusion, this phenomenon of the core actors in the international aviation rules has been shifted from the states-actors to the non-states actors especially, operating airlines, or consuming customers. Finally, I' d like to suggest that international aviation regimes should be developed to promote and facilitate the globalized level for the people's movements among the global aviation society. That is the way to proceed to the welfare and peace for all human beings of the World.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.9 no.1
• /
• pp.119-132
• /
• 2014

This study analyzed the failure prediction model of the firms listed on the KOSDAQ by considering whether there are embezzlement, malpractice and the largest shareholder changes or not. This study composed a total of 166 firms by using two-paired sampling method. For sample of failed firm, 83 manufacturing firms which delisted on KOSDAQ market for 4 years from 2009 to 2012 are selected. For sample of normal firm, 83 firms (with same item or same business as failed firm) that are listed on KOSDAQ market and perform normal business activities during the same period (from 2009 to 2012) are selected. This study selected 80 financial ratios for 5 years immediately preceding from delisting of sample firm above and conducted T-test to derive 19 of them which emerged for five consecutive years among significant variables and used forward selection to estimate logistic regression model. While the precedent studies only analyzed the data of three years immediately preceding the delisting, this study analyzes data of five years immediately preceding the delisting. This study is distinct from existing previous studies that it researches which significant financial characteristic influences the insolvency from the initial phase of insolvent firm with time lag and it also empirically analyzes the usefulness of data by building a firm's fail prediction model which considered embezzlement/malpractice and the largest shareholder changes as dummy variable(non-financial characteristics). The accuracy of classification of the prediction model with dummy variable appeared 95.2% in year T-1, 88.0% in year T-2, 81.3% in year T-3, 79.5% in year T-4, and 74.7% in year T-5. It increased as year of delisting approaches and showed generally higher the accuracy of classification than the results of existing previous studies. This study expects to reduce the damage of not only the firm but also investors, financial institutions and other stakeholders by finding the firm with high potential to fail in advance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.5
• /
• pp.179-184
• /
• 2018

To lessen oxygen concentrations in a wafer through modifying the length of graphite heaters, we investigated the influence of relative distance from heater to quartz crucible on temperature profile of hot-zone in Czochralski silicon-crystal growth by simulation. In particular, ATC temperature and power profiles as a function of different ingot body positions were investigated for five different heater designs; (a) typical side heater (SH), (b) short side heater-up (SSH-up), (c) short side heater-low (SSH-low), (d) bottom heater without side heater (Only-BH), and (e) side heater with bottom heater (SH + BH). It was confirmed that lower short side heater exhibited the highest ATC temperature, which was attributed to the longest distance from triple point to heater center. In addition, for the viewpoint of energy efficiency, it was observed that the typical side heater showed the lowest power because it heated more area of quartz crucible than that of others. This result provides the possibility to predict the feed-forward delta temperature profile as a function of various heater designs.

• Journal of Navigation and Port Research
• /
• v.39 no.3
• /
• pp.199-207
• /
• 2015

In ports of Korea, the marine traffic flow is congested due to a large number of vessels coming in and going out. In order to improve the safety and efficiency of these vessels, South Korea is operating with a Vessel Traffic Service System, which is monitoring its waters for 24 hours. However despite these efforts of the VTS (Vessel Traffic Service) officers, collisions are occurring continuously, the risk situation is analyzed that occurs once in about 20 minutes, the risk may be greater. It investigated to reduce these accidents by providing a safety standard for collision danger in a timely manner. Thus, this study has developed a risk prediction module to predict risk in advance. This module can avoid collision risk to adjust the speed and course of ship using a risk evaluation model based on ship operator's risk perspective. Using this module, the ship operators and VTS officers can easily be identified risks in complex traffic situations, so they can take an appropriate action against danger in near future including course and speed change. To verify the effectiveness of this module, this paper predicted the risk of each encounter situation and confirmed to be capable of identifying a risk changes in specific course and speed changes at Busan coastal water.

• Atmosphere
• /
• v.15 no.2
• /
• pp.75-90
• /
• 2005

This study examines the impacts of land cover changes on the East Asia summer monsoon with the National Center for Atmospheric Research Regional Climate Model (NCAR RegCM2), coupled with Biosphere Atmosphere Transfer Scheme (BATS). To assess the goals, two types of land cover maps were used in the simulation of summer climate. One type was NCAR land cover map (CTL) and the other was current land cover map derived from satellite data (land cover: LCV). Warm and cold surface temperature biases of $1-3^{\circ}C$ occurred over central China and Mongolia in CTL. The model produced excessive precipitation over northern land area but less over southern ocean of the model domain. Changes of biophysical parameters, such as albedo, minimum stomatal resistance and roughness length, due to the land cover changes resulted in the alteration of land-atmosphere interactions. Latent heat flux and wind speed in LCV increased noticeably over central China where deciduous broad leaf trees have been replaced by mixed farm and irrigated crop. As a result, the systematic warm biases over central China were greatly reduced in LCV. Strong cooling of central China decreased pressure gradient between East Asian continent and Pacific Ocean. The decreased pressure gradient suppressed the northward transport of moisture from south China and South China Sea. These changes reduced not only the excessive precipitation over north China and Mongolia but also less precipitation over south China. However, the land cover changes increased the precipitation over the Korean Peninsula and the Japan Islands, especially in July and August.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.47-53
• /
• 2020

The purpose of this study was to increase product reliability by improving the durability of the breech block for a 30mm Automatic Gun. The breech block is a key component of a gun that functions as chambering, closing, and extracting. The breech block requires high reliability, which needs to be improved because cracks of a breech block can occur early in operation. Cause analysis confirmed that the crack is caused by repeated impacts. Therefore, the following improvement measures were studied, and the effects were demonstrated using a firing test. The energy of impact absorption was increased by changing the material, and the stress concentration was mitigated by increasing the value of R. In addition, the fatigue life was increased by adding Shot-peening, deleting chromium plating, and changing the forging method. The firing test did not show firing trouble for up to 5,000 rounds. The start timing of the crack was delayed, and the depth was small. Therefore, the improved product was more durable than the existing product. This study can be used as a useful reference when assessing the improvement of the durability of similar products, life study, and criteria for crack acceptance.

• The Journal of the Korea Contents Association
• /
• v.20 no.9
• /
• pp.672-680
• /
• 2020

This study aimed to elucidate the differences in nursing service experience according to the participants' characteristics and experience of hospitalization and to identify the relation between nursing service experience and perceptions of the health system. It analyzed the data from a "Survey of health care service experience" conducted among 574 participants who had been hospitalized. The results showed that the mean nursing service experience of participants who had never used other hospitals before hospitalization with over ten days of hospital stay was higher compared with the other participants. Moreover, those who used other hospitals before hospitalization reported lower nursing service experience scores. In the classification based on the change of the inpatient room, the difference in the nurse service experience according to the number of hospitalization days was significant only in patients who had no change in the inpatient room in the multi-person room. The nursing service experience scores were positively related to general satisfaction with the hospitalization experience, health system satisfaction, and trust in the health system. This finding implies that the nursing service experience should be interpreted by separating the inpatient experience, and the strategies to improve the nursing service are needed. In addition, the survey should include items related to the characteristics of medical institutions such as nurse staffing, to identify factors affecting the experience of nursing services.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.85-85
• /
• 2011

홍수기에 안전하고 정확한 유량측정을 통하여 물관리에 필요한 기초수문자료를 확보하고자 한국수자원공사에서 1993년도부터 홍수유량측정기술 확보를 위한 연구를 시작하였다. 그간의 연구성과를 바탕으로 1999년도에 하천의 유속을 비접촉식으로 측정할 수 있는 홍수용 전자파표면유속계를 개발하여 특허등록하였고 그와 동시에 이의 상품화를 추진하여 2010년도까지 75대를 보급하여 실무에서 이용하고 있다. 이동식인 홍수용 전자파표면유속계를 바탕으로 2001년도에는 고정식 실시간 홍수유량측정측정시스템을 개발하여 특허등록하였고, 이 시제품을 현재 용담 수자원시험유역의 동향지점에서 시험운영하고 있다. 또한, 현장 유량측정실무자들의 홍수용 전자파표면유속계 개선요구에 따라 편각용 전자파표면유속계 시제품을 개발하였으며, 이는 임의의 한 지점에 설치한 한 대의 장비로 좌우 여러 측선의 유속을 동시에 측정할 수 있는 다점 측정기능을 갖도록 성능을 개선하였다. 이에 따라 홍수시 유량측정에 소요되는 시간이 줄어들어 신속하게 유량측정을 완료할 수 있는 계기를 마련하였다. 이와 더불어 유속측정 범위를 확장하여 홍수시의 고유속 뿐만 아니라 0.5 m/s 이하의 저유속까지 측정할 수 있는 범용 전자파표면유속계의 시제품을 추가로 개발하였다. 이 장비는 최저유속 0.03 m/s의 측정을 실내시험을 통하여 입증하였다. 범용 전자파표면유속계는 상품화 시제품의 개발을 목표로 기존 시제품의 현장시험을 통하여 현장적용상의 문제점에 대한 해결에 주력하였다. 첫째, 평갈수용 전자파표면유속계의 사용편의를 개선하기 위하여 소형화 및 경량화를 추진하였고, 이를 위하여 사용주파수를 기존의 10 GHz에서 24 GHz로 변경함으로써 $35{\times}35\;cm$ 크기의 기존안테나를 $22{\times}22\;cm$ 크기로 소형화하였으며 송수신부의 무게는 기존 18 kg에서 3.3 kg으로 혁신적으로 줄이는데 성공하였다. 이를 위하여 안테나는 기존의 반사형안테나에서 도파관슬롯배열안테나로 변경하였다. 둘째, 측정값의 안정화를 위하여 안테나의 특성을 개선하여 부엽(side-lobe) 레벨 30 dB 이하 그리고 전후방비(front-back ratio) 50 dB 이하로 개선하여 안테나가 지향하는 방향 이외의 위치에서 반사되는 불필요한 신호를 줄였다. 또한 적응형 이득제어(adaptive gain control)기법의 채택으로 미소 신호에 대한 안정적 측정 및 과다 신호에 대한 능동적 감쇄를 할 수 있도록 시스템을 구성하여 전 유속범위에 대한 안정적 측정을 가능토록 설계 및 제작하였다. 셋째, 자가점검 기능을 탑재하여 유속측정 전에 기기의 상태에 대한 self test기능을 통하여 측정자가 기기의 상태를 사전에 파악 가능토록함으로써, 기기 오작동에 대한 능동 대처할 수 있도록 하였다. 이외에도 저전력 회로설계를 통하여 배터리 사용시간을 확장하였고, 기존의 전자파표면유속계가 가지고 있던 방습 및 방수에도 내성을 갖는 제품으로 설계하였으며 스마트기기를 이용한 무선측정 및 세련된 디자인 등 사용자의 요구사항을 충분히 반영하였다.

• The KIPS Transactions:PartD
• /
• v.15D no.6
• /
• pp.755-766
• /
• 2008

Recently, NAND flash memory is becoming into the spotlight as a next-generation storage device because of its small size, fast speed, low power consumption, and etc. compared to the hard disk. However, due to the distinct characteristics such as erase-before-write architecture, asymmetric operation speed and unit, disk-based systems and applications may result in severe performance degradation when directly implementing them on NAND flash memory. Especially when a B-tree is implemented on NAND flash memory, intensive overwrite operations may be caused by record inserting, deleting, and reorganizing. These may result in severe performance degradation. Although ${\mu}$-tree has been proposed in order to overcome this problem, it suffers from frequent node split and rapid increment of its height. In this paper, we propose Log-Structured B-Tree(LSB-Tree) where the corresponding log node to a leaf node is allocated for update operation and then the modified data in the log node is stored at only one write operation. LSB-tree reduces additional write operations by deferring the change of parent nodes. Also, it reduces the write operation by switching a log node to a new leaf node when inserting the data sequentially by the key order. Finally, we show that LSB-tree yields a better performance on NAND flash memory by comparing it to ${\mu}$-tree through various experiments.