• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.567-570
• /
• 2008

The present study investigated the applicability of the minium fludization velocity measuring method using linear regression analysis between the standard deviation of pressure fluctuation and gas velocity in multi-particle sand on a fluidized bed 0.109 in inner diameter. We measured minium fludization velocity according to the standard deviation of particle distribution in Gaussian distribution. The measured value compared with other researchers' equations. The minium fludization velocity derived from the linear regression analysis of the standard deviation of pressure fluctuation and pressure drop inside the bed. We also found that the minium fludization velocity of a multi-particle system using the standard deviation of pressure fluctuation must be measured at freely bubbling region.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.159-166
• /
• 2009

On freeways, factors inducing traffic accidents consist of two major elements such as driver factors and road environment factors. Research have been done and shown that there would be relationship between design elements such as radius, slopes, superelevations, and observed speeds and accident rates. The present paper confirms that these elements are correlated with accident rates. Furthermore, the paper identifies standard deviation of these elements as the design consistency and compare them with reduction of accident rates. This type of work leads to identify the fact that standard deviations based design consistency are correlated with accident rates. The results of the paper may contribute to encourage the quantified use of design consistency during highway design.

• Journal of Korean Society of Transportation
• /
• v.29 no.4
• /
• pp.103-111
• /
• 2011

The speed is one of the significant factors affecting accident occurrence. In particular, freeway accidents are highly associated with the speed because vehicles travel on the freeway at higher speed leading to greater potential of severer injury. Efforts attempting to relating speed with accident occurrence have not been significantly made in Korea. The objective of this study is to model the relationship between speed and accident rate on freeways. Loop detector data and accident data obtained from a stretch of Kyungboo freeway during the recent five years, 2005-2009, were used to establish the model. Multiple linear regression analyses showed that median, minimum and standard deviation of speed were contributing variables in the model. The statistical significance identified by the analyses supports the feasibility of the model in evaluating various transportation policies and operations strategies in terms of traffic safety.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.12
• /
• pp.1186-1192
• /
• 2008

The reliability of gas turbine engine blades was studied. Yield strength, Young’s modulus, engine speed and gas temperature were considered as statistically independent random variables. The failure probability was calculated using five different methods. Advanced Mean Value Method was the most efficient without significant loss in accuracy. When random variables were assumed to have normal, lognormal and Weibull distributions with the same means and standard deviations, the CDF of limit state equation did not change significantly with the distribution functions of random variables. The normalized sensitivity of failure probability with respect to standard deviations of random variables was the largest with gas temperature. The effect of means and standard deviations of random variables was studied. The increase in the mean of gas temperature and the standard deviation of engine speed increased the failure probability the most significantly.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.200-205
• /
• 1996

Recently, in order to achieve high flexibility of manufacture, monitoring and control strategies cf a new type have been developed. Since the generation of built-up edge on the cutting tool damages the surface finish of the workpiece, the monitoring system of built-up edge is an important process monitoring. In this study, the analyzing methods of cutting force signal to detect the built-up edge during cutting process are described. The cutting force signals are analyzed using the mean, standard deviation and mean to standard deviation of this cutting signals. We can obtain the guide to detect the built-up edge during turning process.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.7
• /
• pp.67-72
• /
• 1997

Recently, in order to achieve high flexibility of manufacture, monitoring and control strategies of a new type have been developed. Since the generation of built-up edge on the cutting tool damages the surface finish of the workpiece, the monitoring system of built-up edge is an important process monitoring. In this study, the analyzing methods of cutting force signal to detect the built-up edge during cutting process are described. The cutting force signals are analyzed using the mean, standard deviation and mean to standard deviation of this cutting signals. We can obtain the guide to detect the built-up edge during turning process.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.5
• /
• pp.75-82
• /
• 2021

The number of traffic accidents is about 230,000, and due to non-recurring congestion and high driving speed, the number of deaths per traffic accident on freeways is more than twice compared to other roads. Currently, traffic information is provided based on nodes and links using the centerline of the road, but it does not provide detailed speed information. Recently, installing sensors for vehicles to monitor obstacles and measure location is becoming common not only for autonomous vehicles but also for ordinary vehicles as well. The analysis using large-capacity location-based data from such sensors enables real time service according to processing speed. This study presents an mapping method for individual vehicle data analysis based on space. The processing speed of large-capacity data was increased by using method which applied a quaternary notation basis partition method that splits into two directions of longitude and latitude respectively. As the space partition was processed, the average speed was similar, but the speed standard deviation gradually decreased, and decrease range became smaller after 9th partition.

• The Journal of the Korea Contents Association
• /
• v.21 no.12
• /
• pp.302-309
• /
• 2021

The section speed enforcement system measures the starting instantaneous speed, the The section speed enforcement system measures the starting instantaneous speed, the ending instantaneous speed, and the section average speed, and imposes fines only for the portion that has been speeding the most. However, according to the Road Traffic Act, most of the systems are installed on highways, so existing research has been conducted on highway sections. In this study, it is expected that the installation of section speed enforcement systems on general national roads will be expanded according to the revision of related laws. ITS collection and operation data targeting the section speed enforcement system installed on National Road 3 Seongnam Icheon-ro was used to analyze traffic speed, standard deviation of traffic speed, and reduction in traffic accidents by dividing it into before installation, trial operation period, and after crackdown. As a result of the analysis, the traffic speed, standard deviation, and traffic accidents decreased by 13%, 25%, and 70%, respectively, after installation, confirming that the installation of the section speed enforcement system greatly contributed to the reduction of accidents.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.6
• /
• pp.462-469
• /
• 1988

Choromatic dispersion of single mode optical fibers limits the maximum bit rate in the single mode optical transmission systems. In this paper we calculate chromatic dispersion and dispersion parametes(zero dispersion wavelength, dispersion slope) for concatenated single mode optical fibers form the chromatic dispersion and dispersion parameters of individual single mode optical fibers, and compare theoretical valuse with those measrued by double demodulation method. Calculated values are coincident with measured ones reasonably. The standard deviation is 0.77-1.28nm for zero dispersion wavelength and 0.56-0.75PS/km.nm2 for dispersion slope. The standard deviation of zero dispersion wavelength is inverse proportional to the optical fiber lenght.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.1
• /
• pp.16-26
• /
• 2011

Variable speed limit(VSL) is one of the highway ITS techniques designed to prevent accidents and traffic slow down by reducing congestion or speed variation between vehicles and lanes prior to arrive at the accident location by limiting speed. In Korea, while people have recognized the need for variable speed limit beginning with Seoul's urban expressway and installed facilities in order to provide guide for speed limit per lane and lane use, there has not been enough development of algorithm for internal administration as well as research on the basic principles behind administering variable speed limit. This study is for modeling and evaluating the VSL strategies based on the traffic flow theory. Supply-Demand method of the Cell Transmission Model is applied to demonstrate the traffic features and shockwaves to upstream of the bottleneck with/without VSL. We verified the explanation of Cell Transmission Model for the numerical example. and as the result, it is found that VSL strategies can reduce the total travel time in the congested section and variation of the speed. It means VSL is useful to improve the traffic condition and the safety on highway