• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.397-402
• /
• 2001

In this study, the ISO 10534-2 "Determination of sound absorption coefficient and impedance in impedance tubes - Part 2： Transfer function method" was precisely reviewed in order to make it as a new Korean Industrial Standard of KS F 2814-2. Several main contents are experimently tested and discussed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.11
• /
• pp.1071-1077
• /
• 2010

The reduction of the vehicle interior noise has been the main interest of noise and vibration harshness(NVH) engineers. A passenger vehicle has various and complicated transmission paths of sound and vibration. In order to identify the mechanism of transfer path, estimation of excitation force and exact modeling of transfer path are required. This paper presents method for estimating the noise source contribution on the road noise of the vehicle in a multiple input system where the input sources may be coherent with each other. And vector synthesis technique is employed to identify the characteristics of road noise and its transmission to vehicle compartment through noise and vibration analysis. Vibration reduction efficiency of each transfer path is evaluated by comparing individual vector components obtained virtual simulation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.641-642
• /
• 2011

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.377-383
• /
• 2011

This paper reports the filtered velocity feedback (FVF) controller to reduce the acoustic power from clamped beams. The instability problem due to the non-collocated sensor/actuator configuration when using PZT actuator should be resolved. The roll-off property of the FVF controller at high frequency helps to alleviate the instability. The dynamics of clamped beams under forces and moments pair and the FVF controller are first formulated. The formulation of the sound radiated power is followed. The open loop transfer function (OLTF) synthesized with 100 modes is used to determine the stability of the control system. The control performance is finally estimated. The levels of the vibration and the sound radiated power are reduced in the wide band below the tuning mode of the FVF controller.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.1195-1201
• /
• 2002

Researches on the FRF-based substructuring method have been mainly focused on vibratory response analysis. Present study Is concerned about the application of the method to the dynamic stress analysis of a air-conditioner compressor mounting bracket in a passenger car. This is performed by using reaction forces that can be obtained by the FRF-based substructuring method. The air-conditioner system, composed of a compressor and bracket, Is analyzed by using the FRF-based substructuring method. The experimental and numerical FRFs are combined to calculate the system responses and reaction forces at the connection point. The dynamic reaction forces plugged into the bracket FE model to compute the stresses of the bracket Dynamic strains by the present method are compared with those from strain-gage test for bracket system on shaker. The comparison shows possibility of practical usage of the method for the real problem

• Journal of KSNVE
• /
• v.9 no.5
• /
• pp.943-948
• /
• 1999

This paper proposes a feasible and effective method for measuring the mechanical-acoustic transfer function by the application of equivalent area and velocity transfer function, a manifestation of the vibro-acoustical reciprocity principle. On the contrary to the volume velocity used in traditional method, the equivalent area is a peculiar raidation characteristics of sound sources and not influenced by any input signal for driving sound source. This invariant property of equivalent area can get rid of boresome works to measure the volume velocity of a sound source every time the driving signal is changed. Moreover, this method has a remarkable advantage to use a general loudspeaker as an accoustic exciter without the assumption of point source and can be applied to all kinds of sound sources even if they are not omni-directional sources.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.712-712
• /
• 2014

본 논문에서는 지연-가중-합 빔형성 방법이 적용된 지향성 헤드폰의 마이크로폰 배치 설계를 설명한다. 마이크로폰의 갯수, 마이크로폰 간의 간격 등이 헤드폰 지향성에 영향을 미치는 설계 변수가 된다. 본 논문에서는 현실성을 고려하여 4개 이하의 마이크로폰을 포함한 10cm 길이의 배열을 타겟으로 한다. 전방으로부터의 소리를 증폭하고 후방으로부터의 소리를 감쇠하여, 전-후방 음압차를 최대화하는 것을 목표로 하였다. 구형 머리전달 함수를 이용한 시뮬레이션을 통해 최적의 마이크로폰 배치를 결정하였다. 설계된 헤드폰은 3개의 마이크로폰을 이용하여 300~3000Hz의 주파수 대역에서 평균 34.6dB의 전-후방 음압차를 보였다. 이 결과는 선행 연구에서 수행된 지연-합 빔형성 방법을 이용한 결과에 비해 8.8dB 뛰어난 성능이다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.141-145
• /
• 2014

A minimally appropriate time delay of audio data processing is investigated for rendering virtual sound source direction in real-time head-tracking environment under headphone listening. Less than 3.7 degree of angular mismatch should be maintained in order to keep desired sound source directions in virtually fixed while listeners are rotating their head in a horizontal plane. The angular mismatch is proportional to speed of head rotation and data processing delay. For 20 degree/s head rotation, which is a relatively slow head-movement case, less than total of 63ms data processing delay should be considered.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.283-288
• /
• 2006

This study developes the vibration model to estimate the vibration energy of damper/spring assembly(mainbase assembly) for car CD player, and this model is verified by experiment. From frequency response, response, we investigate the natural frequency and mode shape in the up/down direction. In order to determine the analysis frequency band, we investigate the excitation frequency from the vehicle test. As the characteristics of damper and spring is changed, we carry out the vibration test(transmissibility) and investigate the change of transmissibility.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.114-119
• /
• 2003

In this paper, the experimental design of an intake system was studied using the two microphones method and the taguchi method. The transmission loss was utilized to represent the performance of noise reduction for the intake system which was estimated by measuring sound power at inlet and outlet with two microphones, respectively. Two microphones method used in this paper was followed by wave decomposition theory The robust designing parameters of an intake system were extracted by adapting a cost function with the taguchi method, which optimized the process. Finally the effectiveness of the propose method was validated with the experimental data.