• Journal of Korean Society of Steel Construction
• /
• v.23 no.4
• /
• pp.405-415
• /
• 2011

For the safe seismic design of buildings, it is necessary to predict the plastic deformation demands of the members as well as the story drift ratio. In the present study, a simple method of estimating the beam plastic rotation was developed for special-moment-resisting steel frame structures designed with strong column-weak beam behavior. The proposed method uses elastic analysis rather than nonlinear analysis, which is difficult to use in practice. The beam plastic rotation was directly calculated based on the results of the elastic analysis, addressing the moment redistribution, the column and joint dimensions, the movement of the plastic hinge, the panel zone deformation, the gravity load, and the strain-hardening behavior. In addition, the rocking effect of the braced frame or core wall on the beam plastic rotation was addressed. For verification, the proposed method was applied to a six-story special-moment frame designed with strong column-weak beam behavior. The predicted plastic rotations of the beams were compared with those that were determined via nonlinear analysis. The beam plastic rotations that were predicted using the proposed method correlated well with those that were determined from the nonlinear pushover analysis.

• Journal of the Korea Concrete Institute
• /
• v.22 no.6
• /
• pp.825-832
• /
• 2010

Although a critical section reaches its flexural strength in reinforced concrete structures, the structure does not always fail because moment redistribution occurs during the formation of plastic hinges. Inelastic deformation in a plastic hinge region results in plastic rotation. A plastic hinge mainly depends on material characteristics. In this study, a plastic hinge length and plastic rotation are evaluated using the flexural curvature distribution which is derived from the material models given in Eurocode 2. The influence on plastic capacity the limit values of the material model used, that is, ultimate strain of concrete and steel and hardening ratio of steel(k), are investigated. As results, it is appeared that a large ultimate strain of concrete and steel is resulting in large plastic capactiy and also as a hardening ratio of steel increases, the plastic rotation increases significantly. Therefore, a careful attention would be paid to determine the limit values of material characteristics in the RC structures.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.2 s.35
• /
• pp.221-232
• /
• 1998

This study presents a fatigue line with a plastic rotational angle to a great extent of plastic strain of Low-Cycle-Fatigue period, such as earthquake, etc. This fatigue line with a plastic rotational angle is measured and analysed more simply in practice rather than Woehler's fatigue line which is developed in stress variation of the structure. It shows that the slope of fatigue line with a plastic rotational angle is equal to that with plastic strain through the experiments by proving the correlation that the plastic strain ratio is directly proportional to the plastic rotational angle in plastic hinge. The theory is induced by Manson and Coffin strain fatigue line, and the experiments are tested by ECCS. The location of the plastic hinge is achieved and accurate plastic strain ratio is calculated through FEM.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.04a
• /
• pp.163-178
• /
• 1997

현재 각종 미사일의 추진기관용 연소관을 제작하는데 광범위하게 이용되고 있는 유동성 형공정에 대하여 강소성 구성방정식을 이용 유한요소해석을 수행하였다. 종전의 단일 롤러에 의한 해석과는 달리 3개의 롤러에 의한 연소관의 점진 소성변형을 고려하였으며. 이에 따른 각 룰러의 연소관에 대한 소성변형, 응력분포가 관찰, 분석되었다. 해석 결과 예비성형체의 두께에 따라 소성변형 형태와 그에 따르는 응력분포에 많은 차이가 나는 것으로 밝혀졌다. 또 이상적인 유동성형 공정조건하에서 반경 방향으로의 연소관의 유효 소성변형도는 거의 균일하게 나타났다.

• The Korean Journal of Rheology
• /
• v.7 no.2
• /
• pp.128-138
• /
• 1995

본 논문에서는 전단띠형성에 있어서 전단변형의 집중화 현상을 이방성 탄소성 재료 에 대해서 해석하였고 소성스핀과 비등방성이 전단띠 형성에 미치는 영향을 연구하였다. 평 면응력 상태에서 소성스핀을 갖고있는 이방성 탄-소성 재료에 대해서 재료 분랑ㄴ정 해서 을 수행하여 변형률 집중화의 시작에 미치는 소성스핀과 비등방성의 효과를 연구하였다. 해 석 결과 이방성 재료에서의 전단띠 형성은 압축 또는 인장의 하중 형태나 이방성 축의 초기 각도 그리고 소성스핀의크기에 따라 그 시작이 촉진되거나 지연되었고 전단띠 생성의 방향 도 달라졌다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.5
• /
• pp.51-60
• /
• 2009

To secure the structural safety of structures and members against earthquakes, the plastic deformation capacity demand of members should be accurately predicted. In the present study, a method for the evaluation of the plastic deformations of members for moment frames was developed. To facilitate the practical use of the proposed method in equivalent seismic design, the plastic deformations of members were evaluated based on the results of elastic analysis, without using nonlinear analysis. The plastic deformation demands of members were formulated as functions of story drift demand, redistributed moment and member stiffness. Story drift demand and moment redistribution were directly determined from elastic analysis. The proposed method was applied to an 8 story-2 bay moment frame, and the predicted plastic deformations were verified using nonlinear analysis. The results showed that the proposed method could be used to accurately predict the member plastic rotations with simple calculations. The proposed method can be applied both to the earthquake design of new structures and to the performance evaluation of existing structures.

• Journal of the Society of Disaster Information
• /
• v.10 no.1
• /
• pp.25-32
• /
• 2014

The main objective of materials testing is to simulate in-situ field conditions as closely as possible, including loading conditions, climatic conditions, etc. Also, the test method should be easy, inexpensive, simple, and efficient to conduct to become an acceptable standard laboratory testing method for many agencies. Based on these reasons, a new test method employing repetitive axial loading with confinement was developed to evaluate the rutting(permanent deformation) of asphalt concrete. The new laboratory test protocol was developed based on the study of the various structural analysis and field data. This protocol divides asphalt layer(s) into three categories depending upon the depth. Different temperatures and vertical stress levels were used in these areas.

• Journal of the Korea Concrete Institute
• /
• v.26 no.4
• /
• pp.555-562
• /
• 2014

To perform performance-based seismic design of buildings, it is necessary clear goal for usage and stability after an earthquake. To clear this goal, it requires a review of the constituent material of the building and, in particular, a member used as an indicator of the residual strain is useful. There are more usage of prestressed concrete because of prestressing steel witch has characteristics of the origin-oriented. In this study, the goal is estimating of residual strain on the prestressed concrete beam member. The expression for angle of deformed prestressed concrete beam member was obtained from using of curvature on the critical section and the equivalent plastic hinge length based on 'equivalent plastic hinge length method'. Considering the balance of strength and deformation conditions, suitable analysis values were derived from 'split Element Method'. Through various parametric studies, various factors affecting the residual strain were decided. Based on the results of this study, it is expected many researches will be proceed in the future.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.235-240
• /
• 1996

본 연구에서는 고온의 천이 열하중을 받는 304 SS 재질의 액체금속로 원통용기에 대하여 진행성 변형기구인 열적 라체팅(thermal ratcheting) 변형거동을 해석하였다. 재료의 반복 소성을 나타내는 구성식으로서 Chaboche모델을 이용하였으며 이 모델의 적용을 위하여 ABAQUS의 사용자 프로그램을 개발하였다. 열천이 과정이 반복되는 동안에 축방향의 온도분포 이동에 따른 탄소성 해석을 수행한 결과 소성변형이 각 싸이클마다 누적되어 점진적 변형이 일어났으며 이 해석결과를 시험치와 비교함으로써 해석의 타당성을 검토하였다. 반복 소성거동에 대한 Chaboche 모델을 이용하면 천이 열하중을 받는 304 SS. 재질의 고온구조물에 대하여 라체팅 거동을 정량적으로 평가 할 수 있는 것으로 나타났다.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.20-25
• /
• 2002

본 논문은 대 변형 굽힘에 의한 소성 모멘트의 계산시 ovality를 고려한 파이프의 중립축에 대한 모멘트에 관해 논한다. 기존의 계산방법에 의한 중립축에 대한 모멘트 계산결과와 새로운 방법에 의한 계산결과를 비교해 보았다. 파이프가 길이방향의 모멘트에 의하여 굽어질 때, 증가하는 모멘트에 따른 ovality 변화를 고려하여 중립축에 대한 모멘트 계산에 적용해 보았다. 모멘트 계산은 타원형의 파이프 단면을 미세한 단면으로 나누어서 각 단면에 대한 응력을 비선형 strain-stress 식을 이용하여 구한 다음 중립축에 대해 계산을 수행하였다. 대 변형 굽힘에서 일어나는 실제현상 중 하나인 ovality를 파이프의 계산에 적용함으로써 좀 더 정확한 중립축에 대한 모멘트를 계산할 수 있었다. 이 방법을 reel에 의한 해저배관의 설치 공법에서 사용되는 reverse bending radius 계산에 적용해 보았다.