• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.915-920
• /
• 2004

The main phase of $BaTi_{4}O_9$-based ceramics was transformed to $BaTi_{5}O_{11}$ caused by the sintering with borosilicate glass, which was analyzed by using XRD and TEM. We considered that the phase change from $BaTi_{4}O_9$-based ceramics to the Ti-rich $BaTi_{5}O_{11}$ phase resulted from borosilicate glass selective absorbing of Ba ions from the $BaTi_{4}O_9$. In these results, we found a dependence on the amounts of the glass frits and the annealing temperature, and the phase change is also dependent of the main phases of $Ba_{4}Ti_{13}O_{30},\;and\;Ba_{2}Ti_{9}O_{20}$, which are involved in the $BaO-TiO_2-based$ Ti-rich region. In the case of sintering of middle- and high- permittivity material with additional glass frits for middle- and high- dielectric coefficients LTCC composition, control of weight fraction of the glass frits accompanying low-temperature sintering property with appropriate phase change is required.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.233-240
• /
• 2000

In order to fabricate dense cordierite ceramics without sintering aid, thermal behavior of Mg-Al-Si compounds during sintering was investigated. The dispersibility of cordierite suspension in aqueous media was measured by ESA(electrokinetic sonic amplitude). To prevent aggregation and insufficient dispersion of the cordierite sol, the pH of the suspension was controlled to 1.03 and 8.30 by adding $2N\;HNO_3$ and $2N\;NH_4OH$, respectively. Magnesium-aluminum-silicate complex gel coexisted in the specimen which has been gelled at $150^{\circ}C$ fir 12 hours, however several metastable phase such as ${\mu}-cordierite(Mg_2Al_4Si_5O_{18}),\;spine(MgAl_2O_4)\;and\;mullite(Al_6Si_2O_{13})$ existed below $1300^{\circ}C$ Nucleation rates of the two suspension were similar, but densification of the gel was sensitive to the pH of the sol. Densification of the sol with the pH of 8.3 was more pronounced than that of the sol with pH of 1.63.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.3
• /
• pp.135-141
• /
• 2013

Mechanical alloying was carried out to produce $CrSi_2$ thermoelectric compound using a mixture of elemental $Cr_{33}Si_{67}$ powders. An optimal milling and heat treatment conditions to obtain the single phase of $CrSi_2$ compound with fine microstructure were investigated by X-ray diffraction and differential scanning calorimetry measurement. $CrSi_2$ intermetallic compound with a grain size of 70 nm could be obtained by MA of $Cr_{33}Si_{67}$ powders for 70 hours and subsequently annealed at $650^{\circ}C$. Consolidation of the MA powders was performed in a spark plasma sintering (SPS) machine using graphite dies at $600{\sim}1000^{\circ}C$ under 60 MPa. The shrinkage of MA samples during SPS consolidation process increased gradually with increasing temperature up to $1000^{\circ}C$ and relatively significant at about $600^{\circ}C$. We tend to believe that these behaviors are deeply related to form a $CrSi_2$ compound during heating process, as can be realized from the DSC measurement. Electrical conductivity and Seebeck coefficient of sintered bodies were measured up to $900^{\circ}C$. Seebeck coefficient and power factor of $Cr_{33}Si_{67}$ compact prepared by MA and SPS at $1000^{\circ}C$ showed the maximum value of $125{\mu}V/K$ at $400^{\circ}C$ and $4.3{\times}10^{-4}W/mK^2$ at $350^{\circ}C$, respectively.

• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.34-40
• /
• 2000

The $Pb_{0.94}Y_{0.04}[(Zr_{0.6}Sn_{0.4})_{0.915}Ti_{0.085}]O_3$ ceramics which corresponded to the antiferroelectric-ferroelectric phase boundary composition were prepared for digital-type-piezoelectric/electrostrictive device application. Their dielectric, field-induced polarization (P) and strain (X) behaviors were studied with variations in sintering condition and excess PbO content. The orthorhombic structure of specimens was hardly affected either by excess PbO addition or sintering temperature. With increasing excess PbO content, grains tended to be smaller and rounded ones, and the optimum sintering temperature was lowered. Excess PbO addition stabilized the antiferroelectric phase of the specimen effectively, which was confirmed by P-E and X-E analyses. Also the digital-type-strain character was found to be enhanced despite of slight increase in phase transition (AFE-FE) field and electrical resistivity, and decrease in maximum strain. These results were explained in terms of possible lattice defects and domain wall motion.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.247-253
• /
• 1996

Microscopic analysis has been performed in order to investigate effects of the microstructure of the starting feed rods on the morphology of the S-L interface and the stability of the molten zone during single crystal growth of $SrTiO_{3}$ using a floating zone method. Undoped and $Fe_{2}O_{3}$ doped $SrTiO_{3}$ doped $SrTiO_{3}$ specimens, sintered at the different temperatures have been used. In the case of the feed rods sintered at the lower temperature($1400^{\circ}C$), the poor densification made the stability of the molten zone difficult to maintain. The feed rods sintered at the higher temperature ($1600^{\circ}C$) exhibited the higher density but their molten zone was difficult to maintain due to the presence of the abnormally grown grains. It is concluded that the uniform grain size distribution of the feed rod is the critical factor to maintain the stable molten zone and therefore to give optimum growth condition during FZ single crystal growth.

• Journal of the Korean Magnetics Society
• /
• v.13 no.3
• /
• pp.109-114
• /
• 2003

The purpose of this study Is to investigate the effect of $V_2$O$_{5}$ addition on the microstructures and magnetic properties of 7.7${\times}$4.5${\times}$1.0 mm sized multi-layer chip inductors prepared by the screen printing method using 0∼0.5 wt％ $V_2O_{5}$-doped NiCuZn ferrite pastes. With increasing the $V_2O_{5}$ content, the exaggerated grain growth of ferrite layers was developed due to the promotion of Ag diffusion and Cu segregation into the grain boundaries oi ferrites, which affected significantly the magnetic properties of the chip inductors. After sintering at $900^{\circ}C$, the inductance at 10 MHZ of the 0.5 wt％ $V_2O_{5}$-doped chip inductor was 3.7 ${\mu}$H less than 4.2 ${\mu}$H of the 0.3 wt% $V_2O_{5}$-doped one, which was thought to be caused by the residual stress at the ferrite layers increased with the promotion of Ag diffusion and Cu segregation. The quality factor of the 0.5 wt% $V_2O_{5}$-doped chip inductor decreased with increasing the sintering temperature, which was considered to be caused by the electrical resistivity of the ferrite layer decreased with the promotion of Ag/cu segregation at the grain boundaries and the growth of the mean grain size of ferrite due to exaggerated grain growth of ferrite layers.

• Journal of the Korean Ceramic Society
• /
• v.42 no.2 s.273
• /
• pp.81-87
• /
• 2005

The compositions for LTCC embedded capacitors based on $BaTiO_3$ ceramics with $5\~15\;wt\%$ of lithium-borosilicate glass frits were studied. After the glass frits, which is chemically stable and has acceptable ability of low-temperature sintering, were added to the host dielectric materials, the sintering behavior and dielectric properties were evaluated. As for $BaTiO_3$, relative density of >$95\%$, permittivity 990, and dielectric loss $3.1\%$ were obtained when sintered at $925^{\circ}C$ with 5 wt$\%$ of glass frits. As for $(Ba,Ca)(Ti,Zr)O_3$ ceramics, relative density of >$95\%$, open porosity <$0.5\%$, permittivity 700, and dielectric loss $2\%$ were obtained when sintered at $875^{\circ}C$ with 10 wt$\%$ of glass frits.

• Resources Recycling
• /
• v.17 no.4
• /
• pp.3-9
• /
• 2008

The total amount of fluidized bed incinerator ash, i.e. incombustion materials generated from the municipal solid waste incineration(MSWI) in Korea was approximately 14,000 tons in 2006. Most of the ash after ferrous metal separation is finally discard to the landfill sites. In the present work, possibility for recycling of the ash is studied to utilize the ash as raw materials for ceramic products. Incombustion materials obtained from the two different incinerators were used to recover the raw materials by applying the magnetic separation and screening process to remove metallic particles. The raw materials show relatively low heavy metals content obtained from the KSLP leaching tests. The ceramic products were prepared by mixing the clay with the various amounts of the raw material. The physical properties, i.e. shrinkage rate, absorbancy and compressive strength of the ceramic products sintered at $1,000^{\circ}C$ and $1,050^{\circ}C$, respectively were improved by increasing the addition amounts of the incinerator ash. Based on the leaching tests the ceramic products also be satisfied with the standard limits on the leachability of heavy metals because most of the metallic materials are effectively removed from the incombustion materials by appling the separation processes.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.704-709
• /
• 2002

To improve the mechanical properties of $Al_2$O$_3$/ZrO$_2$composites, the homogeneous dispersion of ultra low size ZrO$_2$ particles in $Al_2$O$_3$ceramics have been controlled by coprecipitation method. In case of mechanical mixing of ZrO$_2$ powders with $Al_2$O$_3$, homogeneous dispersion and controlling the ZrO$_2$ size were relatively difficult due to high sintering temperature. So nanosized Zr hydroxide was coprecipitated from ZrOCl$_2$/Y(NO$_3$)$_3$ solution with commercial sub-micron sized $\alpha$-alumina (Sumitomo : AES-11(0.4 ${\mu}{\textrm}{m}$)) and high purity ultra low sized $\alpha$-alumina (Taimei Chemical (0.22 ${\mu}{\textrm}{m}$)) for low temperature sintering. By this partial coprecipitation method, relatively low sized ZrO$_2$ dispersion in $Al_2$O$_3$/ZrO$_2$ composites was achieved at 150$0^{\circ}C$-1$600^{\circ}C$ of sintering temperature range and their mechanical properties were measured.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.10a
• /
• pp.335-341
• /
• 1997

운전중 노심의 출력변화를 감시하는 노외계측기(Excore Detector)는 노내계측기(Incore Detector)를 통하여 측정되어진 축방향 출력편차(Axial Offset)를 이용하여 교정되고 있다. 노외 계측기의 전류와 축방향출력편차의 선형적인 관계를 가정하여 노내계측기로 최소한 4회 노심출력을 측정한후 최소자승법(Least Square Method)으로 비례상수들을 구하는 기존의 방법을 대신하여, 단순 노외계측기 교정법은 노내계측기로 1회 측정되어진 자료들을 이용하여 계측기 반응상수(Detector Response Factor)를 계산한 후 비례상수를 계산한다. 계측기반응상수는 2차원 중성자수송모델로부터 계산된 weighting factor와 3차원 확산이론으로부터 구한 노심출력을 이용하여 계산된다. 중성자수송계산은 (R-Z)와 (R-$ heta$)모델을 합성하여 3차원 weighting factor를 계산하므로 축방향 영향뿐만 아니라 집합체별 영향을 고려하였다. 또한 노심의 복잡한 구조로 인하여 근사적인 weighting (actor와 노심출력분포의 사용은 노외계측기의 전류와 계측기반응율의 불일치를 초래하며, 이를 해결하는 상수를 소개하여 보다 정확한 교정결과를 얻도록하였다. 이와 같은 방법을 고리 3호기 9, 10주기 전주기와 11주기초에 적용하여 노심의 연소분포, 냉각수의 온도분포, 노심의 연소도, 노심출력준위등에 대한 단순 노외계측기 교정법의 오차를 분석하여 최적의 노외계측기 교정모델을 제시하였다. 2차원 중성자수송모델 합성법에 의한 단순노외계측기 교정법은 2차원 (R-Z) 중성자수송모델보다 개선된 결과와 평균오차 0.179% 최대 오차 0.624%를 보여주고 있다.하면 조사 후의 조직안정성에도 크게 기여할 것으로 기대된다.EX>O가 각각 첨가된 경우, Ar-4vol.%H$_2$ 분위기보다 H$_2$분위기에서 소결했을 때 밀도가 더 높았다. 그러나, 결정립은 $UO_2$와 $UO_2$-Li$_2$O의 경우, 수소분위기에서 소결했을 때, (U,Ce)O$_2$와 (U,Ce)O$_2$-Li$_2$O에서는 Ar-4vol.%H$_2$분위기에서 소결했을 때 더욱 성장하였다.설명해 줄 수 있다. 넷째, 불규칙적이며 종잡기 힘들고 단편적인 것으로만 보이던 중간언어도 일정한 체계 속에서 변화한다는 사실을 알 수 있다. 다섯째, 종전의 오류 분석에서는 지나치게 모국어의 영향만 강조하고 다른 요인들에 대해서는 다분히 추상적인 언급으로 끝났지만 이 분석을 통 해서 배경어, 목표어, 특히 중간규칙의 역할이 괄목할 만한 것임을 가시적으로 관찰할 수 있 다. 이와 같은 오류분석 방법은 학습자의 모국어 및 관련 외국어의 음운규칙만 알면 어느 학습대상 외국어에라도 적용할 수 있는 보편성을 지니는 것으로 사료된다.없다. 그렇다면 겹의문사를 [-wh]의리를 지 닌 의문사의 병렬로 분석할 수 없다. 예를 들어 누구누구를 [주구-이-ν가] [누구누구-이- ν가]로부터 생성되었다고 볼 수 없다. 그러므로 [-wh] 겹의문사는 복수 의미를 지닐 수 없 다. 그러면 단수 의미는 어떻게 생성되는가\ulcorner 본 논문에서는 표면적 형태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지