• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2002.05a
• /
• pp.65-70
• /
• 2002

난연$\cdot$다기능성 복합성형체는 기계부품, 구조물, 차량, 선박, 항공기 및 산업 분야에 널리 사용되고 있다. 안전성이 확보된 신소재 개발의 일환으로서 본 연구진은 난연특성, 정전기 방지특성, 내식특성의 기능성 복합성형체 개발을 수행해 왔으며, 본 연구에서는 Recycled PE, Phenolic resin 및 PPS resin과 같은 재활용 제품에 고기능성을 부여하기 위하여 용도에 따라 alumina, silica, flyash 등의 무기질 filler를 최대 70wt(%) 이상으로 고충진한 복합 폴리머 성형체를 개발하고자 하였다.(중략)

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.97-105
• /
• 1999

In the binary system of SiC and carbon, porosity and pore size distribution of green body was controlled by varying pH, by the addition of polyelectrolyte dispersants, and by using different particle size of starting powders. The preforms having different green microstructure were fabricated by slip casting from suspensions having different dispersion condition. The reaction bonding process was carried out for these preforms. The condition of reaction bonding was 1600$^{\circ}C$ and 20 min. under vacuum atmosphere. The analyses of optical and SEM were studied to investigate the effect of green microstructure on that of reaction bonded silicon carbide and subsequently the mechanical properties of sintered body was investigated. Different green microstructures were obtained from suspensions having different dispersion condition. It was found that the pore size could be remarkably reduced for a fine SiC(0.5$\mu\textrm{m}$). The bimodal microstructure was not found in the present study, which is frequently observed in the typical reaction bonded silicon carbide. It is considered that the ratio between SiC and C was responsible for the formation of bimodal microstructure. For the preform fabricated from the well dispersed suspension, the 3-point bending strength of reaction-bonded silicon carbide was 310${\pm}$40 MPa compared to the specimen fabricated from relatively agglomerated particles having lower value 260${\pm}$MPa.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.261-265
• /
• 2014

As the need for miniaturization in water purification filter increases, the development of filter media for single filtration with multiple function was strongly required. In this study, the molded activated carbon composed of single unit was manufactured by extrusion-sintering process, and then the flow rate, density and porosity were investigated using the molded activated carbon manufactured at various extrusion temperature. We confirmed that it was possible to manufacture the single unit-molded activated carbon when the extrusion temperature was $140{\sim}230^{\circ}C$ more than $133^{\circ}C$ being of polymer binder melting point, and the optimal extrusion temperature for the molded activated carbon with maximum flow rate was $170^{\circ}C$ since the molded activated carbon had low density and high through porosity. Also we confirmed that the flow rate through the molded activated carbon was strongly dependent upon through pore porosity compared to total porosity for the molded activated carbon.

• Journal of the Korean Ceramic Society
• /
• v.37 no.11
• /
• pp.1078-1083
• /
• 2000

정전안정화 및 입체안정화를 동시에 적용한 복합안정화기구에 의하여 25 부피%의 나노 $Al_2$O$_3$슬러리를 제조하고, 이로부터 얻은 주입성형체, 원심성형체, 진공성형체의 기공구조 분석을 통하여 입자충전거동을 살펴보았다. 나노 알루미나 분말의 습식 성형체의 충전구조는 성형방법에 의하여 가해지는 외력의 영향을 크게 받지만, 반발력을 제공하는 표면장벽층의 상호작용에 의해서도 현저한 차이를 보이는 것으로 나타났다. 예비소결실험을 통하여 나노분말에서도 기공크기가 작고, 크기분포가 좁으며, 높은 밀도를 가진 균일성형체의 미세구조가 소결미세구조를 균일하게 하는데 필수적인 조건임을 확인하였다.

• Journal of the Korean Ceramic Society
• /
• v.36 no.2
• /
• pp.178-185
• /
• 1999

For the process control of silicon nitride gelcasting, the composition effect of acryamide system on the viscosity of slip and mechanical property of gelcast green body were investigated. The slip was prepared by ball milling of silicon nitride suspension prepared with acrylamide monomer and polyelectrolyte dispersant after premixing them by attritor. The slip mixed with initiator was vacuum deaired and cast into molds, and then polymerized. The consolidated green body was obtained by drying the gelated slip. The viscosity measument and the diametral compression test was done to evaluate the rheological behaviro of slip and mechanical property of gelcast body, respectively. Experimental results showed that the high solid loading of silicon nitride slip was obtained up to 46 vol% with a low viscosity. The mechanical property of gelcast body mainly increased with increasing the concentration of monomer. The gelcast body was machinable above the ∼3 MPa of tensile strength. The relative density of pressured-sintered body was 98.5% at 1760$^{\circ}C$, 3 h.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1414-1420
• /
• 1996

Using Si powder with average particle size of 8${\mu}{\textrm}{m}$ Si compacts were formed by pressureless powder packing method. The compacts were reaction bonded at 1350, 140$0^{\circ}C$ for 3~35 hrs under N2/H2 atmosphere and its microstructures were examined. Reaction bonded silicon nitrides showed nitridation of 90% and relative density of 88% After the impregnation of 5wt% MgO as sintering additive using aqueous solution of Mg nitrate the Si compacts were reaction bonded at 140$0^{\circ}C$ for 15hrs. The reaction bonded bodies were gas pressure sintered at 180$0^{\circ}C$ 190$0^{\circ}C$ 200$0^{\circ}C$ for 150, 300min. They showed relative density of 95% bending strength of 600MPa and fracture toughness of 6 MPa.m1/2.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.266-273
• /
• 1999

본 연구에서는 겔캐스팅법의 제조공정 확립을 위하여 분산제의 분자구조가 질화규소 슬립의 점성특성 및 성형체의 상대밀도와 기계적 특성에 미치는 영향을 조사하였다. 슬립과 겔캐스팅 성형체의 제조방법은 기보고된 방법과 동일하게 하였다. 그 결과, 겔캐스팅 슬립의 점성은 분산제의 분자구조와 모노머와 분산제의 구성비율에 크게 의존하였다. PMAA 분산제를 사용한 슬립의 점성은 PAA 및 PAAm 분산제 보다 높은 점도를 나타내었다. 성형체의 상대밀도는 슬립의 농도에 크게 의존하였으며, 분산제양과 모노머의 양변화에는 그다지 변화가 없었다. 그리고, 겔캐스팅 성형체의 기계적 특성은 크게 모노머의 농도에 의존하였으며, 분산제양과 슬립의 농도에는 큰 변화가 없었다.

• Transactions of Materials Processing
• /
• v.14 no.7 s.79
• /
• pp.587-594
• /
• 2005

분무성형공정은 급냉응고 및 결정입자 제어에 따른 고품위 소재 개발의 장점과 함께 고밀도 near-net-shape 제품의 제조가 가능한 합금제조기술이다 분무성형체의 미세조직은 적층표면에 도달하는 액적들의 평균 열용량, 즉 고상분율에 의하여 결정되며, 이는 액적의 비행과정에서의 분사가스-액적간의 열전달과 적층표면에서의 열유입과 열유출 속도에 영향을 받는다. 실제 다양한 공정변수들이 복합적으로 미세조직 형성과정에 영향을 미치지만, 균일한 미세조직을 얻기 위하여서는 적층표면에서의 온도와 고상분율을 항상 일정하게 제어하여야만 한다 즉, 적층표면 온도를 분무 성형공정중에 지속적으로 측정하여 이를 공정 제어 시스템에 feedback하여 원하는 적층표면온도를 유지하도록 공정변수를 제어하는 것이 필수적이다. 분무성형에 제조된 성형체는 합금원소의 편석이 없고 미세한 등방성의 결정립으로 이루어진 특징적인 미세조직을 나타낸다 이와 같은 미세조직으로 인하여 분무성형체는 우수한 성형성과 기계가공성을 나타내며, 또한 분무성형-후속가공된 최종 제품은 잉곳주조에 의하여 제조된 것과 비교하여 크게 향상된 기계적 성질을 가진다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.796-799
• /
• 2004

The effects of forming presure, organic binder content and moisture on flexural strength were investigated. As moisture content increased in the granules during compaction, the density and strength of the green body were increased. Green strengths were found to improve more strongly with increasing forming pressure in the case of using the granules of higher organic content. The sintered strength was the highest with the organic content of 0.2wt％ under all forming pressures.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2003.10a
• /
• pp.351-354
• /
• 2003

최근 안전 분야에서 기능성 고분자 재료의 응용분야로서 첨단 전기전도성 고분자복합재료를 이용한 섬유상, 구형, flake 등 각종 형상의 금속, 흑연, carbon black, whisker 등의 전도성 filler를 고분자 matrix에 혼입하여 전도성 고분자를 성형가공하여 복합성형체를 제조하고 electrical hazard를 감소시키기 위한 정전기방지효과, 자기발열체, 전자기파 차폐효과 등의 특성을 나타내는 고분자 성형체상으로 가공된 소재로 화학공장, 산업설비, 각종 제조설비의 제조 공정용 제어, 과전류차단 및 외부 전자기파에 의해 발생되는 이상작동 등을 방지하는 안전시스템 소재용으로서 다양하게 사용되고 있다.(중략)