• The Journal of Engineering Geology
• /
• v.31 no.1
• /
• pp.67-81
• /
• 2021

Grouting is used for reinforcement and waterproofing of soft ground to increase its bearing capacity, reduce the impacts of rising or lowering groundwater levels, and reduce subsidence due to vibration and general causes. This study investigated the enhancement of grout strength and hardening time by the addition of reinforcing fibers, and the development of non-cement grouting materials from blast furnace slag. An experiment was performed to measure the increase in grout strength resulting from the addition of 0.5% increments of aramid and carbon reinforcing fibers. The results show that the uniaxial compressive strength of grout increases with increasing content of reinforcing fiber. Comparison of three admixtures of finely powdered blast furnace slag and 10%, 20%, and 30% calcium hydroxide stimulating agent showed that the uniaxial compressive strength of the mixture increases with increasing content of alkaline stimulant; however, the strength was lower than for 100% pure cement. The reaction of calcium hydroxide with blast furnace slag powder, which increases the strength of the grout, is more effective if injected as a solution rather than a powder.

• Korean Journal of Food Science and Technology
• /
• v.40 no.6
• /
• pp.680-685
• /
• 2008

In this study, we assessed the functional characteristics of Aralia continentalis Kitagawa (AcK) and Aralia continentalis Kitagawa leaf (AcK-leaf), including crude saponin contents, antioxidant activity, nutritive elements, dietary fiber, and chlorophyll contents. The results of our analysis of nutritive elements in AcK, the contents of the general components, inorganic components, and vitamins were all relatively high. The contents of inorganic components were also high in the following order: K>Ca>P>Na>Mg. Among vitamins, $\beta$-carotene and vitamin C contents were all high. The crude saponin content was 63.7 mg/g in the AcK and 63.5 mg/g in the AcK leaf, and the antioxidant activity was determined to be relatively high. With regard to the dietary fiber content, the total dietary fiber content was 2.13% (soluble 0.40, insoluble 1.72) in the AcK and 5.98% (soluble 1.06, insoluble 4.89) in the AcK leaf, and the total chlorophyll content was 92.58 mg in the AcK and 147.25 mg/100 g in the AcK-leaf.

• Magazine of the Korea Concrete Institute
• /
• v.8 no.5
• /
• pp.163-170
• /
• 1996

Cellulose fibers, being fairly strong and stiff as well as cheap and plentiful with low energy demand during manufacture, are strong contenders for the reinforcement of cement-based materials. Cellulose fiber-cement composites, generally manufactured by slurry-dewatering procedure, can find applications in the production of flat and corrugated cement sheets and many other thin-sheet cement products. This paper presents the results of an experimental study concerned with the effects of fiber content and moisture conditions on the flexural performance of these composites. An effort was also made to study the effect of pozzolanic admixtures on the flexural performance in different moisture conditions. The test results obtained were analyzed statistically using the analysis of variance in order to derive reliable conclusions. The results generated in this study were indicative of significant effects of fiber content and moisture condition of flexural performance. There is a tendency in flexural strength to increase in increase in fiber content up to 8%: flexural toughness values continue to increase even at higher fiber contents. Moisture content has a significant effect on the flexural performance. There is a tendency in flexural strength to decrease and flexural toughness to increase with increasing moisture content Composites incorporating pozzolans showed an increase in the flexural strength while slightly reducing the flexural toughness and were sensitive to variations in moisture content.

• Composites Research
• /
• v.28 no.5
• /
• pp.249-253
• /
• 2015

This paper reports a study on a method for achieving lightweight thermoplastic laminate composites referred to as tow spreading technology. Thickness of an unspread 12 K carbon fiber tow is reduced by increasing the tow width from 7 mm to 20 mm. The polypropylene (PP) film was used to stabilize and impregnate the spread tow, covering it into a partially consolidated prepreg: 12 K carbon fiber spread tow/PP. Laminates were fabricated from the spread tow prepreg and control laminate composites were produced from unspread tow prepreg consisting of 12 K carbon fiber and PP. The void content, tensile and flexural properties of the composite laminates were investigated. Consequently, the spread tow laminate composite exhibited lower void content and improved mechanical properties.

• Composites Research
• /
• v.23 no.3
• /
• pp.31-36
• /
• 2010

A new material, carbon-nanofiber/polypyrrole (CNF/PPy) composite films, with different CNF weight ratios were fabricated electrochemically. Compared to the fabrication process based on simple physical mixing, the flexibility of the new film has been improved much better than the previous similar material. Pure PPy films were also fabricated by the new electrochemical process for the comparison of difference. Several SEM images were taken at two locations (electrode-side and solution-side) and at the cross section of the samples. Electrical conductivity of the composite films was measured by the four-probe method. The conductivity of the pure PPy film 0.013cm thick was 79.33S/cm. The CNF/PPy composite film with 5% CNF showed a conductivity of 93S/cm. One with 10% CNF showed a conductivity of 126 S/cm. The conductivity of PPy improves, as the CNF weight ratio increases. The good conductivity of CNF/PPy composites makes them a candidate for a small bending actuator. A bending sensor consists of PPy and PVDF, which can be operated in the air, was designed and the bending deflection was calculated using FEM.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.395-398
• /
• 2006

동일한 조건에서 순수한 물과 계면활성제인 DBS(dodecyl bezebe sulfonic acid) 25ppm을 첨가한 물에 대해 천연가스 하이드레이트를 제조시 가스의 함유량은 각각 80배와 160배로 2배의 차이가 발생한다. 이에 대해 본 연구에서는 결정 생성 형태의 관찰 및 $^{13}C$ NMR을 사용한 분광학적 구조 분석으로부터 이의 원인을 찾고자 하였다. 순수한 물과 DBS를 미량 함유한 물을 사용하여 whiskery 결정을 생성시킨 결과, 순수한 물을 사용한 경우보다 섬유 다발 형태가 매우 활발한 형태의 결정 형태로 가스하이드 레이트가 생성됨을 알 수 있었다. 또한 400MHz의 NMR을 사용한 분광학적 구조 분석으로부터 천연가스하이드레이트는 구조-I과 구조-II가 혼재된 결정 구조를 이루고 있음을 알 수 있었다. 또한 DBS를 함유한 물에 의해 제조된 천연가스하이드레이트는 arge cage를 많이 생성시키는 역할을 하는 분석 결과를 보였고 이것이 가스 함유량을 증대시키는 원인 중의 하나임을 알 수 있었다.

• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.288-294
• /
• 1994

Dietary fiber contents in brans of the two representative Korean rice varieties, Chucheong and Sucheon were measured by the AOAC method, and the composition of total dietary fiber (TDF) was analyzed with the acid detergent fiber (ADF) procedure. Rice bran contained more than 25% of TDF, most of which was insoluble dietary fiber. Hemicellulose was shown to be the major constituent and rice bran dietary fiber contained distinctive amounts of cellulose and uronic acid. Consecutive acidalkaline treatment of rice bran considerably increased soluble dietary fiber (SDF) content and water-holding capacity (WHC). WHC of wheat flour-rice bran dietary fiber mixture increased with the proportion of rice bran dietary fiber. Analysis of the differential scanning calorimetry thermograms revealed that rice bran dietary fiber effectively retarded retrogradation of wheat starch.

• Composites Research
• /
• v.12 no.6
• /
• pp.8-14
• /
• 1999

This research is focused on the investigation of impact strength and the microscopic observation of material behavior of glass fiber reinforced polypropylene in solid phase forming. The fiber weight per-centage of the composite materials was 20%, 30% and 40%. The solid-phase formed specimens were pre-strained to 10%,20%. and 30% strain levels. The forming temperatures of specimens were $100^{\circ}C$, $125^{\circ}C$ and $150^{\circ}C$. Izod impact test was performed with unnotched specimens. With increasing the glass fiber content ; the impact strength was increased.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.307-312
• /
• 2009

The fabrication of PHBV nanofibers containing various plant polyphenols by electrospinning has been examined. It has been found that the average diameters of fibers increased by the adding of polyphenols. The resulting fibers exhibited a uniform diameter ranging from 340 to 450 nm. As the concentration of polyphenols increased, the diameter of fibers increased due to the hydrogen bonding interaction between the ester groups of PHBV and hydroxyl groups of polyphenols. The interaction between PHBV and polyphenols, which forms a complex together in solution, was verifed by UV measurement. ATR-FTIR analysis confirmed the existence of the hydrogen bonding interaction. The semicrystalline structure of the PHBV nanofiber was observed from XRD pattern. The crystallinity of PHBV nanofibers was increased by the adding of polyphenols. PHBV nanofibers containing polyphenols showed superior antimicrobial activities.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.2
• /
• pp.83-90
• /
• 2006

A spalling is defined as the damages of concrete exposed to high temperature during the fire by causing cracks and localized bursting of small pieces of concrete. It is reported that spalling is caused by the vapor pressure and polypropylene(PP) fiber has an important role in protecting from spalling. The characteristics of fire resistance of high-strength reinforced concrete columns with various concrete strength and various contents of PP fiber were investigated in this study. In results, the ratio of unstressed residual strength of columns increases as the concrete strength increases and the ratio of unstressed residual strength of columns exposed to fire decreases as the content of PP fiber increases from 0% to 0.2%.