• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.860-868
• /
• 2000

In this work, the electro-magnetic interference (EMI) characteristics of PAN-based carbon fibers-reinforced composites are investigated with difference to manufactural parameters, i.e., fiber grade, fiber orientation angle, and laminating method. As a result, EMI shielding effectiveness (SE) of the composites greatly depends on a fiber orientation in composite angle. Especially, the fiber grade affects SE of composites in case of orientation angle of 0$^{\circ}$. Then the SE become greater as the change of electric character according to the arrangement directions, i.e., electrical anisotropy in the same constituent materials. This is due to the skin effect which is represented in the surface of electro-magnetic wave in high-frequency range. In all cases according to lamination methods, the composites represents SE of 83~98% over. Whereas, in symmetric and unsymmetric laminate structures, the SE decreases slightly as the laminate angles of composites increases. On the contrary. the repeating laminates structure shows the opposite tendency. Especially, 90$^{\circ}$ repeating laminate structure shows the SE more than 90% over the measuring frequency.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1439-1441
• /
• 2003

전기절연재의 구조재로 많이 사용되고 있는 FRP(fiber reinforced plastics)는 열경화성 수지를 접착성 결합제(binder)로 하고 고강도 섬유를 보강재로 한 복합재료로서 기계적, 화학적, 전기적 특성이 매우 우수하다. FRP의 기계적 강도는 유리섬유에 의존 하고 있으므로 유리섬유의 방향과 힘을 가하는 방향에 따라서 그 강도의 차이는 매우 크게 나타난다. 본 연구에서는 섬유의 배향에 따른 강도의 변화를 이해하기 위하여 시편을 제작하여 압축강도를 측정하고 압축강도와 응력의 분포를 유한요소법으로 시뮬레이션하였다. FRP rod에 압축응력이 가해졌을 때 섬유의 배향에 따른 파괴강도와 응력의 분포를 유한요소법을 이용하여 시뮬레이션하였고 모델링에는 3-D Shell과 3-D Brick 요소를 사용하였다. 제작된 시편의 강도특성과 시뮬레이션을 통한 응력의 분포를 서로 비교하여 시편의 파괴에 미치는 응력을 고찰하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.4
• /
• pp.599-606
• /
• 1999

복합 적층 판과 보강 재를 설치한 보강된 복합 적층 패널의 좌굴을 고려한 설계에서, 좌굴이 항상 구조물의 최종 파손을 의미하는 것은 아니므로 이들의 좌굴 및 좌굴 후 거동에 대한 정확한 이해와 연구가 필요하다. 본 연구에서는 유한요소 법을 이용하여 적층 메커니즘과 섬유 배향각, 적층 순서 등이 복합 적층 판과 보강된 복합 적층 패널의 좌굴 및 좌굴 후 거동에 미치는 영향을 체계적으로 해석하였고, 각 변수에 따른 좌굴 및 좌굴 후 거동 특성을 분석하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.4
• /
• pp.953-959
• /
• 1998

To investigate accuracy of intensity method for measurement of the fiber orientation distribution, fiber orientation function is calculated by drawing simulation figures for the fiber orientation as varying fiber aspect ratio, fiber area ratio, and fiber orientation state, respectively. The values of fiber orientation function measured by intensity method are compared with the calculated values of fiber orientation function. The results show that measurement accuracy of the fiber orientation angle distribution by intensity method is affected by the fiber aspect ratio when the total length of oriented fiber is same. The average gradient of fiber orientation function is 0.94 for 1000mm of the total fiber length and is 0.93 for 2000 mm when the fiber aspect ratio is over 50. Measurement accuracy by intensity method is about 94% and the reliable data can be obtained by intensity method.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.3
• /
• pp.34-43
• /
• 1996

In this study basic equations of fiber orientations is cimpared with experimental results. It is found that fiber orientations of short fiber reinforced polymeric composite under compression molding are governed by slope of flow speed in x-y direction. Fiber orientation angle of mold is also found to increase with closure speed and the compression ratio. At the middle of the mold, the slope of flow speed is larger in x-direction than in y-direction. At the wall of the mold, the shope of flow speed in y-direction occurs due to the effect of friction, hence affects the fiber orientation. The effect of partial flow, which incurs y-direction orientation causes to increase the fiber orientation angle at the fore part of the flow.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.479-482
• /
• 2004

The behavior of fatigue delamination in a GLARE(Glass Fiber Reinforced Metal Laminates) under fatigue loading conditions investigated. The behavior of fatigue delamination was examined basing on investigation of the crack and delamination using a SAM (Scanning Acoustic Microscope). The crack and delamination behavior on the relationship among a-N, SAM images and crack length-delamination length were considered. The test results indicated the features of different fatigue delamination and crack growth according to each fiber orientation angle and also obtained to more increase delamination than crack through the relationship between crack length and delamination length in GLARE.

• Composites Research
• /
• v.22 no.4
• /
• pp.1-12
• /
• 2009

In this paper, quasi-static crushing tests of composite circular tubes under axial compression load are conducted to investigate the energy absorption characteristics. Circular tubes used for this experiment are glass/epoxy (GFRP) composite tubes which are fabricated by the filament winding method. One edge of the composite tube is chamfered to reduce the initial peak load and to prevent catastrophic failure during crushing process. Energy absorption characteristics vary significantly according to the constituent materials, fabrication conditions, tube geometry and test condition. In tube geometry, according as inner diameter increase, unstable crush mode is caused by local buckling of delamination, but control of the fiber orientation should help composite tubes get stable crush mode.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.422-425
• /
• 2003

Investigated whether fiber orientation distribution of twisted yarn composites and the fiber content are 0$^{\circ}$ and 90$^{\circ}$ direction tensile strength and some correlation. Tensile strength of 0$^{\circ}$ directions of twisted yarn composites increased changelessly being proportional the fiber content and fiber orientation function get into anisotropic in isotropic. But, tensile strength ratio by separation of fiber filament of 90$^{\circ}$ directions tensile strength decreased when tensile load is imposed for width direction of reinforcement fiber. 0$^{\circ}$ and 90$^{\circ}$ direction tensile strength ratio value of a twisted yarn composites not receive almost effect of the fiber content of fiber orientation function J = 0.4 lows. Although do, 20 wt% of the fiber content is high about 0$^{\circ}$ and 90$^{\circ}$ direction tensile strength ratio about 1.6~2 than 10 wt% from J = 0.4. Therefore. could know that effect of the fiber content is dominate.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.219-224
• /
• 2015

In this work, the effect of fiber array direction including $0^{\circ}$, $0^{\circ}/90^{\circ}$, $0^{\circ}/45^{\circ}/-45^{\circ}$ was investigated for mechanical properties of basalt fiber-reinforced composites. Mechanical properties of the composites were studied using interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$) measurements. The cross-section morphologies of basalt fiber-reinforced epoxy composites were observed by scanning electron microscope (SEM). Also, the surface properties of basalt fibers were determined by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). From the results, it was observed that acid treated basalt fiber-reinforced composites showed significantly higher mechanical interfacial properties than those of untreated basalt fiber-reinforced composites. These results indicated that the hydroxyl functional groups of basalt fibers lead to the improvement of the mechanical interfacial properties of basalt fibers/epoxy composites in the all array direction.

• The Korean Journal of Rheology
• /
• v.7 no.2
• /
• pp.158-167
• /
• 1995

농도 5w%의 초고분자량 폴리에틸렌(분자량:1.5$\times$106)을 상온으로 냉각시켜 벨을 만 들고 이를 방사하여 섬유를 제조하였다. 이때 방사구를 나온 섬유를 $0^{\circ}C$에서 9$0^{\circ}C$까지의 냉 각조를 통과시켜 젤화/결정화 온도를 다르게 하였다. 최대 연신비는 온도가 $0^{\circ}C$에서 7$0^{\circ}C$까 지 증가함에 따라서 증가하고 9$0^{\circ}C$에서 젤화/결정화시킨 섬유의 경우에는 감소한다. 시차주 사열분석, 배향, 인자, 복굴절률, 절단강도와 탄성률을 측정하여 섬유의 물성에 대해 고찰하 였다. 연신비의 증가에 따른 결정화도, 용융 온도, 복굴절률의 증가는 높은 온도에서 젤화/ 결정화시킨 섬유인 경우가 더 뚜렷했다.