• Journal of Korean Society of Forest Science
• /
• v.24 no.1
• /
• pp.45-52
• /
• 1974

This study was carried out to examine the subsitution possibility into water soluble amino resins instead of phenolic resin as a sizing material for the strength increase on the wet forming hardboard. The properties of hardboard, manufactured with amino-resins based urea, melamine, formaline, and methanol which were low priced domestic products, were examined in comparison with those of hardboard treated with phenolic resin. In this study by the results and discussions, it may be summarized as follows: 1. Amino-resins are able to be substituted for the phenolic resin as a good sizing material for strength increase in the manufacture of wet forming hardboard. Under the considerations of economic advantages and properties of hardboard, modified urea-melamine resin was given a best results. 2. The specific gravities of hardboard that were treated with phenolic resin was equal to that treated with modified amino type resin, and in case of urea-melamine resin, the specific gravity value were lowest among them. 3. The results of moisture contents were satisfied the standard which calls for 13 percent or below. There were no differences in moisture contents between hardboards, treated with melamine resin and modified urea-melamine resin but phenolic resin. The moisture contents of hardboard treated with phenolic resin was shown the lowest. 4. The water absorption of hardboard treated with phenolic resin was greater than those treated with amino resins, and to satisfy the standard of water resistance, the treatment of 2 percent paraffin wax emulsion was needed in this case. There were no differences in water absorptions between hardboards, treated with melamine resin and modified urea-melamine resin. To satisfy the standard of water resistance in this case the treatment of 1 percent paraffin wax emulsion was shown good results. 5. The differences among the flexural strength in using tested three adhesives were significant. The flexural strength were shown the signification by order of melamine resin, modified urea-melamine resin, and phenolic resin. In all cases to satisfy the standard of flexural strength, the treatment of 3 percent sizing materials for strength increase was needed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.2
• /
• pp.93-102
• /
• 2007

A large number of FRP decks are already in service worldwide because the lighter FRP-based bridge decks are ideal for rapid construction to reduce the dead load of superstructures. And the proper design process is demanded for the effective FRP deck application. In this paper, to get the basic prototype of FRP bridge decks, the ratio of individual parameters, which compose the specification of FRP bridge decks, are determined by a finite element analysis. In addition, optimum FRP deck shapes are determined considering complex constraints and material properties of bi-directional characteristics. Upon these results, the prototype of FRP bridge decks is validated.

• Composites Research
• /
• v.16 no.5
• /
• pp.39-44
• /
• 2003

Embedding viscoelastic-damping materials into composites can greatly increase the damping properties of composite structures. Usually viscoelastic-damping materials behave isotropically so that their damping properties are the same in all directions. In these days, there is a desire to develop viscoelastic-damping materials that behave orthotropically so that damping properties vary with material orientation. These orthotropic damping materials can be made by embedding rows of thin wires within the viscoelastic materials. These wires add significant directional stiffness to the damping materials. where the stiffness variation with wire orientation follows classical lamination theory. In this paper, the loss factor of composite laminate was evaluated based on Ni and Adams' theory. To investigate the effect of directional damping material, the low-velociy impact response analysis was also performed. The present analysis results show that directional damping material has a great influence on vibration and damping characteristic of composite laminate.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.65-68
• /
• 2001

In this research, damage initiation in singly oriented ply (SOP) FML under concentrated loading conditions was studied. The finite element method (FEM) base on the first order shear deformation theory is used for the analysis of fiber orientation effect on FML under concentrated loading conditions. The failure indices were calculated for the variation of fiber orientation and the results were compared with indentation experiments. The failure indices were well matched with damage initiation of SOP FML. Indentation results shows that the crack initiation of SOP FML is determined by stiffness induced by fiber orientation and tile penetration load of SOP FML are influenced by the deformation tendency and boundary conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.2
• /
• pp.393-398
• /
• 1990

A method is proposed which can be used to obtain the fibesr content distribution of compression molded long fiber-reinforced thermoplastic sheet for nonisothermal state. The fiber is modelled to be a sphere. Once the one-dimensional unsteady state heat conduction equation in solved, the mean temperature in defined across the thickness direction. The viscosity of matrix is determined with the mean temperature. Using the obtained viscosity, two-dimensional sheet0like part compression molding is simulated with the finite element method. Comparison with experiments shows that the method accurately predicts the distribution.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.370-375
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Tensile and indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.213-214
• /
• 2019

Oriented strand board(O.S.B) is used in many areas, such as interior and interior finishes of wooden houses, but no cases and studies have been used as flooring materials for flooring boards. In this study, we will examine the quality and performance of the aromatic strands board, which we believe can be substituted for the plywood, and analyze its suitability as a floorboard.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.104-113
• /
• 1993

Characteristics of fiber-reinforced thermoplastic sheet depend on the quantity and shape of fibers. During a molding process of composites, the fiber-maxtrix separation and fober orientation are caused by the flow during the molding process. As a result, the product tends to be nonhomogeneous and anisotropic. Hence, it is very important to clarify the relations between separation-orientation and molding conditions. The correlation between the separation and the orientation have to be clarified for designing the fiber structure. In this paper, the degree of nonhomogeneity which is a measure of the separation is obtained using one-dimensional rectangular shaped part compression molding. And the orientation function is defined and measured by the image processing using soft X-rayed photograph and image scammer. Correlation between the degree of nonhomogeneity and the orientation function is discussed.

• Journal of Biomedical Engineering Research
• /
• v.24 no.1
• /
• pp.23-29
• /
• 2003

The prevalence of discogenic pain among patients with chronic low back pain is estimated to be about 40%. Lumbar discectomy is being performed as a treatment according to the studies done so far. Recently IDET- Intradiscal electrothermal therapy which is minimally invasive technique is being introduced. This study will investigate important factors of this procedure such as the temperature of heat source, loading times, and the temperature distribution within the intervertebral disc. This study utilized finite element analysis and experiment. It was able to analyze the temperature range of inner intervertebral disc by two mechanisms which are known to alleviate pain clinically. As a result, verification of temperature distribution to 15.6mm($\geq$45$^{\circ}C$) (Mechanism 1-coagulation inner annulus by heat) and 9mm($\geq$6$0^{\circ}C$) (Mechanism 2- contraction inner nucleus by heat) from the heat source was done.

• Applied Chemistry for Engineering
• /
• v.29 no.2
• /
• pp.229-236
• /
• 2018

A customized cleaning agent was investigated for improving the performance decreased by the pollution of collecting plates in an electric fume collector (EFC) which was developed and applied for the purification of effluent gas including oil mist from the textile industry. The pollutants on the surface of collecting plates were blackened by the condensation of oil mist for a long time and difficult to remove by general cleaning agents. The composition of an optimized cleaning agent consisted of alkali, alcohol, glycol and non-ionic surfactant sources was determined by considering the pollutant properties and effect on the damage of the basic metal of collecting plate and so on. The developed cleaning agent solution diluted by 9.1% was applied to the field test, and also the pollutants strongly adhered on collecting plate surfaces were successfully removed by a simple spraying method. The effluent gas purification efficiency of EFC increased significantly by cleaning of collecting plates.