• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.160-167
• /
• 2007

This paper proposes a model for the solutions predicting the coefficient of thermal expansion of composites including fiber-like shaped$(a_1>a_2=a_3)$ and disk-like shaped$(a_1=a_2>a_3)$ inclusions like two dimensional geometries, which was analyzed by one axis and a single aspect ratio, $(\rho_\alpha=a_1/a_3)$. The analysis follows the procedure developed for elastic moduli by using the Lee and Paul's approach. The effects of the aspect ratio on the coefficient of thermal expansion of composites containing aligned isotropic inclusions are examined. This model should be limited to analyze the composites with unidirectionally aligned inclusions and with complete binding to each other of both matrix and inclusions having homogeneous properties. The longitudinal coefficients of thermal expansion $\alpha_{11}$ decrease and approach the coefficient of thermal expansion of filler, as the aspect ratios increase. However, the transverse coefficients of thermal expansion $\alpha_{33}$ increase or decrease with the aspect ratios.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.521-528
• /
• 2012

In this study, we analyzed the physical properties of an ethylene oxide adducted amphoteric surfactant such as critical micelle concentration, surface tension, interfacial tension, contact angle, viscosity and phase behavior. The dual function characteristics of an amphoteric surfactant were investigated by determining an isoelectric point, which were attained using zeta potential measurements and quartz crystal microbalance (QCM) experiments. The isoelectric points of DE3-OSA82-AO, DE5-OSA82-AO and DE9-OSA82-AO surfactant systems determined by zeta potential measurements were 6.97, 6.93 and 7.10 respectively and they are in good agreement with the isoelectric point values measured by QCM experiments. The frictional property measured using an automated mildness tester showed that the DE-OSA82-AO surfactant could provide a good softening effect at neutral condition.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.4
• /
• pp.262-270
• /
• 2021

Consumption of Liquefied Natural Gas (LNG) has increased due to environmental pollution; therefore, the need for LNG carriers can efficiently transport large quantities of LNG, is increased. In various types of LNG Cargo Containment System (CCS), Membrane-type MARK-III composed of composite materials is generally employed in the construction of an LNG carrier. Among composite materials in a Mark-III system, glass-fiber composites act as a secondary barrier to prevent the inner hull structure from leakage of LNG when the primary barrier is damaged. Nevertheless, several cases of damage to the secondary barriers have been reported and if damage occurs, LNG can flow into the inner hull structure, causing a brittle fracture. To prevent those problems, this study conducted the applicability assessment of composite material manufactured by bonding glass-fiber and aluminum with epoxy resin and increasing layer from three-ply (triplex) to five-ply (pentaplex). Tensile tests were performed in five temperature points (25, -20, -70, -120, and -170℃) considering temperature gradient in CCS. Scanning Electron Microscopy (SEM) and Coefficient of Thermal Expansion (CTE) analyses were carried out to evaluate the microstructure and thermos-mechanical properties of the pentaplex. The results showed epoxy resin and increasing layer number contributed to improving the mechanical properties over the whole temperature range.

• Composites Research
• /
• v.21 no.5
• /
• pp.9-14
• /
• 2008

Carbon nanofibers (CNFs) were used as dielectric lossy materials and NiFe particles were used as magnetic lossy materials. Total twelve specimens for the three types such as dielectric, magnetic and mixed radar absorbing materials (RAMs) were fabricated. Their complex permittivities and permeabilities in the range of $2{\sim}18$ GHz were measured using the transmission line technique. The parametric studios for reflection loss characteristics of each specimen to design the single-layered RAMs were performed. The mixed RAMs generally showed the improved absorbing characteristics with thinner matching thickness. One of the mixed RAMs, MD3with the thickness of 2.00 mm had the 10 dB absorbing bandwidth of 4.0 GHz in the X-band ($8.2{\sim}12.4$ GHz). It also showed very broad 10 dB absorbing bandwidth as wide as 6.0 GHz in the Ku-band ($12.0{\sim}18.0$ GHz) with the thickness tuning to 1.49 mm. The experimental results for selected several specimens were in very good agreements with simulation ones in terms of the overall reflection loss characteristics and 10 dB absorbing bandwidth.

• Composites Research
• /
• v.19 no.1
• /
• pp.29-35
• /
• 2006

The avoidance of enemy's radar detection is very important issue in the modem electronic weapon system. Researchers have studied to minimize reflected signals of radar. In this research, two types of radar absorbing structure (RAS), 'C'-type shell and 'U'-type shell, were fabricated using fiber-reinforced composite materials and their radar cross section (RCS) were evaluated. The absorption layer was composed of glass fiber reinforced epoxy and nano size carbon-black, and the reflection layer was fabricated with carbon fiber reinforced epoxy. During their manufacturing process, undesired thermal deformation (so called spring-back) was observed. In order to reduce spring-back, the bending angle of mold was controlled by a series of experiments. The spring-back of parts fabricated by using compensated mold was predicted by finite element analysis (ANSYS). The RCS of RAS shells were measured by compact range and predicted by physical optics method. The measured RCS data was well matched with the predicted data.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.7 no.11
• /
• pp.925-932
• /
• 2017

In this study, the analysis of plate under torsion was carried out according to stacking angle at the unidirectional carbon fiber reinforced plastic(UD CFRP) among composite materials. In case of UD CFRP, the material property due to stacking angle becomes different. Also, the stacking angles were designated to 15°, 30°, 45°, 60°, 75° and 90° at the study models. The notch hole was applied at the center part by supposing that rivet or hole was used. The analysis method was used by applying the experimental method at ISO 15310. Two jigs were fixed at the lower part and two jigs were descending at the upper part. As seen by the analysis result values at this study, the shear stress happening at the fracture part was seen with the lowest value in case of the stacking angle of 45°. It is known that the case of the stacking angle of 45°has the structural safety and durability higher than those of the other stacking angles when the torsion applies. It is thought that this result can be applied to the data of basis which can be devoted to the durability when the torsion is applied at CFRP plate.

• Elastomers and Composites
• /
• v.37 no.4
• /
• pp.224-233
• /
• 2002

This study has investigated the flame retardant properties of EPDM rubber with the addition of various flame retardants. Carbon black, stearic acid, zinc oxide cross-linking agent were mixed with EPDM rubber to produce the base rubber E0 without the addition of flame retardants. Phosphorus flame retardant Tricrecyl phosphate(TCP) was added to E0 in 0.5, 1, 1.5, 2 phr to make E1~E4 samples and red phosphorus was added in 3, 6, 9, 12 phr to make E5~E8 samples. A flame retardant of the bromine family Decabromodiphenyloxide(DBDPO), and a chlorinated paraffin retardant of the chlorine family was added to E0 in 3, 6, 9, 12 phr to make E9~E12 and E13~E16 samples, repectively. Basic physical properties such as tensile strength, tear strength and hardness were measured for all the rubber samples with various flame retardant additions. There was no substantial differences. On the other hand, Oxygen index and UL94 were measured to study flame retardant properties. From oxygen index measurements E0 sample showed a value of 23.5%, indicating the improvement of flame retardant properties. Also from UL94 measurements, it was found that addition of red phosphorus resulted in maximum flame retardant effect. It was found that increasing the amount of addition resulted in decreasing combustion rate and improving flame retardant effect regardless of the kind of flame retardant.

• Food Science and Preservation
• /
• v.30 no.5
• /
• pp.896-904
• /
• 2023

The texturization characteristics of textured vegetable protein (TVP) were investigated based on the extent of soybean decoating during the pretreatment of defatted soybean flour used for TVP. The raw materials for TVP consisted of 50% defatted soybean flour, 30% gluten, and 20% corn starch. The weight ratios of soybean seed coat to soybean flour were 9%, 6%, 3%, and zero. Extrusion was performed using an extruder equipped with a cooling die, maintaining a barrel temperature of 190℃ and screw speed of 250 rpm, Water was injected at a rate of 9 rpm using a metering pump. Regarding the textures of the extruded TVPs produced from defatted soybean flour, an increase in the soybean seed coat content led to a decrease in the apparent fibrous structural layer and an increase in hardness. However, there were no significant changes in elasticity and cohesion. Moreover, as the soybean seed coat content increased, the pH of TVPs decreased. A higher soybean seed coat content also tended to lower the moisture content, increasing water absorption, solids elution, and turbidity. These results suggest that an increased seed coat content reduces the proportion of protein, and the fibers present in the seed coats prevent texturization.

• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.577-584
• /
• 2018

This study was conducted to investigate the potential of chicken feather (CF), which is a by-product in poultry industry, as a partial substitute of wood fiber in the production of wood-based fiberboard. Keratin-type protein constituted the majority of CF, and its appearance did not differ from that of wood fiber. When the formaldehyde (HCHO) adsorptivities of CF compared by its pretreatment type, feather meal (FM), which was pretreated CF with high temperature and pressure and then grounded, showed the highest HCHO adsorptivity. In addition, there was no difference between the adsorbed HCHO amounts, which was measured by dinitrophenylhydrazine method, of scissors-chopped CF and CF beated with an electrical blender. Mechanical properties and HCHO emission of medium-density fiberboards (MDF), which were fabricated with wood fiber and 5 wt% CF, beated CF or FM based on the oven-dried weight of wood fiber, were not influenced by the pretreatment type of CF. However, when the values compared with those of MDF made with just wood fiber, thickness swelling and HCHO emission of the MDF were improved greatly with the addition of CF, beated CF or FM. Based on the results, it might be possible to produce MDF with improved dimensional stability and low HCHO emission if CF, beated CF or FM is added partially as a substitute of wood fiber in the manufacturing process of MDF produced with the conventional urea-formaldehyde resin of $E_1$ grade. However, the use of CF or FM in the production of MDF has a low economic feasibility at the current situation due to the securing difficulty and high cost of CF. In order to enhance the economic feasibility, it requires to use CF produced at small to medium-sized chicken meat plants. More importantly, it is considered that the technology developed from this research has a great potential to make provision for the prohibition of animal-based feed and to dispose environmentally avian influenza-infected poultry.

• The korean journal of orthodontics
• /
• v.33 no.2 s.97
• /
• pp.103-111
• /
• 2003

The Purpose of this study was to evaluate the effect of occlusion on the mechanical strength of periodontal fibers during retention periods after experimental tooth movement. In the Sprague-Dawley male rats weighing 200g or more, the ntraoral elastics were inserted into the both right and left interproximal space between upper first and second molars for tooth movement. kiter 4 days later, the left lower first, second, and third molars were extracted for differentiating the non-occlusal side from the occlusal side in the same mouth. At the same time the elastics were removed and then light cured resin was Placed in the space between upper first and second molars following undercut was made for retention bilaterally. From the beginning of retention, 7 rats were sacrificed at 0, 4, 8, 12, 16, 20 days respectively. For evaluating of magnitude on the mechanical strength of periodontal tissue, the maximal shear load of the upper first molars were measured bilateraly during extraction using Instron Universal Testing Machine. The results of this study were obtained as follows : 1. In the occlusal side, the maximal shear load was increased from no retention to retention 20 days group as time was going and statistically difference was shown from retention 12 days group (p<0.05). 2. In the non-occlusal side, the maximal shear load was increased slightly from no retention to 20 days group as time was going but there was no statistically difference (p>0.05). 3. The result compared with the maximal shear load between occlusal and nonocclusal side showed no statistically difference until retention 8 day group (p>0.05), but showed statistically difference from retention 12 day to 20day group (P<0.05). These results show that occlusion had an effect on mechanical strength of the periodontal fibers during retention periods after experimental tooth movement; therefore, it is suggested that occlusion should be considered while the retainer types and retention period are planned.