• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.38 no.3
• /
• pp.226-233
• /
• 2002

In the field of research of sea keeping quality, much development has been made in recent years using the method of calculation based on the strip theory. It is very important to investigate the hull response of a fishing vessel in waves to ensure the safe navigation and fishing operation in rough seas by preserving excellent sea keeping qualities. For this purpose, the author measured various responses of three fishing vessels in waves using real sea experimental measuring system and analyzed the experimental data The results obtained can be summarized as follow. 1. The amplitudes of pitching motion in the experiments appeared low values with more than one peak occasionally in following sea and quartering sea, and the band width of those was found to be wide relatively. 2. The amplitudes of rolling motion in the experiments appeared high values with only one peak in following sea and quartering sea regardless of ship's tonnage, and the band width of those was found to be narrow relatively. 3. The comparisions of theoretical results with those of experiments for the pitching motions and rolling motion in following sea and quartering sea show that the theoretical values are higher slightly than those of experiments in both directions and the period at which the peak appears in the calculations and the experiments has good agreement approximately 4. The calculated responses of two vessels under a assumed wave of 2.2m height and 5.0sec period showed that the response of pitching motion of ship-A are 2.2 times bigger than those of ship-C in following sea and quartering sea, and the response of rolling motion of ship-A is 4.2 times bigger than that of ship-C in quartering sea.

• Clean Technology
• /
• v.21 no.3
• /
• pp.191-199
• /
• 2015

The SO_x emission from the ship diesel engines will do a negative influence to the human health and the environment. To reduce the negative environmental effect of the SO_x emission caused by the high traffic of ship movements, the SECA (SO_x emission control area) has been set on several province around world to carry out the severe emissions control and to meet the emissions control standard. To cut down the SO_x emission from the ships, the wet type scrubber is being used widely. In this work, we prepared a numerical model to simulate the spray type scrubber to study the motion of liquid droplets in the flow of the scrubber. For the analysis, the CFD (computational fluid dynamics) method was adopted. As a special topic of the study, we designed the wave plate type of mist eliminator to check the carry over of the uncontrolled water droplet to the exhaust. Numerical analysis is divided into two stages. At the first stage, the analysis was done on the basic scrubber without the mist eliminator, and then the second stage of analysis was done on the scrubber with the mist eliminator on several condition to check and compare with the basic scrubber. On the condition of the basic scrubber, 42.0% of the distributed water droplets were carried over to the exhaust. But by adding the designed droplet eliminator at the exhaust of the scrubber, only 3.4% of the distributed water droplets supplied to the scrubber was emitted to the atmosphere.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.6
• /
• pp.731-738
• /
• 2017

Twin-hulls frequently incur structural damage at connecting members between the hull and deck induced by pitching motions during voyages. so, reasonable reinforcement is necessary around vulnerable spots such as corner knuckle, the chine bottom and inner hull. Since guidelines for structural design are not clear, engineers often respond by reinforcing plate thickness, changing stiffener sizes and reducing frame spacing, etc. These members constitute about 85 % of the longitudinal dimensions of the ship, so it is necessary to locally reinforce certain points to minimize weight stress, and also solve construction cost problems while securing the freeboard margin. Therefore, we developed a new program by analyzing the structural design procedures for the twin car-ferries based on Korean Register of Shipping (KR) High Speed Craft Rules, identifying items that need to be added. In order to ensure the reliability of buckling estimations for procedures and design programs, we conducted a comparative study with other standards and confirmed that differences were minimal.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.152-172
• /
• 1992

The ship sailing among waves are suffered the various wave loads that comes from its motion throughout its life. Because there are dynamic, the analysis of ship structure must be considered as the dynamic problem precisely. In the rationally-based design, the dynamic structural analysis is carried out using dynamic wave loads provided from the results of the ship mouton calculation as the rigid body. This method is based on the linear theory assumed low wave height and small amplitude of motion. But at the rough sea condition, high wave height, relatively ship's depth, is induced the large ship motion, so the ship section configulation below water line is rapidly changed at each time. This results in non-linear problem. Considering above situation in this paper, the strength analysis method is introduced for the hull glider among waves considering non-linear hydrodynamic forces. This paper considers that the overall or primary level of the ship structural dynamic loading and dynamic response provided from the non-linear wave forces, and bottom and bow flare impact forces estimated by momentum slamming theory, in which the ship is idealized as a hollow thin-walled box beam using thin-walled beam theory and the finite element method. This method is applied to 40,000 Ton Double-Skin Tanker and attention is paid to the influence of the response of ship speed, wave length and wave height compared with linear strip theory.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.31-41
• /
• 1997

This paper describes a potential-based panel method formulated for the prediction of the steady performance of a waterjet propulsor. The method employs normal dipoles and sources distributed on the solid surfaces such as the impeller/stator blades, hub and duct, and normal dipoles in the shed wakes trailing the impeller and stator to represent the potential flow around the waterjet propulsor. To define a closed boundary surface, the inlet and outlet open boundary surfaces are introduced where the sources and dipoles are distributed. The kinematic boundary condition on the solid boundary surface is satisfied by requiring that the normal component of the total velocity should vanish. On the inlet surface, the total inflow flux into the duct is specified, and on the outlet surface the conservation of mass principle is applied to evaluate the source strength. The solid surfaces are discretized into a set of quadrilateral panel elements and the strengths of sources and dipoles are assumed constant at each panel. Applying this approximation to the boundary conditions leads to a set of simultaneous equations. Systematic numerical tests show that the present numerical method is fast and stable. In order to validate the present method, sample computations are carried out first for the case of a conventional axial flow fan which has a similar geometry as the waterjet propulsor, and then for the case of a waterjet propulsor on which experiments are carried out at KRISO(Korea Research Institute of Ships and Ocean Engineering).