• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.4
• /
• pp.351-355
• /
• 2015

This paper explained the application of a lithium-ion battery energy storage system to electric propulsion ships. The power distribution in electric propulsion ships has low power quality because of the variation in the power consumption of the propulsion motor. For proper operation of the ship, the power quality needs to be improved, and the battery energy storage system is used to solve power-quality problems. The simulation models of electric propulsion ship and battery energy storage systems are constructed on MATLAB/Simulink to verify the improvement in power quality. The proposed system is applied in various scenarios of the propulsion motor state. The power quality achieved by using the battery energy storage system in both voltage and frequency satisfies the standards set by IEC-60092/101.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.1
• /
• pp.8-14
• /
• 2011

RIB(Rigid Inflatable Boat) is widely used for coastal transportation in the commercial use and for ISR(Intelligence, Surveillance, Reconnaissance) in the military use. Since RIB is around 10 meters in length and over 30 knots in speed, its motion characteristics in waves is quite different from a large scale ship. When it turns, large roll occurs and heeling direction is opposite to the large ship's case. Currently, many countries are developing USV(Unmanned Surface Vehicle) of which type is RIB. In order to develop high performance autopilot and way point controller, it is very important to identify RIB's motion characteristics. In this paper, sea trial test results of a 7-meter RIB such as speed, turning, zig-zag, and way point control tests were represented and its resistance and propulsion model was identified by using sea trial data and Savitsky's formula. In addition, the state space model which will be used in the identification of the four-degree-of-freedom dynamics in the next step was formulated and the identification procedure was proposed.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.947-948
• /
• 2007

A superconducting synchronous motor with rotating field coil has been designed. This rotating field coil is composed of high-temperature superconducting(HTS) wire but the stationary armature windings are composed of conventional copper wire. In this paper a 5MW class synchronous motor with rotating HTS coil is designed. This motor is aimed to be utilized for ship propulsion so it has very low-speed. Firstly an air-cored type has been designed, which does not have any iron core both at the field and at the armature teeth. Secondly several iron-cored rotor types are considered to reduce expensive HTS wire cost.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.6
• /
• pp.325-331
• /
• 2022

Hydrogen embrittlement in metals has been a serious issue with regard to structural safety. In this study, molecular dynamics simulations revealed that the aggregation of hydrogen atoms at the crack tips suppresses the dislocation emission and thus results in cleavage fracture. A series of molecular dynamics simulations were performed considering factors such as the concentration of hydrogen atoms, loading rate, and diffusion coefficient. We investigated the conditions that minimize hydrogen embrittlement. The simulation results were consistent with the experimental results and used to quantify hydrogen embrittlement.

• Journal of the Korean institute of surface engineering
• /
• v.57 no.1
• /
• pp.49-56
• /
• 2024

Superhydrophobic surfaces have been expected to be able to provide considerable performance improvements and introduce innovative functions across diverse industries. However, representative methods for fabricating superhydrophobic surfaces include etching the substrate or attaching nanosized particles, but they have been limited by problems such as applicability to only a few materials or low adhesion between particles and substrates, resulting in a short lifetime of superhydrophobic properties. In this work, we report a novel coating technique that can achieve superhydrophobicity by electrophoretic deposition of aluminum nitride (AlN) nanopowders and their self-bonding to form a surface structure without the use of binder resins through a hydrolysis reaction. Furthermore, by using a water-soluble adhesive as a temporary shield for the electrophoretic deposited AlN powders, hierarchical aluminum hydroxide structures can be strongly adhered to a variety of electrically conductive substrates. This binder-free technique for creating hierarchical structures that exhibit strong adhesion to a variety of substrates significantly expands the practical applicability of superhydrophobic surfaces.

• Journal of Service Research and Studies
• /
• v.6 no.2
• /
• pp.23-35
• /
• 2016

Firms should seek greater profits and corporate growth through new businesses. New businesses contribute realizing creative economy that creates good jobs, and expanding the company by securing new markets and creating new profits and growth. However, new business is risky management decision-making to have a high failure rate because it involves the adaptation of new business environment and the burden of new investments, including the uncertainty of success in business. Therefore, innovation strategies play important roles for the new business entry, using product innovation, process innovation, business model innovation, disruptive innovation, and strategic innovation, etc. and company will get huge economic results by pushing them into successful business. It is essential that innovation strategy and IT development strategy along with business strategy of a firm are linked, and their strategic alignment is considered to be a critical success factor for new business success. Hyundai Heavy Industries(HHI) pursued marine engine business for the development of precision machinery industry and shipbuilding industry of Korea, and the company recognized the importance of new business strategy, innovation strategy, and IT strategy inter-linked, and pushed strategic alignment boldly. As a result, HHI won the competition in European and Japanese engine manufacturers and climbed into the world's largest engine manufacturer. This study suggests investigating and analyzing a case that HHI succeeded in marine engine business expansion using strategic innovation strategy as a way of the introduction of CNC machine tools and the development of HEMAPT system.

• Journal of Navigation and Port Research
• /
• v.44 no.4
• /
• pp.283-290
• /
• 2020

BOG (Boil Off Gas) generation is unavoidable in the liquefied hydrogen carrier, and proper measures are necessary to prevent pressure problems inside the cargo tank. The BOG can be used as propulsion fuel for ships, and the remaining parts used for propulsion must be effectively managed, such as in the form of reliquefying or burning. This study proposes an BOG reliquefaction system optimized for a 160,000 m3 liquefied hydrogen carrier with a hydrogen propulsion system. The system comprises a hydrogen compression and helium refrigerant section, and increases the efficiency by effectively using the cold energy of the BOG discharged from the cargo tank. In this study, the system was evaluated through the exergy efficiency and SEC (Specific Energy Consumption) analysis according to the rate of the reliquefaction of the BOG while the hydrogen BOG with a supply temperature of -220℃ entered the reliquefaction system. As a result, it showed SEC of 4.11 kWh/kgLH2 and exergy efficiency of 60.1% at the rate of reliquefaction of 20%. And the parametric study of the effects of varying the hydrogen compression pressure, inlet temperature of the hydrogen expander, and the feed hydrogen temperature was conducted.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.40-51
• /
• 1991

A Propeller design method using the newly developed blade section(KH18), which behaves better cavitation characteristics, is presented. Experimental results for two-dimensional foil sections show that the lift-drag curve and the cavitation-free bucket diagram of the new blade section are wider comparing to those of the existion NACA sections. This characteristic of the new section is particularly important for marine propeller applications since angle of attack variation of the propeller blade operating behind a non-uniform ship's wake is relatively large. A lifting surface theory is used for the design of a propeller with the developed section for a 2700 TEU container ship. Since the most suitable chordwise loading shape is not known a priori, chordwise loading shape is chosen as a design parameter. Five propellers with different chordwise loading shapes and different foil sections are designed and tested in the towing tank and cavitation tunnel at KRISO. It is observed by a series of extensive model tsets that the propeller(KP197) having the chordwise loading shape, which has less leading edge loading at the inner radii and more leading edge loading at the outer radii of 0.7 radius, has higher propulsive efficiency and better cavitation characteristics. The KP197 propeller shows 1% higher efficiency, 30% cavitation volume reduction and 9% reduction of fluctuating pressure level comparing to the propeller with an NACA section. More appreciable efficiency gain for the new blade section propeller would be expected by reduction of expanded blade area considering the better cavitation characteristics of the new blade section.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.6
• /
• pp.697-703
• /
• 2023

As a part of the global industrial efforts to reduce environmental pollution owing to air pollution, regulations have been established by the International Maritime Organization (IMO). The IMO has implemented various regulations such as EEXI, EEDI, and CII to reduce air pollution emissions from ships. They are also promoting measures to decrease the power consumption in ships, aiming to conserve energy. Most of the power used in ships is consumed by electric motors. Among the motors installed on ships, the engine room blower that takes up a significant load, operates at a constant irrespective of demand. Therefore, energy savings can be expected through frequency control. In this study, we demonstrated the efficacy of energy savings by controlling the frequency of the electric motor of the generator blower that supplies combustion air to the generator's turbocharger. The system was modeled based on the output data of the turboharger outlet temperature in response to the blower frequency inpu. A PI control system was established to control the frequency with the target being the turbocharger outlet temperature. By maintaining the turbocharger design standard outlet temperature and controlling the blower frequency, we achieved an annual energy saving of 15,552kW in power consumption. The effectiveness of energy savings through frequency control of blower fans was verified during the summer (April to September) and winter (March to October) periods. Based on this, we achieved annual fuel cost savings of 6,091 thousand won and reduction of 8.5 tons of carbon dioxide, 2.4 kg of SOx, and 7.8 kg of NOx air pollutants on the training ship.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.16 no.1
• /
• pp.81-91
• /
• 2010

IMO(International Maritime Organization) and the Shipping World rave complied with various kinds of international regulations for maritime safety and marine environmental protection, but the main reason of maritime accidents is that developing countries cannot implement maritime safety related regulations. Although Korea has been a member of the "A group" council of IMO, maritime technology transfer records of Korea are not good. To promote the project of official development assistance in Korea, it is required to select the technology which has a high degree of importance in the fields of maritime safety and has a high degree of demand on the transfer to developing countries, and to concentrate on the selected technology. So, it is necessary to draw valuation factors for maritime safety technology and to decide the priority in order among maritime safety technologies on the basis of valuation factors. Because the weights which show the degree of importance among valuation factors are different from factor to factor, interdependent relationship between factors should be considered on evaluation. In this study, the valuation factors were divided into three groups as the maturity of maritime safety technology, the promotion probability of projects and the degree of importance of technology, and the detailed factors of each group were drawn. A model which used Fuzzy AHP and limiting probability to consider the weights of importance and correlation among valuation factors was developed. To adopt this model, nine types of maritime safety technology in the field of maritime safety information were selected and points were scored for each technology through evaluation. In conclusion, first, ENC related technology was scored to be the highest as 0.0139. Second, the point of ship monitoring technology was scored as 0.0133. Last, oil spill response technology was scored as 0.0132.