• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.2
• /
• pp.70-76
• /
• 2000

A numerical study on the viscous flow around a 2-dimensional circulation control foil is carried out for application on the field of naval architecture and ocean engineering. The governing equations are the RANS and the continuity equations. The equations are discretized by finite difference method and MAC method and the pressure poisson equation is calculate by a SOR method and an O-type non-staggered boundary fitted coordinate system which is overlapped near the slot is used to improve the numerical accuracy. Turbulence is approximated by a modified Baldwin-Lomax turbulence model. In the present paper, the Coanda effect on a 2-dimensional foil of a 20% thickness ellipse with modified rounded trailing edge has been numerically studied. The change in drag and lift of the foil with various jet momentums are calculated and compared to the experimental results to show good agreements.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.76-82
• /
• 2017

Since the introduction of electronically controlled engines and electric propulsion ships, the need for an uninterruptible power supply for emergency power supply devices that use batteries has gained importance. The bidirectional converter in such emergency power supply devices is a crucial component. This paper proposes, a topology for an improved DC-DC bidirectional converter that is characterized by a high voltage conversion ratio and low voltage stress of switches. To confirm the performance of the converter, a computer simulation was executed with PSIM software. The conversion ratio of the proposed converter was found to be four times higher than the conventional boost converter in step-up mode and one-fourth that of the conventional buck converter in step-down mode, and the voltage stress of the switches was one-fourth of the high-side voltage. Moreover, the proposed converter was confirmed to be able to distribute equal currents between two interleaved modules without using any extra current-sharing control method because of the charge balance of its blocking capacitors.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.121-126
• /
• 2013

Cycloconverter used as a power conversion device in the speed and torque control system of AC machines has the advantage of a simple control and a large torque at low speed. In addition, because a rectifier, a DC link, and an inverter are not installed, this system is simple and suitable for large power system. If a power conversion device, which is currently used as a propulsion motor of large vessel, is changed into cycloconverter, the system is simplified and then the installation costs can be significantly reduced. However, conventional cycloconverter has the increased harmonics because the power loss is large and the waveform of output voltage is distorted, due to the high-speed switching of power semiconductor devices. In order to improve these shortcomings, this paper describes a phase shifting filter which is composed of two inputs with different phases in the primary side and one output in the secondary one. As the voltage waveforms with two different phases are added and transformed into the secondary side, these outputs are close to sinusoidal waves. Thereby the voltage waveforms, which are applied to the propulsion motors, are improved and total harmonic distortions (THDs) are significantly reduced.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.718-724
• /
• 2017

Considerable efforts have been made to expand the boundaries of domestic offshore plant industries, which have focused on the construction of the structures, to the engineering field. On the other hand, time domain analysis, which is one of the most important areas in designing floating offshore plants, relies mainly on the information given by foreign companies. As an early design of the Dynamic Positioning System (DPS) is mostly conducted by several specialized companies, domestic ship builders need to spend time and money to reflect the analysis into the hull shape design. This paper presents the framework required to analyze time domain performance of floating type offshore structures, which are equipped with DPS. To easily perform time domain analysis, framework generates the required input data for the solver, and is modularized to test the control algorithm and performance of a certain DPS. The effectiveness of the developed framework was verified by a simulation with a model ship and the total time for the entire analysis work was reduced by 50% or more.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.5
• /
• pp.363-372
• /
• 2002

In ship operation, the roll motions can seriously degrade the performance of mechanical and personnel effectiveness. So many studies for the roll stabilization system design have been performed and good results have been achieved. In many studies, the stabilizing fins are used. Recently rudders, which have been extensively modified, have been used exclusively to stabilize the roll. But, in the roll stabilization control system, the control performance is very sensitive to the ship speed. So, we can see that it is important to consider the ship speed in the rudder roll control system design. The gain-scheduling control technique is very useful in the control problem incorporating time varying parameters which can be measured in real time. Based on this fact, in this paper we examine the;$H_{\infty}$-Gain Scheduling control design technique. Therefore, we assume that a parameter, the ship speed which can be estimated in real time, is varying and apply the gain-scheduling control technique to design the course keeping and anti-rolling control system far a ship. In this control system, the controller dynamics is adjusted in real-time according to time-varying plant parameters. The simulation result shows that the proposed control strategy is shown to be useful for cases when the ship speed is varying and robust to disturbances like wind and wave.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.2223-2231
• /
• 2010

Recently, an important physical device of transportation, such as car, railroad, ship and aircraft has changed into electronic control unit. According to accident reports, the most of car accidents are caused by faults of embedded software loaded to computer control unit. The facts implies that the test to find defects in embedded software haven't performed sufficiently. As a result, it is necessary to establish the test procedures of embedded software based on safety assessment criteria. The objective of this proposal is to provide a unit test procedure complied with the safety assessment criteria for the embedded software. In addition, an effective unit testing procedure and defect analysis methods are proposed and a testing procedure using a safety criteria built-in tool is presented.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.69-69
• /
• 2010

최근 컨테이너 선박의 초대형화로 극후물 고장력 강재인 항복응력 460MPa급 고장력강인 EH47이 개발되었다. 두께 80mm의 극후물 용접에서 용접생산성 향상을 위하여 EGW/FCAW로 양면 용접이 검토되고, 입열량은 최대 300kJ/cm의 대입열 용접이 요구된다. 이를 위해서는 강재 및 용접재료 모두 300kJ/cm 용접부 성능이 선급 규격을 만족하여야 함은 물론 마지막 조립단계에서 적용되기 때문에 용접재료의 용접작업성도 매우 크게 요구되고 있다. 먼저 대입열 용접금속에서 요구되는 저온 충격인성($vE_{-20^{\circ}C}{\geq}57J$)을 만족하기 위하여는 용접금속의 미세조직 제어가 필요하며, 특히 조대한 입계페라이트 생성을 억제하고 미세한 입내 페라이트를 균일 분포하는 것이 중요하지만, 이를 위해 용접금속의 소입성이 지나치게 높이면 경화조직인 베이나이트 분율이 증가하여 오히려 용접금속 저온 충격인성을 저하시키므로, 적절한 용접금속의 성분 제어가 중요하다. 한편 용접부는 선급에서 요구하는 최소 강도인 570MPa를 만족하기 위하여 용접금속의 소성구속 현상을 활용하여 용접부 인장강도를 확보 할 수 있음을 확인했다. 이를 위해서는 용접금속의 적정한 경화도 확보가 필요하였다. 전술한 바와 같이 대입열 용접금속 저온 충격인성 확보와 용접부 강도 측면을 고려하여 용접금속 최적의 탄소당량 범위를 제시코자 하였다. 한편 용접재료의 용접작업성은 EGW용접의 용적이행 현상은 자유비행이행으로 이루어지고 있으며 특성상 용접중 용적과 용융지 사이에 많은 순간단락 현상을 동반하고 있으며, 슬래그 유동이 불안정하면 아크 꺼짐 현상도 관찰되고 있다. 따라서, 현장용접시 원할한 용접작업성을 확보할 수 있는 평가 기준으로써 아크 전류 및 전압의 변동 정도를 설정하고, 용접재료의 용접작업성 확보 기준을 제시코자 하였다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.5
• /
• pp.431-437
• /
• 2006

In this paper vector code correlation(VCC) method and an algorithm to promote the image-processing performance in building an effective measurement system using cameras are described far automatically berthing and controlling the ship equipped with side-thrusters. In order to realize automatic ship berthing, it is indispensable that the berthing assistant system on the ship should continuously trace a target in the berth to measure the distance to the target and the ship attitude, such that we can make the ship move to the specified location. The considered system is made up of 4 apparatuses compounded from a CCD camera, a camera direction controller, a popular PC with a built-in image processing board and a signal conversion unit connected to parallel port of the PC. The object of this paper is to reduce the image-processing time so that the berthing system is able to ensure the safety schedule against risks during approaching to the berth. It could be achieved by composing the vector code image to utilize the gradient of an approximated plane found with the brightness of pixels forming a certain region in an image and verifying the effectiveness on a commonly used PC. From experimental results, it is clear that the proposed method can be applied to the measurement system for automatic ship berthing and has the image-processing time of fourfold as compared with the typical template matching method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.11
• /
• pp.1185-1191
• /
• 2014

An integrated ship area network has functionality of remote control and autonomous management of various sensors and instruments embedded or boarded in a ship. For such environment, a wireless bridge is essential to transmit control and/or managing information to sensors or instruments from a central integrated ship area network station. In this paper, one of reliable schemes of In-ship sensor networks using a Grid-based WPAN is proposed. The proposed scheme is based on a novel grid network which allows a multi-path communication, and is robust, energy efficient. The results demonstrate that the proposed Grid-based WPAN outperforms the IEEE 802.15.4 based network in terms of success ratio and power efficiency.

• Journal of Navigation and Port Research
• /
• v.32 no.10
• /
• pp.851-856
• /
• 2008

Construction of large-scale container ports with the productivity improvements in container cranes shortened time of staying port to increase the level of service it harbors efforts accelerated. About container crane system exerted on the input, which is designed to look good performance considering the states feedback control system. The states observer designed of container cranes state variables that are expected to measurement noise or particular measurement signal. In the status of existing research, the feedback gain matrix and the state observer gain matrix are searched by being separated solving. But the feedback gain matrix and the state observer gain matrix are searched by RCGAs at once that be used robust search method in this paper.