• 대한기계학회논문집
• /
• 제13권1호
• /
• pp.140-152
• /
• 1989

본 논문에서는 소형 고속 디젤 분무의 반경 방향의 연류 농도 분포를 고려한 비균질 분무의 분무 선단 도달 거리에 대한 관계식을 유도하고, 비정상 분무인 디젤 분무의 분사 차압-시간 곡선을 입력시킴으로써, 분사 초기 뿐 아니라 전 분사 기간의 분무 선단 도달 거리를 예측할 수 있는 새로운 모델을 제안하여 실험치와 비교 분석하였다. 그리고 분사각과 분열장의 무차원 실험식을 도출하여 계산에 사용하였고 분무 선단 도달 거리의 천이점과 분열장에 대하여 고찰하였다.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.8-22
• /
• 1995

Three dimensional numerical study of non-evaporating and evaporating spray characteristics was performed in a quiescent and motoring condition of direct injection diesel engine. The calculation parameter was breakup model. The breakup models used were Reitz & Diwakar model and TAB model. The modified k-${\varepsilon}$ turbulence model considering the compressibility effect due to the compression and expansion of piston was used. The calculation results of the spray tip penetration and tip velocity using the TAB model showed similar trends comparing with the experimental data. Although the evaporation rate was not nearly affected with the breakup model at the higher injection pressure, in the low injection case, the evaporation rate result using the TAB model became higher than that of R&D model. The evaporation rate was increased with the injection pressure due to the vigorous interaction with the gas field.

• 동력기계공학회지
• /
• 제9권2호
• /
• pp.14-18
• /
• 2005

In this study, the spray characteristics of blended fuels with biodiesel were investigated. The experiments were performed for the effect of mixing ratio and injection pressures on the spray behavior. Conventional diesel fuel and biodiesel fuel and blended fuels were used as test fuels. Through the spray visualization system, composed of a Halogen lamp and High speed camera. The process of spray injection was visualized. Fuel containing biodiesel has different spray pattern on account of the high viscosity and large surface tension. Through this experimental result, we found that, after solenoid driving pulse generates, the increase of injection pressure enables delay time to get shorter, but the increase of mixing ratio makes delay time lengthen.

• 한국분무공학회지
• /
• 제4권2호
• /
• pp.40-46
• /
• 1999

Experimental investigation of unsteady impinging diesel spray on the flat plate have been carried out using high speed camera and Malvern system. The density ratios of ambient gas to diesel fuel were varied using $N_2$ and Ar gas in the case of 14.9, 21.2, 28.4, 35.1, 40.4, and 50.1. With the increase of gas density ratio, the radial penetration is decreased due to the resistance of the ambient gas. With the increase of the gas density ratio and the distance between nozzle tip and flat plate, the height of spray is increased due to the entrance and circulation. With the increase of gas density ratio, SMD is decreased on the nearby position at the center of flat plate, but SMD is increased on the far position. As the distance between nozzle tip and flat plate is increased, SMD is always decreased.

• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.137-146
• /
• 1996

Behaviour of ultra-high pressure diesel spray and its structure in a constant-volume pressure chamber were studied with injection pressure ranging from 35 to 110MPa. Sprays were observed by using the back illumination scattering method and righ angle scattering method. The spray process mechanism were investigated with both photographs. As a result, the spray angle and air entrainment angle was larger as injection pressure and back pressure increase. It becomes clear that mean air-fuel ratio is increased by increasing the injection pressure.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• 한국분무공학회지
• /
• 제14권3호
• /
• pp.117-121
• /
• 2009

Biodiesel fuel has different spray patterns, because viscosity and surface tension of biodiesel fuel are higher than that of diesel fuel. The diesel combustion is strongly controlled by the fuel spray behavior in combustion chamber. So, it was needed to understand the spay characteristics of non-esterification biodiesel fuel. In this study, the spray characteristics of non-esterification biodiesel fuel was investigated to confirm of an effect of WDP. The characteristics of fuel atomization was analyzed with SMD and span factor through laser diffraction particle analyzer (LDPA), and the process of spray injection was visualized through the visualization system composed of a halogen lamp and high speed camera. It was found that injection delay time and SMD of blended fuel with WDP get shoter and smaller than that of non-esterification biodiesel fuel.

• 한국분무공학회지
• /
• 제10권1호
• /
• pp.17-23
• /
• 2005

Even though a relatively complete knowledge base has been established for diesel sprays, much of the knowledge cannot be directly translated to correlate the characteristics of gasoline spray. The macroscopic characteristics of gasoline impingement spray was investigated with photographic and image processing technique by Particle Motion Analysis System. The injector with single hole nozzle diameter of 0.28 mm was used in this experiment and the injection duration was selected as 10 msec. The injection pressure with 0.3, 0.35, and 0.4 MPa, impingement distance or 70, 100 and 130m, impingement angle or 0.15, 30 and $45^{\circ}$ were employed for the variables to affect the spray characteristics of impinging spray. It is clear that there is the analogy on the spray tip penetration between the gasoline impinging jet and diesel free jet. The spray tip penetration of impinging gasoline spray is proportional to the quarter power of the time after start of injection. The maximum height of impinging gasoline spray is also proportional to the quarter power of the time regardless of impingement distance, impingement angle and injection pressure. In addition, the effect of impingement angle on the spray tip penetration is significant according to the time after start of injection, even though there is minor effect in the initial stage of time after start of injection. Moreover, there is no remarkable effect of injection pressure on the spray tip Penetration under the experimental condition used in this study.

• 대한기계학회논문집B
• /
• 제38권9호
• /
• pp.763-771
• /
• 2014

본 연구는 에멀젼연료($diesel/H_2O_2$)의 분무거동특성에 관한 기초 연구로서 에멀젼연료를 제조하여 분무 거동특성에 영향을 주는 연료의 물성치(점도, 표면장력, 밀도)와 연료액적 증발특성을 조사하였다. 또한 에멀젼연료와 디젤연료의 거시적 분무거동특성인 분무선단도달거리, 분무각을 비교 분석하였다. 에멀젼연료의 교반 조건은 디젤 연료와 계면활성제 span 80, tween 80을 각각 9:1로 혼합한 유화제를 제작하여 사용 하였으며 과산화수소의 혼합비율은[EF(Emulsified Fuel)2, EF12, EF22, EF32, EF42, EF52, EF62, EF72, EF82, EF92]로 설정하였고, 분사압력은 400bar, 600bar, 800bar 및 1000bar로 설정하였다. 본 연구의 결과로서 연료의 점도는 과산화수소의 혼합비율이 증가할수록(EF52까지) 점도가 증가하나, 그 이후부터는 점도가 낮아져 기존의 디젤연료와 같은 점도를 가지게 된다. 이는 디젤의 혼합비율이 큰 EF52까지는 교반 시 수중유형(Water in Oil)이 생성되나 과산화수소의 혼합비율이 큰(EF52 이상) 에멀젼연료에서는 유중수형(Oil in Water)이 생성되기 때문이다. 또한 혼합비 변화에 따른 분무거동의 특성(분무선단도달거리, 분무각)의 변화는 크지 않았다.