• Journal of Energy Engineering
• /
• v.2 no.2
• /
• pp.208-214
• /
• 1993

Pyrolysis of bituminous coal has been carried out in a two-stage fixed bed reactor to produce high heating value gas(7000 kcal/N㎥) for industrial or town gas usage. The effects of coke catalyst, pyrolysis temperature (468∼565$^{\circ}C$), and catalytic cracking temperature (700∼850$^{\circ}C$) on the product gas properties from pyrolysis of bituminous coal have been determined. From pyrolysis of Dong Jin coal with coke, the carbon deposition on catalyst is found to be less than 5% of product tar and approximately 15% of total energy iii the parent coal can be recovered as high heating value gas. Oil composition in the product tar from the two-stage pyrolysis is higher than that from low-temperature pyrolysis. The tar produced from pyrolysis below 516$^{\circ}C$ can be easily catalytically cracked but, the tar produced above 565$^{\circ}C$ cannot be cracked easily with catalyst. From the product gas analysis, the catalytic cracking temperature should be maintained below 800$^{\circ}C$ since cracking speed of ethylene increases remarkably with the cracking temperature above 800$^{\circ}C$.

• Journal of Preventive Medicine and Public Health
• /
• v.21 no.2 s.24
• /
• pp.271-283
• /
• 1988

A Fourier transform infrared spectrophotometric method was described for the determination of quartz, mica(sericite) and feldspar(potassium feldspar) in respirable dust in Taebaek area. The results were as follows; 1) The concentration of minerals were determined from the intensity of absorption peak of quartz at $799cm^{-1}$, sericite at $539cm^{-1}$, and potassium feldspar at $648cm^{-1}$ respectively. 2) The precision(C. V. %) for the quartz determination was $7.70{\pm}2.68%$ from 10 to $200{\mu}g$ of quartz. 3) The precision for the sericite determination was $16.34{\pm}6.82%$ from 30 to $500{\mu}g$ of serictite. 4) The precision for the potassium feldspar determination was $5.28{\pm}1.74%$ from 30 to $500{\mu}g$ of potassium feldspar. 5) The concentration of respirable dust in Taebaek area was $4.90{\pm}3.29mg/m^3$ (0.4-93.7%), percent quartz was $1.80{\pm}4.14%$ (0.01-20.56%), percent sericite was $11.37{\pm}6.43%$ (0.00-29.69%), percent potassium feldspar was 8.15% (n=7, 3.41-19.70%). 6) The difference of respirable coal dust, quartz, and sericite concentrations in drilling, coal cutting, hauling and seperating was significant respectively (p<0.05).

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.2
• /
• pp.15-25
• /
• 2003

Time Domain Refletometry, or TDR, is a remote sensing electrical measurement technique that has been used for many years to determine the spatial location and nature of various objects, especially in the United States of America and Australia at mining industry. Since early on 1990, the TDR techniques have been applied to the geotechnical engineering such as : deformation measurement of rock slope and landslide, monitoring of ground water content and ground water level change, investigation of ground contamination and its movement. The first application of this technique, in 1996, to the domestic area is to determine the possibility of ground settlement caused by subsidence from abandoned underground mines at the Tongri and Gosari in Gangwon-d. In this paper, through the results of analysed deformation data between conventional measurements and the TDR, it was concluded that the TDR technique is a useful instrumentation method for the prediction of ground deformation.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.41-46
• /
• 2010

The low alloy-steel material(1.0Cr-0.5Mo, SA213T12), which has widely been used for the waterwall tube in the conventional power plant, do not have enough creep rupture strength for waterwall tubes of the Ultra-supercritical(USC) boilers. According to this reason, the high-strength low alloy-steel(2.25Cr-1.0Mo, SA213T22) has newly been adopted for the waterwall tube in the USC boilers. This paper presents failure analysis on weld-joint of the waterwall tubes in USC boilers. Visual inspections were performed to find out the characteristics of the fracture. Additionally both microscopic characteristics and hardness test were carried out on failed tube samples. Failures seem to happen mainly because the welding process has not been conducted strictly.(preheating, P.W.H.T and so forth). Thus, this paper has the purpose to describe the main cause of the poor welding process and to explain how to prevent similar failures in those weld-joints.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2004.05a
• /
• pp.341-346
• /
• 2004

In the present work, for various energy and electricity generating systems to be compared in view of integrated social impacts, nuclear, coal-fired, heavy oil-fired, and LNG, and hydroelectricity systems are considered as electricity generating options. The following assessment factors are selected: economic effect, health effect, environmental effect, and benefit at the national level. As a preliminary study, these factors are represented as power generation cost, estimated mortality, Carbon Dioxide gas emission, and fuel supply stability, respectively. For integrated representation of a multi-criteria decision-making (MCDM) problem, radar charts are introduced to facilitate a comparative recognition of estimates. In the near future, based on the estimates, a MCDM methodology for both qualitative and quantitative comparison will be developed.

• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.784-790
• /
• 2010

VOCs such as acetone, benzene, toluene, ethylbenzene were adsorbed in a fixed-bed adsorber using zeolite synthesized from coal fly ash and 4 kinds of activated carbon at 101.3 kPa. The adsorber was operated batchwise with the charge of 5 g adsorbent to obtain the breakthrough curve of VOCs. Experiments were carried out at $40^{\circ}C$, nitrogen flow rate of $70cm^3/min$ and sparger temperature of $30^{\circ}C$. The deactivation model was tested for these curves by combining the adsorption of VOCs and the deactivation of adsorbent particles. The observed values of the adsorption rate constant and the deactivation rate constant were evaluated through analysis of the experimental breakthrough data using a nonlinear least square technique. The experimental breakthrough data were fitted very well to the deactivation model than the adsorption isotherm models in the literature. Also, adsorption capacities of adsorbents were obtained from the breakthrough curve to observe the correlation between adsorption capacity and the physical properties of VOCs.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.658-663
• /
• 2010

With petroleum reserves dwindling, interest has been increasing worldwide in Fischer-Tropsch synthesis (FT) as a method of producing synthetic liquid fuels and chemicals from coal, natural gas or biomass. In general, FT synthesis is operated through the gas phase fixed-bed reaction system. Recently, there are lots of study in supercritical fluid due to unique characteristics such as the quick diffusion of reactant gas, effective removal of reaction heat, and the in-situ extraction of high molecular weight hydrocarbon, such as wax. In this study, our major aim is to obtain a deeper insight into the effect of the type of support on the reaction performance over a supported cobalt catalyst in a fixed bed reactor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.6
• /
• pp.67-74
• /
• 2013

IGCC(Integrated Gasification Combined Cycle) system is candidates which can solve the environmental problems including global warming, since it can be easily combined with CCS(Carbon Capture System). In this research, combustion instability characteristics were studied at various fuel which are composed of $H_2/CH_4/CO$ mixture. Mode analysis for instabilities observed experimentally was conducted and the linearly increasing tendency of frequency was observed as the hydrogen content in fuel increases.

• Journal of the Korea Society for Simulation
• /
• v.20 no.4
• /
• pp.49-58
• /
• 2011

It is required that a developed control system should be verified using simulator in terms of functionality and reliability prior to application to a power plant that is a very critical facility in the industry. In this paper, the control model for turbine bypass system was developed for power plant simulator. In order to develop the control model for turbine bypass system, the tool that can be used to implement turbine bypass control logic was developed based on the turbine bypass control system manual. The developed tool was merged into the simulator development environment. The functionality of the developed tool was verified via the simulation based on the each function block specification. The HP turbine bypass pressure control logic was implemented using the developed tool and was integrated with process models and other control models such as boiler control model, turbine control model and boiler feed water pump turbine control model for 500 MW korean standard type fossil power plant. Finally, the validity of the developed control model was shown via simulation result under the integrated simulation environment.

• Resources Recycling
• /
• v.14 no.2
• /
• pp.56-61
• /
• 2005

Economic feasibility for retrofitting the wet bottom ash handling system to the dry system in a existing 500MW${\times}$2 units pulverized coal thermal power plant in Korea was studied. Replacing to the dry system requires the initial capital costs of 13,415,127,000\, and saves the operating costs of 935,345,000\ per year. Economic analyses based on these results showed that the initial capital cost would not be recovered within the service life of the facilities at the interest rate of 10%, and the internal rate of return of 5.6% were obtained. Thus, the retrofitting to the dry system was not economically favorable in the current condition. However, the retrofitting would be profitable when the ash disposal cost and ash selling price were increased over 15,000\/MT or 17,000\/MT, respectively.