• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.624-628
• /
• 2000

As a power durable-electrode in SAW filter, Al-1%Cu/tungsten nitride multi-layer thin film was fabricated by magnetron sputtering process. Tungsten nitride films had the amorphous phase at the nitrogen ratio, R, ranging from 10~40%. The amorphization could be controlled by nitrogen ratio, R= $N_2$/($N_2$+Ar) as a sputtering process parameter. Residual stress in tungsten nitride abruptly decreased with the formation of amorphous phase. Al-1%Cu thin film was deposited on the amorphous tungsten nitride. After the multi-layed thin film was annealed for 4 hours at 453K, the resistivity decreased as $3.6{\mu}{\Omega}-cm$, which was due to grain growth reduced crystal defects.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.367-374
• /
• 2002

Electrical characteristics of crystalline polymer composites filled with nano-sized carbon black particle were studied. The developed composite system exhibited a typical positive temperature coefficient resistance (PTCR) characteristic, where the electrical resistance sharply increased at a specific temperature. The PTCR effect was sometimes followed by a negative temperature coefficient resistance (NTCR) feature with temperature, which seemingly caused by the coagulation of nano-sized carbon black particles in the excessive quantity. The PTCR temperature was controlled by the carbon black content and the external voltage. The change of electric conductivity was shown as a function of carbon black content, and the resistance was constant when the carbon black content was over 20 wt%. The room-temperature resistance was maintained by a repeated heating and cooling. The excellent PTCR characteristic was demonstrated by the low resistance in the initial stage and the instantaneous heating capability.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1271-1278
• /
• 2007

A novel frequency multiplier using composite right/left-handed transmission line is proposed. The left-handed transmission line in the proposed frequency multiplier suppresses the fundamental component($f_0$), while the composite right/left-handed ${\lambda}/4$ open stub diminishes unwanted harmonics. Due to the combination of the left-handed transmission line and composite right/left-handed ${\lambda}/4$ open stub, the only desirable multiplied frequency component such as 3 $f_0$ and 4 $f_0$ are obtained at the output port excellently. For the example of the proposed design, frequency multipliers are designed at 1 GHz of $f_0$ and measured. The measured output power of 3 $f_0$ and 4 $f_0$ is -5.67 dBm and -6.43 dBm, respectively, when the fundamental input power was 0 dBm.

• Elastomers and Composites
• /
• v.24 no.4
• /
• pp.276-289
• /
• 1989

This study deals with both effects of inorganic fillers to vulcanized rubbers such as NR, CR, EPDM, NBR & SBR and inorganic characteristics of domestic fillers in comparision with hard clay produced in the USA. The results were as follows. 1. Main ingredient of domestic clay "Ha-dong clay" was Halloysite, "No-ha Island" was Pyrophyllite with $\alpha$-Quartz, and both of "Hard clay" & "Hwa-soon clay" were proved to be Kaolinite by XRD, DT-TGA and chemical analysis by XRF. 2. Tensile strength value of SBR compounded with these fillers, was Hard clay $146kg\;f/cm^2$, Kaolinite $123kg\;f/cm^2$, Pyrophyllite $82kg\;f/cm^2$, Halloysite $80kg\;f/cm^2$, precipitated $CaCO_3\;27kg\;f/cm^2$, and ground $CaCO_3$ was $21kg\;f/cm^2$. These results showed the increase of seven times according to filler species. 3. The physical properties of non-crystalline rubbers, such as SBR, NBR & EPDM, compared with NR & CR, have been considerably changed according to crystalline phase, particle size, shape and surface structure of fillers. Especially, tensile strength value in case of SBR & EPDM, was differentiated about 1.5 times by the particle size of fillers. 4. In SBR, physical properties of rubber compounded with Kaolinite which was surface treated with fatty acid and silane, almost approach to the value of hard clay. 5. Delayed cure time of Kaolinite and decrease of rubber properties by $CaCO_3$ can be improved by blending kaolinite & $CaCO_3$ in the ratio of 2:1.

• Spatial Information Research
• /
• v.18 no.3
• /
• pp.85-94
• /
• 2010

This study presented a method to allocate RFID reader sites for the weekly no driving day program. In resent years, three metropolitan cities begin to operate the system to resolve the traffic jam, air pollution, and oil cost, which is expected to be operated across the country in a few years. In this regard, the accurate verification of the observance of the cars which are participated in the system is needed so that the more benefits are rewarded to observing participants but not violating ones. Thus, this study distinguished road sections where the system of the Daegu metropolitan city cannot determine the observance of the participated cars when the cars detour the RFID readers by employing a set of data from the traffic census, digital maps, and terrestrial photographs of the superstructures on the roads. Then, the appropriate sites for additional RFID readers were determined based on those sections in the road network and the types of the road superstructures.

• Spatial Information Research
• /
• v.18 no.3
• /
• pp.73-83
• /
• 2010

This study presents a method to segment an image, employing the statistics observed at each pixel location across sequential frame images. In the acquisition and analysis of spatial information, utilization of digital image processing technique has very important implications. Various image segmentation techniques have been presented to distinguish the area of digital images. In this study, based on the analysis of the spectroscopic characteristics of sequential frame images that had been previously researched, an image segmentation method was proposed by using the randomness occurring among a sequence of frame images for a same scene. First of all, we computed the mean and standard deviation values at each pixel and found reliable pixels to determine seed points using their standard deviation value. For segmenting an image into individual regions, we conducted region growing based on a T-test between reference and candidate sample sets. A comparative analysis was conducted to assure the performance of the proposed method with reference to a previous method. From a set of experimental results, it is confirmed that the proposed method using a sequence of frame images segments a scene better than a method using a single frame image.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.2
• /
• pp.138-147
• /
• 1994

The compressive strength of horizontal joints in precast concrete large panel structures depends on parameters such as grout and panel strength, detail of joint, joint moment, width of grout column, and etc. 44 specimens were tested to investigate the effects of parameters that influence the compressive strength of horizontal joints. The design formula specified in Korean Cock for compression horizontal joints must be reviewed, because it was based on the test results of the joint types not used in Korea. In this study comparing the test results, there fore, the validity of the design formulas was evaluated and a suitable formula was proposed to predict the ultimate strengths of compression horizontal joints. The increase of ultimate strengths was not observed, even if confined the horizontal displacement of slabs and reinforced the wall edge, when the grout strength is lower than panel strength. From the comparison of test results and those by the proposed formula, it was shown that proposed formula was suitable to predict the ultimate compressive strength of horizontal joints.

• Magazine of the Korea Concrete Institute
• /
• v.6 no.1
• /
• pp.111-119
• /
• 1994

The strength of vertical joints of precast concrete large panel structures depends on the many factors, such as the bond strength of grout concrete (or mortar), the interlocking of the shear keys, the dowel action of horizontal bars. Many experimental studies have been conducted to in vestigate the shear strength of the vertical joints. In domestic, a few design formulas to predict shear strength of the vertical joint were proposed by some investigators, but formulas were based on limited experimental results. The objective of this paper is to propose a suitable formula for the shear strength of vertical joints with 94 vertical joints experimental data using the modified Mohr-Coulomb's 4ield theory and regression analysis. From the comparison of the proposed formula with others, it is shown that the proposed formula can be used economically for the design of vertical joints.

• Korean Institute of Interior Design Journal
• /
• no.25
• /
• pp.229-235
• /
• 2000

Although Frank Lloyd Wright represents himself as one of the greatest American master architect, the master architects contribution towards the advancement in the modern history of architecture goes beyond just creating landmark buildings. Through out his life, he was the leading architect not only in the area or architectural design but showed his talent in interior architecture, furniture, fabric, lighting fixture, art glasses, tablewares, silver wares as well as in graphic design which should cover all the elements related to the "total design" in architecture. As seen in his architectural design, the "total design" concept also reflects both beauty and logic of the nature and strengthens his theory of the organic architecture design. The research began with finding out the relationship between his architecture, nature and the supporting design elements mentioned above. the purpose of the research is to analyze the relationship of the spatial organization and the design elements in Frank Lloyd Wrights architectural works from the point of "total design" view and provide the valuable guide line for the development of the modern interior design. His design theory, based on the fundamental ideas of the nature, his organic architecture design, and reference materials to support total design concept will be discussed on chapter 2. And on chapter 3, application of the total design in his actual project will be analyzed. The data and analyzation have been completed based on written references and actual visit to the project sites. Frank Lloyd Wright placed highest value on the human beings and enjoyed presenting new ideas and forms to create better environment for the humans through his architecture and interior design projects. While he was presenting new ideas he continued to support design for democracy which has close relationship to the new frontier spirit of America. He was the master architect for the general society with accurate understanding of the life style of the public with design sensitivity shown in his concept of the total design.s concept of the total design.

• Korean Institute of Interior Design Journal
• /
• v.19 no.6
• /
• pp.121-128
• /
• 2010

Interior design education has been developed rapidly since the discipline established in Korea in 1980s but unfortunately the development was without any progressive transition until 1990's. When Korean Institute of Interior Design/KIID inaugurated in 1992, interior design education and related research activities began to be intensified. Despite its effort, there were still confusion about the discipline as there were many similar discipline tracks (architecture, design, fine art, & home economic, etc.) each having an own definition of interior design and introducing different aspects of educating the subject. Education program for interior design still not sufficiently supporting the needs of today's rapidly changing industry nor to prepare the diverse needs of the client. In order for interior design major to be effective in the future and fulfill the needs of current industry development within our society, re-evaluation of our current interior design educational programs in Korea is important. This study will be the beginning of a research series. As the first part of the research series, this particular study has been focused on reviewing of current status of interior design majors in the nation and its current condition. While making suggestion for the changes in curriculum, the following points will have to be considered as basic principle. First, understanding the duality of technology and design to accommodate the contents of design discipline. Second, understanding the need of practice and theory combined for practical education. And lastly, considering ways to adopt the human experience in order to develop creativity in oneself. The focus of this research is only on the interior design discipline, and research method as the following; first, analyze current status by reviewing admission data for 2010. Second, process a survey regarding the interior design education and practice-related issues in admissions and collect opinions from educators and professional designers in the field. Thirdly, with reference to previous studies, suggestions will be made for the discipline to be effective in the field. As mentioned earlier, this study series will continue and develop to suggest improvement in interior design program as well as to provide curriculums for students get ready for the industry with more up-to-date knowledges and creativities.