• Magazine of the Korean Society of Agricultural Engineers
• /
• v.29 no.2
• /
• pp.64-73
• /
• 1987

효과적인 모래의 다짐 방법으로 진동에 의한 방법이 널리 사용되고 있다. 이 연구의 목적은 모래의 진동 다짐시 영향을 주는 인자의 개별적인 효과를 분석하고 가 인자들이 복합되어 진동다짐에 주는 효과를 분석하는 것이다. 이 연구에서는 진동시간 가속도 과도화중 염수비 시료의 다짐전 밀도등을 변화시켜가며 진동테이블 위에서 제작된 시료를 다짐하였고 시험결과는 상대밀도의 변화애 의하여 분석하였다 진동다짐의 효과는 다짐가속도 진동수 및 모래의 정도에 따라 변하며 과도하중이나 진건은 비교적 적은 영향을 주는 인자였다. 가속도가 1g 보다 큰경우 다짐효과는 진동이 시작되는 초기에 발생하였고 그 후는 면밀하게 진동효과가 나타났다. 효과적인 다짐을 위하여는 최적가속도와 최고 과도하중의 선택이 중요하며 최적치보다 큰경우는 다짐의 효과가 감소한다. 건조된 모래와 포화된 모래 모두 같은 최적가속도에서 최대의 다짐효과를 나타냈다. 각 인자 즉 가속도 진동수 단위 중량 영수비, 균등계수, 유효압경, 과도하중, 및 진동시간등의 효과를 복합하여 진동다짐의 효과를 상대밀도의 변화로 나타낼경우$\Delta$DR=38.0∧0.14 의 관계를 얻었다.

• Geotechnical Engineering
• /
• v.11 no.4
• /
• pp.37-48
• /
• 1995

The dynamic behavior of dry sand under different vibration conditions is studied through laboratory experiments. Sinusoidal and random vibration experiments of sand are carried out in vertical direction under various surcharge loads. Five different sand samples are selected for the azperiment. They are composed of four different -size samples of particles and one sample which is simulated the field condition. In case of sinusoidal vibration, the change in relative density is measured with acceleration levels. To produce an acceleration, the vibration amplitude is maintained within the range of 0.4mm~0.6mm and the vibration frequency is changed within the range of 3Hz~40Hz. In case of random vibration, the combined sinusoidal acceleration is produced by a random vibration generator and the change in relative density is measured by an accelerometer. Based on the experimental results, it is found that the sandy soil is compacted to 94%~99% of relative density by vertical acceleration and the peak acceleration producing the maximum relative density is proportional to the difference between maximum and minimum void ratios. It is also found that the effect of surcharge loading : the greater the surcharge loading, the larger the change in relative density and the greater the acceleration required to change the relative density.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.84-92
• /
• 1997

Among the various sources of vehicle interior noise, this paper concerns the road induced noise ; the identification of its transfer path by using experimental method. Multiple input and single output model is taken as a noise generation model. Because it is impossible to measure the road imput forces directly, the acceleration signals are measured on four axle;three directions for each point. By considering the cross correlations of input signals, four uncorrelated source groups are taken. Multiple coherence function is employed to investigate the contribution of each group. In addtion, to identify the detailed path through the suspension systems, the contributions of all possible paths are ranked by using the coherence functions between interior noise and the relative accelerations of connections such as bushings and mountings. Measurements are performed with passenger vehicle traveling on concrete and asphalt roads at 60㎞/h.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.4
• /
• pp.47-60
• /
• 1999

The stability and efficiency of structural control systems depend on the accuracy of mathematical model of the system to be controlled. In this study, state equation models of a small scale test structure and an AMD(active mass damper) are obtained separately using OKID(observer/Kalman filter identification) which is a time domain system identification method. The test structure with each floor acceleration as outputs is identified for two inputs - the ground acceleration and the acceleration of the moving mass of AMD relative to the installation floor - individually and the two identified state equation models are integrated into one by model reduction method. The AMD is identified with the motor control signal as an input and the relative acceleration of the moving mass as an output, and it is shown that the identified model has large damping ratio and phase shift. The transfer functions and the time histories reconstructed from the identified models of the test model and the AMD match well with those measured from the experiment.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.797-804
• /
• 2003

본 연구에서는 진동대 실험을 실시하여 매립지에서 널리 사용되고 있는 지오멤브레인과 지오텍스타일 사이의 동적 접촉 마찰 특성을 살펴보았다. 연직응력, 진동 주파수, 건조/수침 상태의 영향에 대해서 평가하였으며, 또한 지오멤브레인과 지오텍스타일 사이의 상대적인 미끄러짐의 정도를 측정하였다. 실험 결과, 지오멤브레인과 지오텍스타일 사이를 통해 전달되는 한계 가속도(limited acceleration)가 있음을 확인할 수 있었으며, 이를 통해 지오멤브레인과 지오텍스타일 사이의 동적 접촉 마찰각을 산정할 수 있었다. 이러한 가속도는 수침상태의 경우 건조상태보다 더 작게 산정되었으며, 변위의 경우 수침상태에서 더 크게 발생함을 관찰하였다. 또한 실험조건에 따라 지오멤브레인과 지오텍스타일 사이에 발생하는 상대적인 미끄러짐의 정도가 다르게 측정되었다. 본 연구에서는 지오멤브레인과 지오텍스타일 사이의 slip equation을 제안하였으며, 이 식을 통해 주어진 가속도와 주파수에서 지오멤브레인과 지오텍스타일 사이를 따라 발생되는 최대 미끄러짐의 정도를 예측 가능하게 하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.8
• /
• pp.113-119
• /
• 2000

There are two major factors which affect the cam design : the pressure angle and the radius of curvature, Cam shape will have an instantaneous radius of curvature at every point. Even though the design constraint of the pressure angle has been satisfied the follower may still not complete the desired contact motion. If the radius of the follower roller is larger than the concave(negative) radius on the cam it occurs the gap between the cam and the follower roller at the contact point. And also if the curvature of the pitch curve of the cam is too sharp the cam profile may be undercut. This paper proposes a new approach which uses the relative velocity of the follower roller parallel to the tangent line at the contact point on the cam surface for determining the pressure angle and the relative acceeration for determining the radius of curvature.

• Journal of the korean Society of Automotive Engineers
• /
• v.26 no.2
• /
• pp.23-26
• /
• 2004

일반적인 기구학의 개념은 기계를 구성하는 부품의 상대운동을 연구하는 학문이다. 즉, 기구학은 기계를 구성하는 부품의 강성이나 힘 등은 배제하고 단지 기계를 구성하는 부품의 서로 상대적인 운동관계만을 연구하는 학문이다. 따라서 기구학 해석에 있어서도 변위, 속도, 가속도만을 연구하게 되며, 해석방법에 있어서도 과거에는 도식적인 방법을 사용했으나 최근에는 컴퓨터를 이용한 방법이 보편화되어 있다.(중략)

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.2
• /
• pp.31-35
• /
• 2000

An nonlinear observer-based longitudinal control law for vehicles is presented in this paper. It is assumed that for vehicle i knows only the distance between vehicle i and the preceding vehicle, i-1. An nonlinear state observer for vehicle I is developed to estimate the velocity and acceleration of the preceding vehicle, i-1. The communication of the position, velocity, and acceleration information is not used in the proposed method. It will be shown by mathematical analysis that the longitudinal control of vehicle can be implemented without an communication of the informations. It will be proven that the observation errors of the nonlinear states converge to zero asymptotically. To show the effectiveness of the proposed method, the simulation results are presented for the longitudinal control of the vehicle.

• Water for future
• /
• v.29 no.1
• /
• pp.163-179
• /
• 1996

Flood flow characteristics of the Han River (from Goan to Indo Bridge) are analyzed using 1-dimensional St. Venant equations. NETWORK, a finite difference model, is used to calculate each term (local acceleration term, convective acceleration term, pressure force term, gravity force term, and friction force term) of the momentum equation and to analyze the flow characteristics. By the result of the study, as the general characteristics of flow in a channel that acceleration terms are very small and the other three terms are much greater is presented, three terms(pressure force term, gravity force term, friction force term) are to be main terms which decide the characteristics of flow. Specially in this region the acceleration term is noted so large that it cannot be ignored according to the shape of hydrograph and the region.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.265-275
• /
• 2003

In this study, shaking table tests were conducted to estimate dynamic interface properties between geosynthetics such as geomembrane, geotextile and geosynthetic clay liner. Accelerations of both shaking table and upper box, and relative displacements between geosynthetics under dynamic loading were measured. Also, the influence of normal stress, frequency of excitation and dry/wet conditions were investigated through the analyses of test results. from the test results, it was found that there is a limited acceleration below which dynamic farce can be transmitted between geosynthetics without the loss of horizontal acceleration. Dynamic interface friction angle between geosynthetics could be calculated through the limited acceleration. Relative displacements induced along geosynthetic interfaces under dynamic loading were not consistent depending on the type of interface and test conditions. The maximum slip displacements between geosynthetics are normalized and normalized slip equations were developed for each interface. By using the normalized slip equation, maximum slip displacements for the geosynthetic interface could be predicted for the given base acceleration and frequency of excitation.