• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.93-93
• /
• 2003

• Composites Research
• /
• v.30 no.2
• /
• pp.116-125
• /
• 2017

The purpose of this study is to develop silicon carbide fiber showing an excellent mechanical properties under highly oxidative conditions at high temperature. Polycarbosilane(PCS) as a preceramic precursor was used for making the SiC fiber. PCS fiber was taken by melt spinning method followed by melting the PCS at $300{\sim}350^{\circ}C$ in N2 gas. The Curing of PCS fiber was carried out in air oxygen chamber, prior to high temperature pyrolysis. Degree of cure was calculated by characteristic peak's ratio of Si-H to $Si-CH_3$ in FT-IR spectra before and after curing of PCS fiber. The properties of SiC fiber was affected greatly by the degree of cure. The SiC fiber produced by controlling fiber tension during heat treatment showed good properties. The SiC fiber exposed to $1000^{\circ}C$ at air from 1 min. up to maximum 50 hrs showed around 60% reduction in tensile strength. We found that large amount of carbon content on the fiber surface after long-term exposure has resulted in lower tensile strength.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.619-625
• /
• 2008

The effects of thermal cycling on residual stresses in both inorganic passivation/insulating layer that is deposited by plasma enhanced chemical vapor deposition (PECVD) and organic thin film that is used as a bonding adhesive are evaluated by 4 point bending method and wafer curvature method. $SiO_2/SiN_x$ and BCB (Benzocyclobutene) are used as inorganic and organic layers, respectively. A model about the effect of thermal cycling on residual stress and bond strength (Strain energy release rate), $G_c$, at the interface between inorganic thin film and organic adhesive is developed. In thermal cycling experiments conducted between $25^{\circ}C$ and either $350^{\circ}C$ or $400^{\circ}C$, $G_c$ at the interface between BCB and PECVD $ SiN_x $ decreases after the first cycle. This trend in $G_c$ agreed well with the prediction based on our model that the increase in residual tensile stress within the $SiN_x$ layer after thermal cycling leads to the decrease in $G_c$. This result is compared with that obtained for the interface between BCB and PECVD $SiO_2$, where the relaxation in residual compressive stress within the $SiO_2$ induces an increase in $G_c$. These opposite trends in $G_cs$ of the structures including either PECVD $ SiN_x $ or PECVD $SiO_2$ are caused by reactions in the hydrogen-bonded chemical structure of the PECVD layers, followed by desorption of water.

• Journal of the Korean Chemical Society
• /
• v.52 no.4
• /
• pp.387-393
• /
• 2008

• Composites Research
• /
• v.29 no.4
• /
• pp.194-202
• /
• 2016

A graphene film, two-dimensional carbon sheet, is a promising material for future electronic devices and so on. In graphene applications, the effect of substrate on the atomic/electronic structures of graphene is significant, so we studied an interaction between graphene film and substrate. To study the effect, we investigated the graphene films grown on Ni substrate with two crystal face of (111) and (100) by Raman spectroscopy, comparing with graphene films transferred on $SiO_2/Si$ substrate. In our study, the doping effect caused by charge transfer from Ni or $SiO_2/Si$ substrate to graphene was not observed. The bonding force between graphene and Ni substrate is stronger than that between graphene and $SiO_2/Si$. The graphene films grown on Ni substrate showed compressive strain and the growth of graphene films is incommensurate with Ni (100) lattice. The position of 2D band of graphene synthesized on Ni (111) and (100) substrate was different, and this result will be studied in the near future.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.597-600
• /
• 1999

By periodically varying the current density and etching time during anodic oxidation of crustalline silicon wafers in 15% HF-ethanol solution, we obtained porous silicon multilayers which have periodically varying refractive index. We fabricated the porous silicon microcavity (PSM) which consist of porous silicon multilayers (I), active layer of porous silicon, and porous silicon multilayers (II) and investigated its physical properties. The AFM (Atomic Force Microscope) measurement from the cross section of multilayers (I and II) shows uniformity of high refractive index and low index layers as well as the active layer. We observed the characteristics of Bragg reflector when the thickness of layers was 1/4 and the thickness of active layer was twice of the effective wavelength, which can be used as a filter for specific wavelength. We found the emission characteristic from the PSM, which FWHM (full width half maximum) was considerably decreased and emission intensity was increased.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1992.05a
• /
• pp.33-34
• /
• 1992

• 전기의세계
• /
• v.59 no.2
• /
• pp.18-23
• /
• 2010

• Proceedings of the Korean Journal of Food and Nutrition Conference
• /
• 2000.12a
• /
• pp.56-56
• /
• 2000

대두유를 기초로한 튀김유에 capsicum, butter flavor, 규소수지를 각각 0.20, 0.15%(w/w) 및 10ppm 처리하여 가열안정성의 향상 및 육두향 약화에 효과가 있는 것으로 확인 되었다. 즉, capsicum과 규소수지를 병행처리한 튀김유는 185$\pm$2$^{\circ}C$의 온도조건 하에서 3시간 동안 연속적으로 열처리할 경우 AV 및 SP가 각각 무처리군의 0.385, 22$0^{\circ}C$에 비하여 크게 향상된 0.301, 232$^{\circ}C$를 나타내었다. 이러한 효과는 capsicum의 항산화 효과와 함께 소포제의 일종인 규소수지의 작용에 따라 가열처리에 따른 튀김유의 표면적 팽창을 방지하여 유리지방산 생성 및 연기발생을 억제한데 따른 효과인 것으로 판단 되었다. 또한. 0.15%(w/w)의 butter flavor 처리에 따라 튀김유 및 튀김물에서 발생하는 육두향 및 기름타는 냄새를 막아주는 효과가 인정되어 새로운 형태의 튀김유제품 생산이 가능할 것으로 기대 되었다.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.2
• /
• pp.121-131
• /
• 2014

Due to the high UV light scattering effect of Zinc oxide (ZnO), it is frequently used in sunscreen skincare products. Recently ZnO coated with silica has been used in cosmetics to improve UV protection, texture, decreased photocatalytic activity, dispersibility and stability of the skin care product. In this study, we developed a ZnO composite powder coated with silica for the future application to skincare products to block UV rays that could cause photoaging. To improve consumer's satisfaction rating, we used ZnO microparticles which are widely used in the cosmetics industry. The silica was coated using hydrothermal method with sodium silicate and acid hydrolysis. UV protection of the composite powder was analyzed by UV-Vis and in-vitro test and the advantages for practical use of this powder as a skincare product were determined.