• Geophysics and Geophysical Exploration
• /
• v.13 no.1
• /
• pp.80-87
• /
• 2010

This study was conducted to develop a reservoir modelling workflow to reproduce the heterogeneous distribution of effective permeability that impacts on the performance of SAGD (Steam Assisted Gravity Drainage), the in-situ bitumen recovery technique in the Athabasca Oil Sands. Lithologic facies distribution is the main cause of the heterogeneity in bitumen reservoirs in the study area. The target formation consists of sand with mudstone facies in a fluvial-to-estuary channel system, where the mudstone interrupts fluid flow and reduces effective permeability. In this study, the lithologic facies is classified into three classes having different characteristics of effective permeability, depending on the shapes of mudstones. The reservoir modelling workflow of this study consists of two main modules; facies modelling and permeability modelling. The facies modelling provides an identification of the three lithologic facies, using a stochastic approach, which mainly control the effective permeability. The permeability modelling populates mudstone volume fraction first, then transforms it into effective permeability. A series of flow simulations applied to mini-models of the lithologic facies obtains the transformation functions of the mudstone volume fraction into the effective permeability. Seismic data contribute to the facies modelling via providing prior probability of facies, which is incorporated in the facies models by geostatistical techniques. In particular, this study employs a probabilistic neural network utilising multiple seismic attributes in facies prediction that improves the prior probability of facies. The result of using the improved prior probability in facies modelling is compared to the conventional method using a single seismic attribute to demonstrate the improvement in the facies discrimination. Using P-wave velocity in combination with density in the multiple seismic attributes is the essence of the improved facies discrimination. This paper also discusses sand matrix porosity that makes P-wave velocity differ between the different facies in the study area, where the sand matrix porosity is uniquely evaluated using log-derived porosity, P-wave velocity and photographically-predicted mudstone volume.

• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Archives of design research
• /
• v.13 no.1
• /
• pp.209-218
• /
• 2000

The purpose of this study was to improve the curriculum for industrial design department in the junior colleges. In order to achieve the purpose, two methodologies were carried out. First is job analysis of the industrial designers who have worked in the small & medium manufacturing companies, second is survey for the opinions of professors in the junior colleges. Some results were as follows: 1. The period of junior college for industrial designers is 2 years according to present. But selectively 1 year of advanced course can be established. 2. The practice subjects same as computational formative techniques needed to product development have to be increased. In addition kinds of selection subjects same as foreign language, manufacturing process, new product information and consumer behavior investigation have to be extended. 3. The next subjects need to adjust the title, contents and hours. (1) The need of 3.D related subjects same as computer modeling, computer rendering, 3.D modeling was high. The use of computer is required to design presentation subjects. (2)The need of advertising and sale related subjects same as printing, merchandise, package, typography, photography was low, the need of presentation techniques of new product development was high. (3) The need of field practice, special lecture on practice and reading original texts related subjects was same as at present, but these are not attached importance to form. As the designers feel keenly the necessity of using foreign language, the need of language subject was high.

• Journal of Sinology and China Studies
• /
• v.81
• /
• pp.161-197
• /
• 2019

This paper aims to find out how rhetorical the rhetoric effect is in the speeches of the winners and runners-ups in the final round of the fifth final title. The subjects of this paper are the speeches of the winners and runner-ups who won the 5th and 10th finalist finals of "I Am a Speaker", which aired on Beijing TV on March 6, 2019. These speeches have images as well as texts, so we will look at the rhetorical expressions in the text and the speech and gesture language of the speakers. In addition, photographs presented as background data on stage when the winner and the runner-up each speak will be included in the analysis. In this paper, we will apply the "Rhetorical Sensitivity Scale", which quantifies the ability of persuasion as a methodology, and sets up the evaluation items based on the traditional theory of rhetoric and then analyzes two speeches. The traditional theory of rhetoric can be divided into five areas and three persuasive elements. The five areas include idea, disposition, expression, memory, and action delivery. The three persuasion elements are Ethos, Logos, and Pathos. In order to pursue objectivity as much as possible, this paper will proceed with both text analysis with verbal expression and video analysis with field situations at the time of speech.