• The Journal of Engineering Geology
• /
• v.20 no.2
• /
• pp.155-167
• /
• 2010

In analysis of slope stability, deterministic analysis which yields a factor of safety has been used until recently. However, probability of failure is considered as a more efficient method because it deals with the uncertainty and variability of rock mass. In both methods, a factor of safety or a probability of failure is calculated for a slope although characteristics of rock mass, such as characteristics of joints, weathering degree of rock and so on, are not uniform throughout the slope. In this paper, we divided a model slope into several zones depending on conditions of rock mass and joints, and probabilities of failure in each zone are calculated and compared with that calculated in whole slope. The persistence of joint was also used as a parameter in calculation of probability of failure. A rock slope located in Hongcheon, Gangwondo was selected and the probability of failure using zoning and persistence as parameter was calculated to confirm the applicability of model analysis.

• The Journal of Engineering Geology
• /
• v.25 no.2
• /
• pp.189-199
• /
• 2015

Our country's leading granite weathered soil of the ground slope failures that occur in cutting slope most cases, it does not require in-depth to the shear strength most of the surface layer is affected by weathering (1~2 m) at a shallow depth close to the ground, it is important to identify the reliability. Based on the result obtained in actual field investigation, the field slope type was classified by each type of wedge slope, Infinite slope, finite slope -I and finite slope -II, and the slope stability was examined respectively. In addition, using the numerical analysis results, the relationship between the slope inclination angle and safety factor was analyzed and it tried to offer basic data to which the stability in the field slope was able to be estimated by analyzing the safety factor change of the slope according to the slope type. In this study, classified into four types of natural slope, safety factor estimation method by slope types is proposed through the numerical analysis. However, some limit exists in generalizing in this research because it does not test various case studies. Therefore, the case study of a wide range of various sypes to assess the safety of various types slope can be made, accommodate a wide range of field conditions reasonable risk evaluation criteria may be derived.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.1
• /
• pp.49-59
• /
• 2013

Heavy rainfall intensity may cause shallow slope failures and debris flow by rill erosion and scour on land surface. The paper represents the difference between native soil (weathered soil) and reinforced soil, which is mixed by hardening agent with flyash as main material, for investigating experimental findings of rill erosion and erosion. Results obtained from artificial rainfall simulator show that erosion rate of reinforced soil mixed with hardening agent is reduced by 20% because an amount of eroded soil on slope surface is inversely proportional to the increase of soil strength. For example, rainfall of 45mm (at the elapsed time of 25mins in rainfall intensity of 110mm/hr) triggers rill erosion on native soil surface, but the rill erosion on reinforced soil surface does not even occur at 330mm rainfall (at the elapsed time of 3hrs in rainfall intensity of 110mm/hr). As a result of slope stability analysis, it was found that the construction method for reinforced soil surface would be more economical, easy and fast construction technology than conventional reinforcement method.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03a
• /
• pp.248-267
• /
• 2004

우리나라의 경우, 국토 면적은 제한되어 있고 특히 밀집한 도심지 인근 공사 시에 사면 경사를 결정하는 것은 쉬운 일이 아니다. 또한 주어진 조건 내(부지의 부족, 환경고려 등)에서 이미 결정되어진 사면경사를 어떻게 유지하느냐 하는 것이 사면에 종사하는 기술자들의 임무인 것이다. 지금까지의 사면분화에 대한 접근 이론들이 너무 고전적인 방법에 치우쳐 있는 경향이 없지 않았다. 또한 기술자들의 보수주의적 경향으로 새로운 이론의 접촉을 멀리한 것도 부인할 수 없다.(중략)

• Journal of Korean Society of Forest Science
• /
• v.107 no.4
• /
• pp.385-392
• /
• 2018

The slope stabilization analysis was performed by conducting survey and selecting the representative section in order to improve slope composition and management technology of masonry embankments in the quarry area, The mean slope of the masonry retain wall (A, B, C, D, E, F) was $38.5^{\circ}$, although the steep slope of the lowest slope (A) as $59^{\circ}$. The horizontal distance of the masonry embankments is 66.2 m and the slope height is 48.3 m. However, the inclination of the masonry embankments is relatively steep and visually unstable. The slope stability analysis for the slope stability analysis was taken into account during the drying and saturation. The slope stability analysis during saturation was performed by modeling the fully saturated slope. The strength constants of the ground were divided into two groups. The safety factor for dry period was 1.850 and the safety factor for rainy season was 1.333. The safety rate of dry period and rainy season was above 1.5 and 1.2. However, the weathered granite on the upper part of the masonry embankments at the time of heavy rainfall is considered to have a high risk of slope erosion and collapse. Therefore, it is considered necessary to take measures for stabilization through appropriate maintenance such as drainage installation.

• Tunnel and Underground Space
• /
• v.30 no.1
• /
• pp.98-107
• /
• 2020

In surface mining, it is very important to create a mining area for economical mining. This study examined the contribution of design factors on slope stability with different slope design and blasting conditions. The design factors were the properties of the rock, the slope angle and the bench height, and the blasting conditions were reflected at different explosive weight and distances. The safety factor of slope was calculated by shear strength reduction method through 3D modeling, and the contribution rate of rock slope was 94.8%, which is relatively higher than other design factors, slope angle 0.89%, bench height 0.58%, and blasting It is shown that it affects about 3.73%, and it can be seen that blasting at a close distance can affect the stability of the slope.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.11 no.1
• /
• pp.29-35
• /
• 1993

The vegetation such as grass, shrub, tree has been used to control the erosion and stabilize the slope for a long time. But the effects of vegetation on slope area is usually neglected in traditional stability analyses. There are many errors in slope analyses in thin soil mantles. Therefore the effects of vegetation is an important factor. But it is difficult and complex to represent the vegetation influence quantitatively in stability analysis. In this study, authors choose the landslide region at the Kum sung dong Kum-jung ku Pusan as a model area. Authors analyzed the degree of slope with the aerial photo interpretation and DTM data extracted from the topographic map, and the relationship of D.B.H. (diameter of breast height), height, and age of tree in field investigation data. Finally authors know the fact that landslide take place approximately 10 or 20 years later in arbitrary afforestable area where the degree of slope is 27. The prevention effect must be considered in the control of vegetation.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.157-170
• /
• 1999

A new design technique is presented to stabilize cut slopes in cohesive soils by use of piles. The design method can consider systematically factors such as the gradient and height of slope, the number and position of pile's rows, the interval and stiffness of piles, etc. The design method is established on the basis of the stability analysis of slope with rows of piles. The basic concept applied in the stability analysis is that the soil across the open space between piles can be retained by the arching action of the soil, when a row of piles is installed in soil undergoing lateral movement such as landslides. To obtain the whole stability of slope containing piles, two kinds of analyses for the pile-stability and the slope- stability must be performed simultaneously. An instrumentation system has been installed at a cut slope in cohesive soil, which has been designed according to the presented design process. The behavior of both the piles and the soil across the open space between piles is observed precisely. The result of instrumentation shows that the cut slope has been stabilized by the contribution of stabilizing effect of piles on the slope stability in cohesive soil.

• Tunnel and Underground Space
• /
• v.12 no.2
• /
• pp.83-91
• /
• 2002

Stability analysis of rocky embankment slopes is done by both the limit equilibrium method and the finite difference method. The height or the rocky embankment is approximately 40 m and the side slope is 1 vertical to 1.5 horizontal. The cohesion and internal friction angle of rock debris are assumed zero and 43$^{\circ}$, respectively. For finite difference analysis, strength reduction method is used to calculate the saft factor of the slope. As a result, the safety factor of the slope is discovered to be 1.4 by using either methods. Considering that the design criteria of the safety factor is 1.3, it can be judged that the rock fragments embankment slope is in a stable state.

• Geotechnical Engineering
• /
• v.18 no.4
• /
• pp.14-60
• /
• 2002