• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.1
• /
• pp.95-102
• /
• 2007

It needs to Prevent damage as aging shotcrete itself exists as a dangerous component to comuting vehicles or infrastructure due to scaling, spaling, and loosening. However, it is hard to make an approach owing to a steep slope and high work, and there has been indicated a limit that it is difficult to grasp the internal condition of shotcrete on the surface. This study aimed to research internal defects that cannot be observed from the surface, by measuring a subtle thermal transfer on the shotcrete surface by using infrared thermography for overcoming such a technical limit. As a result of conducting an inspection through an analysis on measured data and fieldwork using an endoscope camera, it was impossible to accurately determine the wet part because of an excessive coating of shotcrete, yet, This study is proposed effictively extract a void part of the inside with non-destructive and non-touching method.

• The Journal of Korean Society for Radiation Therapy
• /
• v.21 no.1
• /
• pp.17-23
• /
• 2009

Purpose: In treating head and neck cancer, it is very important to irradiate uniform dose on the junction of the bilateral irradiation field of the upper head and neck and the anterior irradiation field of the lower neck. In order to improve dose distribution on the junction, this study attempted to correct non uniform dose resulting from under dose and over dose using the field-in-field technique in treating the anterior irradiation field of the lower neck and to apply the technique to the treatment of head and neck cancer through comparison with conventional treatment. Materials and Methods: In order to examine dose difference between the entry point and the exit point where beam diffusion happens in bilateral irradiation on the upper head and neck, we used an anthropomorphic phantom. Computer Tomography was applied to the anthropomorphic phantom, the dose of interest points was compared in radiation treatment planning, and it was corrected by calculating the dose ratio at the junction of the lower neck. Dose distribution on the junction of the irradiated field was determined by placing low-sensitivity film on the junction of the lower neck and measuring dose distribution on the conventional bilateral irradiation of the upper head and neck and on the anterior irradiation of the lower neck. In addition, using the field-in-field technique, which takes into account beam diffusion resulting from the bilateral irradiation of the upper head and neck, we measured difference in dose distribution on the junction in the anterior irradiation of the lower neck. In order to examine the dose at interest points on the junction, we compared and analyzed the change of dose at the interest points on the anthropomorphic phantom using a thermoluminescence dosimeter. Results: In case of dose sum with the bilateral irradiation of the upper head and neck when the field-in-field technique is applied to the junction of the lower neck in radiation treatment planning, The dose of under dose areas increased by 4.7~8.65%. The dose of over dose areas also decreased by 2.75~10.45%. Moreover, in the measurement using low-sensitivity film, the dose of under dose areas increased by 11.3%, and that of over dose areas decreased by 5.3%. In the measurement of interest point dose using a thermoluminescence dosimeter, the application of the field-in-field technique corrected under dose by minimum 7.5% and maximum 17.6%. Thus, with the technique, we could improve non.uniform dose distribution. Conclusion: By applying the field-in-field technique, which takes into account beam divergence in radiation treatment planning, we could reduce cold spots and hot spots through the correction of dose on the junction and, in particular, we could correct under dose at the entry point resulting from beam divergence. This study suggests that the clinical application of the field-in-field technique may reduce the risk of lymph node metastasis caused by under dose on the cervical lymph node.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.2
• /
• pp.110-119
• /
• 2016

Purpose: This study is aimed to assess changes of stress distribution dependent on different connection lengths and placement of the fixture top relative to the ridge crest. Materials and methods: The internal-conical connection implant which has a hexagonal anti-rotation index was used for FEM analysis on stress distribution in accordance with connection length of fixture-abutment. Different connection lengths of 2.5 mm, 3.5 mm, and 4.5 mm were designed respectively with the top of the fixture flush with residual ridge crest level, or 2 mm above. Therefore, a total of 6 models were made for the FEM analysis. The load was 170 N and 30-degree tilted. Results: In all cases, the maximum von Mises stress was located adjacent to the top portion of the fixture and ridge crest in the bone. The longer the connection length was, the lower the maximum von Mises stress was in the fixture, abutment, screw and bone. The reduction rate of the maximum von Mises stress depending on increased connection length was greater in the case of the fixture top at 2 mm above the ridge crest versus flush with the ridge crest. Conclusion: It was found that the longer the connection length, the lower the maximum von Mises stress appears. Furthermore, it will help prevent mechanical or biological complications of implants.

• The Journal of Korean Academy of Prosthodontics
• /
• v.52 no.3
• /
• pp.246-251
• /
• 2014

In case of prosthesis fabrication by CAD/CAM, location, area and contour of occlusal contacts can be adjusted so more functional occlusion can be acquired. Also, errors in a manufacturing process is reduced compared to cast metal prostheses and porcelain fused metal prostheses fabricated by conventional methods such as casting and porcelain build up. Therefore, prostheses by CAD/CAM show superior occlusion accuracy. Recently, virtual articulator function has been introduced to CAD/CAM system, which reproduces mandibular movement against maxilla. Thus, it is possible to consider occlusal interference in anterior/lateral movement as well as closing movement. There have been many studies on the marginal and internal fit of prostheses using zirconia but the occlusal fit of zirconia crown fabricated by CAD/CAM has not been researched as much. In this case report, 7 zirconia crowns were designed and fabricated by CAD/CAM for total 5 patients. The models of zirconia crowns before and after occlusal adjustment during intraoral try-in were scanned for occlusal contacts, which were compared to evaluate accuracy of prostheses and understand patterns of occlusal adjustment. Most of the occlusal adjustments were done on functional cusps and slopes of zirconia crown, and the magnitude of occlusal adjustment ranged from $15{\mu}m$ to $60{\mu}m$. In the zirconia crown fabricated with CAD/CAM systems, the occlusal adjustment is a necessary procedure, so additional procedures will be needed for compensating reduced mechanical properties.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.534-548
• /
• 2021

In this paper, the feasibility of generating solar power near an abandoned quarry is examined with the objectives of resolving the essential problems that quarries encounter, such as rockfalls and space usage issues. On an abandoned quarry site in Sadang, Seoul, Republic of Korea, two different PV installation methods were analyzed. The first is attaching PV directly on the quarry slope. Since there are no corresponding safety standards and precedents for installing solar panels directly on slopes, the power generation potential was calculated by using topographic data and reasonable assumptions. The surface area of cut slope section was extracted from the Digital Elevation Model(DEM) via ArcGIS and Python programming to calculate the tilt and power capacity of installable panels. The other approach is installing PV as a rockfall barrier, and the power generation potential was analyzed with the assumption that the panel is installed in the direction of facing solar irradiation. For the derivation of power generation, the renewable energy generation analysis program SAM(System Advisor Model) was used for both methods. According to the result, quarries that have terminated resource extraction and remain devastated have the potential to be transformed into renewable energy generation sites.

• Radiation Oncology Journal
• /
• v.16 no.3
• /
• pp.337-345
• /
• 1998

Purpose : To obtain the uniform dose at limited depth to entire surface of the body, the dose characteristics of degraded electron beam of the large target-skin distance and the dose distribution of the six-dual electron fields were investigated Materials and Method : The experimental dose distributions included the depth dose curve, spatial dose and attenuated electron beam were determined with 300 cm of target-skin distance (TSD) and full collimator size (35*35 $cm^2$ on TSD 100 cm) in 4 MeV electron beam energy. Actual collimated field size of 105 cm * 105 cm at the distance of 300 cm could include entire hemibody. A patient was standing on step board with hands up and holding the pole to stabilize his/her positions for the six-dual fields technique. As a scatter-degrader, 0.5 cm of acrylic plate was inserted at 20 cm from the body surface on the electron beam path to induce ray scattering and to increase the skin dose. Results : The full width at half maximum(FWHM) of dose profile was 130 cm in large field of 105*105 $cm^2$ The width of $100\pm10\%$ of the resultant dose from two adjacent fields which were separated at 25 cm from field edge for obtaining the dose unifomity was extended to 186 cm. The depth of maximum dose lies at 5 mm and the 80$\%$ depth dose lies between 7 and 8 mm for the degraded electron beam by using the 0.5 cm thickness of acrylic absorber. Total skin electron beam irradiation (TSEBI) was carried out using the six dual fields has been developed at Stanford University. The dose distribution in TSEBI showed relatively uniform around the flat region of skin except the protruding and deeply curvatured portion of the body, which showed excess of dose at the former and less dose at the latter. Conclusion : The percent depth dose, profile curves and superimposed dose distribution were investigated using the degraded electron beam through the beam absorber. The dose distribution obtained by experiments of TSEBI showed within$\pm10\%$ difference except the protruding area of skin which needs a shield and deeply curvatured region of skin which needs boosting dose.

• Journal of Korean Society of Forest Science
• /
• v.95 no.1
• /
• pp.91-101
• /
• 2006

This study was conducted to analyze the relationships between distributions of major hardwood species and characteristics of topography in natural hardwood forest at Mt. Joongwang, Pyongchang-gun, Gangwon-do which belongs to mid-northern part of the temperate forest. Acer pictum var. mono, Acer manshuricum and Quercus mongolica were affected by elevation, while Ulmus davidiana var. japonica and Fraxinus rhynchophylla were affected by the change of slope. Importance values of A. pictum, Betula costata, Ulmus laciniata and Cornus controversa in valley were 13.41%, 5.68% and 3.29%, respectively, which were higher than in any other topography. Species diversity of valley was the highest with 0.98. Ratio of A. pictum and Q. mongolica in dominant species were 24% and 14%, respectively in valley, while were 19% and 23% in slop. Q. mongolica ratio in ridgeline was higher than any other species. Importance values of A. pictum increased continuously until elevation 1,200 m. importance values of F. rhynchophylla was 6.6% which was the highest value found on elevation 800 m. Distributions of major hardwood species were different according to the elevation. The ratio of Q. mongolica and A. pictum were 6.4%~17.5% and 6.0%~10.7% respectively, which were the highest ratio. Species diversity increased according to the increase of the elevation.

• Progress in Medical Physics
• /
• v.9 no.4
• /
• pp.247-257
• /
• 1998

For effective radiotherapy, it should always be considered that calculation of different dose distribution in heterogenous tissue is important particularly on lung which has low density and large volume. To take precise dose distribution of 6MV X-ray in the thoracic cage, the authors had made a tissue equivalent phantom for thorax, measured dose distribution by thermoluminescent dosimeter and mm dosimeter, and derived methmetical equation coincided with provided theoretical formula. In comparision with isodose curve on case of homogeneous soft tissue, dose of heterogeneous lung tissue had been shown increase about 4% per cm depth on one and multiportal field, less than 15% difference on rotation field for esophagus, and around 20% difference on rotation field for lung according to the degree of rotation angle that must be corrected by dose compensation.

• Journal of Conservation Science
• /
• v.25 no.2
• /
• pp.131-145
• /
• 2009

Goryeong Yangjeondong Petroglyph on the joint face of the bedrock (6m in width, 3m in height) composed of the green sandstone has circles and shield pattern sculptures. The rock is mainly composed of quartz, feldspar, chlorite, illite and calcite with the clay minerals. These clay minerals occur as pore lining, replacement of component and pore fillings. Investigated the weathering aspects including the connection between soluble salt and rock weathering and the stability of the bedrock with petroglyphs. The Major deterioration aspect are grain peel-off, surface exfoliation, cracks and damage. And the bedrock where the joints and cracks advance is interpreted with the fact that has the possibility of the falling rock. For conservation, adhesive need to cover crack and damage and consolidation is necessary in the surface which becomes weak.

• Journal of Life Science
• /
• v.19 no.6
• /
• pp.693-697
• /
• 2009

The purpose of the present investigation was to investigate diversity patterns in Mt. Neungdong forested landscape. It was conducted on twelve sloping plots $(100{\times}100 m)$ in the east and west sides of Mt. Neungdong. A total of 2,157 specimins were identified as trees with a diameter at breast height (DBH) ${\geq}$10 em. There were a total of 135 species of 35 families present in both regions of Mt. Neungdong. Least significant differences (LSD) by post hoc analysis revealed that region A had significantly greater densities than region B. Shannon-Wiener functions differed significantly between forests (F=4.12, < 0.05), with region B forest having a significantly higher value (2.118) than region A (1.882). Pinus thunbergii and Quercus aliena were dominant on most plots of both regions, however, the P. densiflora forest of region A was distributed better in the middle plots exposures compared to the opposite ones. Q. aliena, Q. mongolica, and Carpinus laxiflora largely occupied the middle and lower exposures of region B. The spatial distribution in Neungdong's forest was very heterogeneous and reflected by most species as having micro-climate and patchy distributions.