• The Journal of Engineering Geology
• /
• v.23 no.1
• /
• pp.19-27
• /
• 2013

Deformation of a slope at a coal waste depot and the natural slope under the depot was surveyed and investigated at Dogye village in Samcheock city, Gangwon Province. To investigate the behaviors of the slopes, wire sensors and a rain gauge were installed on the crest of the waste depot slope and inclinometers were installed in the natural slope. The results of deformation monitoring at the crest of the waste depot slope using wire sensors revealed increased deformation with increasing cumulative rainfall. The results of monitoring horizontal deformation of the natural slope revealed that maximum horizontal deformation was also affected by cumulative precipitation. However, the groundwater level at the natural slope showed no change with rainfall. These measurements confirm that deformation at coal mine waste depots is closely related to precipitation, indicating that self-loading at such depots increases with rainfall infiltration, thus causing deformation of the waste depot slope. In addition, increasing the self-load of the coal mine waste depot may cause deformation of the underlying natural slope.

• Journal of the Korean earth science society
• /
• v.31 no.6
• /
• pp.555-562
• /
• 2010

Three-dimensional laser scanner was used to accurately measure any possible strain on a slope under pertaining stress with the time difference of 7 months. The laser scanner has the ability to measure the 3-D coordinate of a target point by calculating the travel time of laser beam between the laser device and the target point, and has been proved to be effective for analysis of the displacement of slopes or large construction. The scanning data measured with time difference were analyzed to find any strain by approaches of plane angle change, curvature variation, twist of frame, displacement of merging point, etc. From the analysis, some weak points showing heavily distorted shape were detected, which was used to design the reinforcement.

• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.181-187
• /
• 2012

Many researches on disaster prevention using computer simulation methods can be performed to minimize the damage of property and to protect human life. Discontinuous deformation analysis (DDA) is a new computer simulation method to analyze the behavior of discontinuous rock masses. Since most rock slope problems are 3-dimensional in nature, 2-dimensional deformation analysis has limited application. In this study, the basic principles of 3-dimensional discontinuous deformation analysis are described. The newly developed 3-dimensional discontinuous deformation analysis method is proposed as the computer simulation method for discontinuous rock masses. Then, the failure behavior of rock slopes are simulated using 3-dimensional discontinuous deformation analysis. The simulation results are compared and examined with the failure behavior at the rock slopes. The results show the applicability of 3-dimensional discontinuous deformation analysis to analyze the deformation and failure mechanisms of rock slopes.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.247-252
• /
• 1994

우리나라 산사태의 대부분은 사면의 깊이가 얕은 상태에서 발생하며, 지형적 지질적 및 강우조건에 따라 각기 다른 사면 파괴의 형태를 보여주고 있다. 본 논문에서는 IFDM의 기법을 이용하여 강우침투에 의해 발생할 수 있는 불포화지반으로의 침윤전선의 진행, 간극수압의 시간적 발생과정 등을 포함하는 침투해석을 수행하였다. 침투해석으로 얻은 강우침투 결과를 hyperbolic 응력, 변형을 모델에 조합하여 시간별로 응력, 변형해석을 할 수 있는 모델을 제안하였다. 이 모델에 의한 해석예로써 용인군 창리 산사태 지역을 선택하여 기존의 한계평형법과 본 논문에서 제안한 모델의 결과를 비교하였다.

• 한국지형공간정보학회:학술대회논문집
• /
• 2004.10a
• /
• pp.155-160
• /
• 2004

근거리 디지털 영상을 이용하여 도로 사면의 3차원 변형을 효율적으로 측정하고자 하였다. 광속조정법(bundle adjustment)에 근거한 사진삼각측량 방법을 적용함에 있어서 종래의 표준적인 기법과 Free-net 기법으로 각각 처리하여 사면의 약 1/35000의 정확도로 3차원 측정과 변형량을 도출하였으며, 토털스테이션에 의해 측정한 결과와 비교하였다. 연구를 통하여 Free-net 기법을 적용함으로써 복잡한 산업현장에서 기존의 측지학적 기준점측량을 행하지 않고도 신속하고 정확한 측정을 기대할 수 있음을 확인할 수 있었다.

• The Journal of Engineering Geology
• /
• v.10 no.1
• /
• pp.1-12
• /
• 2000

Heaving of road and subsidence of slope took place at the Wiri region of the local highway 999 in Gyeongsangbukdo, Korea after heavy rain in the next year of construction. Although the state government had performed remedial treatments by reducing the angle and the height of the slope, deformation had never stopped. Therefore, we have preformed the analysis of deformation and stabilityof the slope. Study area consists of the Cretaceous shale, siltstone and sandstone and two faults are found. The major deformation occurred by sliding of rock mass along faults after heavy rain because not only thepore pressure at the fault plane and the unit weight of sliding mass increased, but did the shearstrength of saturated fault clay become very low. The decrease in shear strength of saturated fault clayis the major factor among the reasons for deformation. Numerical simulations using limit equilibriummodel, finite difference model and finite element model were performed for eight cross sections.Although safety factors are above 1.7 during the dry season, they become below 1.0 when groundwaterlevel raises to surface. The maximum displacement is about 15-3Ocm. However, safety factors increasedto above 2.4 and the maximum displacement is below 2.08cm after remedial treatment, Indicating thatthe slope becomes stable.

• Proceedings of the Korea Contents Association Conference
• /
• 2004.05a
• /
• pp.151-160
• /
• 2004

This research addresses the experimental application of the digital close-range photogrammetric technique for 3D deformation measurement and visualization of road slope. The 3D displacements were extracted by the photo-triangulation based on the bundle adjustment method using the digital imagery. In addition, we produced the digital elevation models, the digital orthorectified images and the 3D perspective view images of the slope employing a digital photogrammetric workstation. Also the inclination map of the slope was generated as the data for monitoring and managing dangerous slopes.

• Tunnel and Underground Space
• /
• v.20 no.2
• /
• pp.105-111
• /
• 2010

This study is to consider applicability of spiral bolt strain gauge as an instrument measuring behavior of soft ground foundation and rock slope. When the instrument was installed on the ground, it can be useful to identify the state of ground behavior because it has the characteristics of flexibility, as well as to apply the ground reinforcement because it has higher pull-out resistance to the ground. From the measurement of behavior to soft ground foundation, the strain shows a stable state in the beginning, then was observed significant change in the upper and the middle of spiral bolt strain gauge after 400 days. This is analyzed that ground loosening, which is due to occurred frequent earthquake of magnitude 1~2 with increased rainfall, lead to the instability of the ground. From the measurement of behavior to rock slope, the strain shows a stable state with very little change in a period of 0~50 days and the biggest strain at 4.2 m (P6) in a period of 50~100 days, then other places except P6 was maintained at a stable state in a period of 100~160 days. The reason is analyzed because that blasting for excavated limestone surrounding was affected to the largest at P6. However, based on the size of strain change by behavior of the soft ground foundation and rock slope, it is considered that the present condition are not effected on stability of retaining structure and rock slope. In conclusion, the proposed spiral bolt strain gauge can be useful to measure behavior of soft ground foundation and rock slope, and also to be measured behavior as well as reinforcement of the target ground.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.2
• /
• pp.19-27
• /
• 2007

In this study, the centrifugal tests were performed with varying the angle of slope such as 1:3, 1:2.5, and 1:2 in order to analyze the deformation and failure type of dredged clay slope for a short term. The displacement mode, displacement vector and the variation of pore pressure with the different slope angle were measured. As a results, even though the displacement in the slope after 4 months were developed in the case of 1:3 for the dredged slope, there are little problems to obtain the stability of dredged slope because the original construction section maintains. Also, in the case of 1:2.5 after 4 months the local slope failure occurred and in the case of 1:2 after 2 months the circle failure starting from the point of the tensile crack occurred. After reviewing the results, the maximum vertical displacement occurred at the crest of slope and maximum horizontal displacement was about double of maximum vertical displacement.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.55-62
• /
• 2000

심층혼합처리공법에 의해 개량된 연약지반상에 사석제를 축조한 후 배면매립을 실시할 경우 사석호안의 변형거동을 관찰하기 위해 계측을 실시하였다. 개량지반상에 사석호안을 축조하기 위한 설계기준을 마련하기 위하여 유한요소법을 이용한 지반변형해석과 Bishop의 간편법을 이용한 사면안정해석을 실시하였다. 이들 해석을 사석제부, 연약지반부 그리고 뒷채음성토부의 토질조건 및 형상이 다른 여러 경우에 대하여 실시하여 그 결과를 서로 비교 분석하였다. 즉, 해석결과를 이용하여 사석제 정사부에서의 수평변위량과 침하？을 호안의 사면안정률과 연과지어 검토하였다. 본 연두결과 사석호안의 사면안전률 1.3보다 낮을 경우 상당히 큰 지반변형이 발생하는 것으로 나타났다.