• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.149-155
• /
• 2013

In this study, factors that affect the air entrainment within a closed conduit by air drawn in through an air vent are investigated using a hydraulic scale model, which represents a gated circular conduit system connected to the intake tower of an irrigation reservoir. In addition, using data obtained during the hydraulic experiments, experimental equations are developed to estimate the amount of air drawn in through the air vent. In case of pressurized flow conditions downstream of hydraulic jumps, the relationships between $\frac{Q_a}{Q_w}$ and $Fr_g-1$ of the data form a experimental equation, $\frac{Q_a}{Q_w}=0.0304(Fr_g-1)^{1.0622}$; in case of free surface flow conditions, $\frac{Q_a}{Q_w}=0.0271(Fr_g-1)^{1.8205}$. Comparing two data sets observed under the two flow regimes with the results of previous researchers, patterns of the data sets are similar to the results estimated using the equations presented previously, and this indicates that the quality of the data obtained during the hydraulic experiments is ensured. In addition, it is revealed that air entrainment phenomena in the regions close to air vents are affected by the characteristics of supercritical flows downstream of gates. Finally, it is concluded that the equation developed for pressurized flow conditions can be applied to design of air vents.

• Journal of Korea Water Resources Association
• /
• v.50 no.1
• /
• pp.55-64
• /
• 2017

This study presents a numerical model for simulating turbidity currents using the ULTIMATE scheme. For this, the layer-averaged model is used. The model is applied to laboratory experiments, where the flume is composed of sloping and flat parts, and the characteristics of propagating turbidity currents are investigated. Due to the universal limiter of the ULTIMATE scheme, the frontal part of the turbidity currents at a sharp gradient without numerical oscillations is computed. Simulated turbidity currents propagate super-critically to the end of the flume, and internal hydraulic jumps occur at the break-in-slope after being affected by the downstream boundary. It is found that the hydraulic jumps are computed without numerical oscillations if Courant number is less than 1. In addition, factors that affect propagation velocity of turbidity currents is studied. The particle size less than $9{\mu}m$ does not affect propagation velocity but the buoyancy flux affects clearly. Finally, it is found that the numerical model computes the bed elevation change due to turbidity currents properly. Specifically, a discontinuity in the bed elevation, arisen from the hydraulic jumps and resulting difference in sediment entrainment, is observed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.18 no.4
• /
• pp.329-337
• /
• 2006

A small hydro-power plant operated by cooling water discharged from the power plant is under construction. In this study, the flow characteristics of the effluent channel and the outfall coastal zone in which the facilities are constructed have been measured and analysed. The flow pattern is highly dependent on the effluent discharge and clearly classified as these typical areas; the upstream and downstream areas of the weir, and the outfall coastal zone. The discharge and the width of the channel in the upstream area of the weir are increased step by step, so the water level fluctuation is small. The flow overtopping the weir is rapidly changing and has highly vertical fluctuation patterns after hydraulic jump just below the weir. The flow pattern in the outfall zone is directed toward the seaward direction and the velocity is dominated by the tidal level fluctuation. The mean tidal range in this area is about 10% greater than that of the Tongyeong tidal gauging station and the wave effects are negligible because of the sheltering effects of this area.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1737-1740
• /
• 2006

본 연구에서는 1차원 수치모형을 이용하여 댐 여수로에서 발생하는 흐름을 해석하였다. 본 연구에서 사용한 1차원 수치모형은 매우 복잡한 지형에 적용이 가능하며, 상류가 사류가 동시에 발생하거나 도수가 발생하는 흐름도 해석할 수 있는 모형이다. 이 모형은 해석해를 가지는 도수의 경우에 적용하여 검증된 바 있으며, 자연하천의 보에서 발생하는 불연속 흐름에 대해서도 적용된 바 있다. 또한 매우 불규칙한 자연하천에서 발생하는 흐름도 효과적으로 모의할 수 있다. 본 연구에서는 댐 여수로 흐름 해석을 평가하기 위해 단순화된 하도에서 발생하는 불연속 흐름에 대해 이론적인 해와 비교하였다. 또한 댐 수리모형 결과에 수치모형을 적용하여 빈도별로 발생하는 흐름을 해석하였다. 해석결과 여수로에서 발생하는 매우 작은 수심을 정확하게 모의하였으며, 여수로 직하류부에서 발생하는 도수의 발생위치, 발생 전후의 수위도 잘 모의하는 것으로 나타났다. 또한 여수로 및 도수 전후에 발생하는 유속도 정확하게 모의하는 것으로 나타났다. 또한 본 연구에서는 1차원 수치모형을 여수로 뿐만아니라 댐 상류 하천, 저수부, 여수로 접근수로, 여수로, 도수, 하류하천등으로 구성되는 전 구간의 흐름을 동시에 모의하기 적용하였다. 적용 결과 댐 저수지 상류 하천과 저수지, 저수지와 접근수로, 접근 수로와 여수로, 여수로와 도수, 도수 발생 후와 하류하천 등에서 복잡하게 형성되는 흐름을 동시에 잘 모의하는 것으로 나타났다. 본 연구에서 사용한 1차원 수치모형을 이용하면 댐 여수로나 저수지, 연계되어 있는 상하류 하천에서의 흐름을 동시에 해석할 수 있기 때문에 향후 수리모형실험과 연계하여 댐 설계에 효율적으로 사용될 수 있을 것으로 전망된다.지는 것으로 평가되었다. 그러나 본 연구결과를 통하여 투수성 포장과 지하수에 관련된 매개변수의 집적과 분석결과는 현장기술 적용 시 매개변수의 유용한 선택과 도시유역의 물 순환 건전화 대안기술 적용에 효과적인 방법론을 제시할 수 있을 것으로 사료된다.첨두홍수량을 저류하기 위해서 상대적으로 넓은 저류면적이 필요한 것으로 나타난다. 대등한 수위감소값의 홍수저감효과를 발휘하기 위해서 본 연구에서는 On-Line 저류지 면적은 Off-Line 저류지에 비 두배 이상이 필요한 것으로 보여졌다.들에 관한 정보는 종종 현장관측에서 조차 무시되는 경우가 많다. 이에 본 연구에서는 수질모형의 매개변수 중 특히 수리특성에 관련된 매개변수들이 수질에 미치는 영향을 파악하는 것을 목적으로 하고 있다. 이를 위해 적용된 수질모형은 QualKo를 사용하였으며, 대상 하천은 낙동강 본류 경남구간 시점 부근인 회천 합류 전부터 낙동강 본류 경남구간 종점 부근인 밀양강 합류 전까지의 경남 오염총량관리 기본계획 시 구축된 모형 매개변수를 바탕으로 분석을 수행하였다. 일차오차분석을 이용하여 수리매개변수와 수질매개변수의 수질항목별 상대적 기여도를 파악해 본 결과, 수리매개변수는 DO, BOD, 유기질소, 유기인 모든 항목에 일정 정도의 상대적 기여도를 가지고 있는 것을 알 수 있었다. 이로부터 수질 모형의 적용 시 수리 매개변수 또한 수질 매개변수의 추정 시와 같이 보다 세심한 주의를 기울여 추정할 필요가 있을 것으로 판단된다.변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략을 활용하는 경우 주식투자기간

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.7
• /
• pp.1173-1182
• /
• 2000

The rapid mixing process has been considered as an important step in water treatment. Since the coagulant dispersion into raw water by rapid mixer can influence on the flocculation and filtration efficiency, many researchers have developed various devices and mixing methodologies. Until now, they focused attention on only coagulant dose, pH. rotating velocity and G value but overlooked the real turbulent flow and mixer geometry in rapid mixer. Therefore this paper questions the significance of turbulent flows in rapid mixer and focuses on the analysis of turbulent fluid in various mixer geometry with CFD(Computational Fluid Dynamics). The results of the jar-tests using various geometries indicate that the turbidity removal rate in a circular jar without baffle is higher than that of a circular with baffle. And the turbidity removal rate in Hudson jar is also founded to be higher than in the circular jar with baffle. The CFD simulation of velocity fields in jar demonstrates that the differences of removal rates among the various geometries are largely due to the formation of the different turbulent fluids fields with different geometries.

• Journal of Korea Water Resources Association
• /
• v.36 no.5
• /
• pp.761-776
• /
• 2003

Numerical models were employed to investigate the hydrodynamics of water flow in the lake behind a dam and the spillway where supercritical flows and negative pressures are likely to occur. In this study, 2-D model, RMA2 was employed to examine the upstream flow pattern and 3-D CFD model, FLUENT was used to evaluate the three-dimensional flow in the approaching region and flow distributions in the spillways and discharge culverts. The bathymetry and the details of structures were carefully taken into consideration in building the models. The results from applying the 2-D model for the planned Hantan River Dam show that large eddies, the velocity of which reaches up to 1 m/s are occurring in several places upstream of the dam. That means that the 2-D numerical model could be utilized to investigate the two-dimensional flow patterns after the construction of a dam. Three-dimensional numerical results show that the approach flow varies depending on stages and discharge conditions, and velocities at spillways, discharge culverts, and sediment flushing tunnels are differently distributed. The velocity distributions obtained from the numerical model and a hydraulic model at the centerline of spillways 100 m upstream of the dam show reasonably similar results. It is expected that 2-D and 3-D numerical models ate useful tools to help optimize the dam design through investigating the flow patterns in the spillway and at the upstream of the dam, which is not always feasible in hydraulic modeling.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.23 no.2
• /
• pp.325-330
• /
• 2009

In Korea, medical diagnostic equipments and biochemical examination can not be used in order for diagnosing sub-healthy state or ante-disease state in oriental medicine clinic. So morphic analogical method used in oriental medicine can be a good tool as a disease-predictable signs in order to enable preventive diagnosis and therapy. Therefore the four geometrical subjects; Essence, Pneuma, Spirit, Blood(四科;精氣紳血) and the four taxonomical species; Pisces, Quadruped, Aves, Carapaces(四類;魚走鳥甲) are chosen as morphic models in this paper. The differences of two classifying methods with four subjects and four species were as follows. The diagnostic category was meta-medical and synthetic against medical specific. The diagnostic object was body in contrast with face. They were able to be applicant in psychology and classification of characteristics against diagnostics and therapeutics directly in oriental medicine. The theoretical basis was basic diagrams of four unit-fluids of body and morphological analogy with four animal species respectively. And the therapeutic aims were systemic pathogenesis following five phase theory against congestion and deficiency of Essence, Pneuma, Spirit, Blood. The four subjects and four species are mixed each other practically in clinic. But it should be used limitedly because of the above reasons described and must divide the principal and secondary factors and follow the pathology of principal shape factor. In order to improve the diagnostic value of ante-disease state, the discriminable standards, measurement methods, limit of interrelating interpretation and the criteria of abnormal disproportion were needed to be defined more clearly in advance.

• Development and Reproduction
• /
• v.2 no.1
• /
• pp.89-99
• /
• 1998

This study was carried out to investigate the morphological changes of gonadotropes in pituitary gland and spermatogenic cells in testis, obtained from 150 of 3-year-old immature and mature male rainbow trout (Oncorhynchus mykiss) during the reproductive cycles from March to February in the following year. In the maturation cycle of the pituitary gonadotropes of cultured rainbow trout, three periods can be distinguished i.e. a period of resting(March-August), a period of full spermatogenesis (September-November), and a period of breeding (December-February). The ultrastructures of the gonadotropes largely parallel the cyclical changes in the tests. The seminiferous tubules contain all spermatogenetic stages and sperm cells in a period of early maturation. At first, the size of the nucleus and cytoplasm decrease gradually at every stages from spermatogonia to spermatids. In the secondary spermatocytes, the small mitochondria are located over the outer cytoplam. In spermatids, the cytoplasmic masses move toward the posterior part of the nucleus. In spermatids, the two large mitochondria are located over the cytoplasm. In spermatids, the cytoplasmic masses move towark the posterior part of the nucleus. In spermatids, the two large mitochondria are located over the cytoplasm and begin to elongate. In spermatozoa, the surface of the nucleus devreases in volume. Examination by TEM shows that the nuclear envelope and plasma membrane are slightlywrinkled and closely adhered to the nucleus of spermatozoa. Two oval mitochondria are quite separated and the flagellum is inserted into the base of the spermatozoa head.The axoneme in this fish has the typical pattern such as nine peripheral doublets and a central doublet(9+2). there are remarkable individual differences in the size and morphology of spermatozoa head as observed by transmission and scanning electron microscopy.

• Parasites, Hosts and Diseases
• /
• v.36 no.2
• /
• pp.81-90
• /
• 1998

The present study was performed to observe the infection status of several kind of animals with indigenous Gnnthostomn in Korea, and morphological characteristics of gnathostome larvae detected from pit-viper, Askistronon breuiccudus, for the species bullfrogs. several kinds of snakes, j.e., 55 Elnphe rufodorsata, 2 Dinodon rufozonatum rufzonatum. 62 Rhnbdophis tisrinus tigrinus and 87 Askistronon app., and 438 cats were examined. A total of 21 larval gnathostomes was detected from 12 pit-vipers, A. breuicnudus. They were 2.233 x 0.343 mm in average size and covered with about 210 transverse rows of minute cuticular spines. Their characteristic head bulbs were provided with 4 rows of hooklets of which average numbers in each row were 36.8, 39.0, 41.7 and 44.3. posteriorly. In the cross sections of midgut level, the intestinal wall consisted of a single layer of 19-25 elongate epithelial cells with a single nucleus. SEM observation of the larvae revealed unique features of head bulb , cuticular spines on transverse striations and a cervical papilla. On the basis of above morphological characteristics, they were identified as the advanced third-stage larvae of Gnothostomo hispinum. It was first confirmed that the pit-viper. ABkistronon breuicaunus is the snake intermediate host of G. hispidun.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1342-1347
• /
• 2007

최근 수자원 분야에서 GIS의 활용은 유역의 수리, 수문분석을 위한 모형의 입력자료 생성 및 모의 결과를 가시화, 이에 따른 유역관리 시스템의 구축 등 폭넓게 활용되고 있다. 또한 국가지리정보시스템에 조사를 통해서 수치지형도 및 주제도를 구축, 구축된 자료의 표준화를 실시하고 있는 실정이다. 그러나 수자원 분야에서 GIS를 활용하기 위한 기술은 주로 선진국을 중심으로 발전하여 왔기 때문에 우리의 실정에 맞지 않아 활용측면에 있어 신뢰할 만한 결과를 얻지 못하고 있는 실정이다. 따라서 국내 상황을 고려하면서 수자원이라는 전문분야 적용에 적합한 GIS(HyGIS)를 개발하고 여기에 수리, 수문분석모형을 연계하여 국내 실무분야에 적용함에 있어 편의성과 실용성을 구비한 모형개발이 이루어져야 한다. 따라서 본 연구에서는 국내 소프트웨어 GeoMania(HyGIS)에 의한 GIS 정보처리의 자동화를 기반으로 하여 실무에서 활용도가 높은 수문모형인 HEC-HMS 및 HEC-1과 수리모형인 HEC-RAS를 연계 및 통합하기 위해서 HyGIS에서 DLL형태로 제공되도록 하였다. HyGIS에서는 수문학적 DEM 분석 및 공간정보 생성, 선형참조가 가능한 하천 네트워크 생성, 유역 시설물 관리 등의 기능을 제공하며 COM(Component Object Model)을 기반으로 개발된 시스템으로 다른 소스로부터 개발된 컴포넌트를 연계하여 시스템의 기능 확장을 손쉽게 수행할 수 있도록 하였을 뿐만 아니라 공간 DB는 GeoMania의 고유 DB인 GSS를 이용한다. HyGIS-HMS는 HyGIS를 통한 국내 유역의 지리정보를 활용하여 HEC-HMS 뿐만 아니라 HEC-1을 추가하여 사용자의 기호와 편의에 따라 모형을 선택할 수 있도록 하였으며 HEC-1의 결과를 가시화하기 위해서 챠트 기능을 추가하였으며 매개변수를 자동으로 산정할 수 있도록 시스템을 구축하였다. HyGIS-RAS는 국내 하천유역에 대해서 기구축 되어있는 하천관리지리정보시스템(RIMGIS)자료를 직접 활용하도록 구성되어있고 자료를 활용하여 제내지와 제외지를 통합하여 TIN분석을 실시하여 범람 홍수해석에 활용할 수 있도록 하였다. 하천수리해석의 기능을 보강하기 위해 역산조도계수 산정모형, 상류-사류 천이류 구간에 대한 부등류 해석모형, 범람 홍수류에 대한 홍수위 산정모형, 하천수리계산시의 불확실도 해석모형 등의 새로운 기능을 추가하여 제시하였다. 모든 입출력자료는 프로젝트 단위별로 운영되어 data의 관리가 손쉽도록 하였으며 결과를 DB에 저장하여 다른 모형에서도 적용할 수 있도록 하였다. 그리고 HyGIS-HMS 및 HyGIS-RAS 모형에서 강우-유출-하도 수리해석-범람해석 등이 일괄되게 하나의 시스템 내에서 구현될 수 있도록 하였다. 따라서 HyGIS와 통합된 수리, 수문모형은 국내 하천 및 유역에 적합한 시스템으로서 향후 HydroInformatics 구현을 염두에 둔 특화된 국내 수자원 분야 소프트웨어의 개발에 기본 토대를 제공할 것으로 판단된다.