• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.11B
• /
• pp.1903-1908
• /
• 2000

사다리형 디지털필터는 일반적으로 IIR 필터의 직접형, 병렬형 또는 종속형과 비교하여 주파수응답 감도가 뛰어나기 때문에 최근 많이 이용되고 있다. 사다리형 디지털필터는 모델의 형식에 따라 연분수 전개가 다르고 주어지는 전달함수에 따라 실현 가능한 형식과 불가능한 형식이 있다. 본 논문에서는 연분수 형태의 제 III 사다리형 디지털필터를 모델로 하여 방형성 결합기와 광섬유를 이용한 사다리형 광섬유필터의 실현조건과 설계방법을 논하였다.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1
• /
• pp.16-24
• /
• 1999

Design of SAW ladder filters has been performed by a rather trial and error method, that is, by modifying the design variables step by step until designed performance of the filter satisfies given specifications. In this work, optimal design method has been developed that automatically determines the detailed pattern of the SAW ladder filter to meet the specification once desired performance is given. As a first step for the development, the analysis tool for the SAW ladder filter has been produced by means of the Smith equivalent circuit analysis technique, and its validity has been verified through comparison of its calculation result with experimental data. With the analysis tool, we have investigated the performance variation of the filter with the change of its design factors, and the result has led to the optimal design algorithm. Validity and efficiency of the algorithm has been checked through test design of several SAW ladder filter samples on the market.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1048-1053
• /
• 2002

In this paper, thin film bulk acoustic resonator(TFBAR) lattice and balanced type filter topologies are designed and fabricated. Aluminium nitride and platinum are used for piezoelectric material and top and bottom electrodes, respectively. Air-gap is placed to avoid silicon substrate loading effect and the performance of these lattice and balanced filters is compared with ladder filters. These filters have selectivity over 15 dB for lattice type and 30 dB for balanced type and reveal wider bandwidth of the ladder filters. For balanced type filters, minor tuning procedure is not needed and they are readily available for RF filter in wireless applications.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.2
• /
• pp.102-109
• /
• 2002

This paper proposes a new design algorithm to optimize the withdrawal weighted SAW ladder devices, Withdrawal weighting on SAW resonators gives enhanced bandwidth and transition band characteristics, so an optimization algorithm was developed for ladder type SAW filters. To illustrate the validity of the technique, this method was applied to the design of RF band CDMA TX SAW filters, and the design results were confirmed to show good agreement with experimental performance.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.51 no.5
• /
• pp.1-12
• /
• 2023

This study evaluated the overturning stability of portable tripod ladders used for high-altitude work such as tree management and pruning work in landscaping construction and management. Portable tripod ladders, which are included in general mobile or portable ladders frequently used in industrial sites, are supported in a triangular support structure, not a 4-point support like common A-type Ladders. In addition, since the working height is more than twice that of a mobile or portable ladder, the possibility of an overturning accident that threatens the safety of workers with a fall accident is high. Therefore, based on the overturning stability test specified in ANSI-ASC A14.7 and EN 131-Part 7, which are related standards for about 130 types of portable tripod ladders sold and used in Korea. An equation to calculate each moment according to working height was derived. Then, each calculated moment was compared to evaluate the safety factor for overturning and stability. As a result of the overturning stability evaluation according to each standard, when the provisions of EN 131-Part 7 were applied, portable tripod ladders with 8 steps in the rear direction and 6 steps or more in the side direction were evaluated as unstable against overturning, but according to ANSI-ASC A14.7 regulations. It was evaluated that the stability against overturning was secured in all directions and number of steps.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.565-571
• /
• 2001

The objective of this study was to investigate the characteristics of air flow and heat transfer caused by trapezoid rods array in impinging air jet system. In this study, trapezoid rods have been set up on front of flat plate to act as a turbulence promoter. Local Nusselt numbers were determined as a function of three parameters: (a) the space from rods to heating surface(C=1, 2, 4mm), (b) the pitch between each rods(P=30, 40, 50mm), (c) the distance from nozzle exit to flat plate(H/B=2, 6, 10). And this research compared the above with the experiment without trapezoid rods. As a result, heat transfer performance was best under the condition of C=1mm and as the pitch is 30mm. In this case, maximum rate of heat transfer augmentation is about 1.9 times greater compared to that without trapezoid rods.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.367-370
• /
• 1999

일반적 인 SAW 필터에서 발생하는 선형성의 한계 및 천이대역의 특성을 개선하기 위한 새로운 구조의 이중구조 사다리형 SAW 필터의 최적 설계 방법을 제시하고 그 가능성을 확인하였다. 이중구조 SAW 필터는 일반적인 사다리형 필터의 구조를 바탕으로 하되, 두 개의 서로 다른 필터가 각각 주어진 대역사양을 반반씩 만족시켜 전체의 필터특성이 구현될 수 있도록 하였다. 특히 고주파 대역에서 만족시키기 어려운 정재파비 및 뛰어난 천이대역 특성을 만족시킬 수 있는 장점을 가지며, 이를 위해 withdrawal 가중기법 및 기판상에 encp화된 마이크로 스티 립라인 인덕터를 이용하였다. 우선 이중 구조 필터구조를 결정한 후, microstrip 라인 인덕터의 위치 및 인덕턴스 변화에 따른 필터특성 변화를 살펴보았으며, 필터의 각종 형상변수의 변화에 따른 필터 특성변화를 조사하였다. 이상의 결과를 바탕으로 새로운 방법의 이중구조 SAW 필터의 설계방법을 제시하였으며 그 타당성을 검증하기 위해 1.8 GHz 대역의 RF 필터에 대한 설계 결과를 나타내었다.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.02a
• /
• pp.92-93
• /
• 2005

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.1-6
• /
• 2005

We have studied the polarization effects and the coupling intensity effects of electromagnetically induced transparency(EIT) in the 5S$_{1}$2-/5P$_{3}$2-/5D$_{5}$2/ ladder system of Rb. We obtained the EIT spectrum with the hyperfine structure of 5D$_{5}$2/ transitions and the minimal width of the measured EIT spectrum was 6.5 MHz. We observed the change of the relative magnitudes of the hyperfine structure of EIT according to not only the polarizations of lasers but also the intensity of the coupling laser. The cause of the coupling intensity effects is that the EIT signal nonlinearly increases to the coupling intensity.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.235-235
• /
• 2018

홍수 시의 산지하천 만곡부는 2차류 발생과 편수위 상승에 따른 하상세굴 및 홍수범람 위험이 크다. 만곡부 외측에 주로 설치되어 있는 콘크리트 옹벽호안은 표면이 매끄러워 홍수피해를 가중 시킨다. 이러한 피해를 저감시키기 위해 콘크리트 옹벽에 돌출줄눈을 설치하여 유속조감 및 설치효과를 분석한 바 있다. 본 연구에서는 기존에 제안된 직사각형 단면의 돌출줄눈보다 내구성을 추구한 사다리꼴 단면의 돌출줄눈을 제시하여 수리모형 실험을 수행하였다. 수리모형 실험은 개수로 직선수로에서 수로경사 0.0035 조건에서 수로 출구 게이트를 조절하면서 이루어졌다. 모형 돌출줄눈의 조도높이는 3cm로 하였으며, 사다리꼴 밑각은 $45^{\circ}$로 완만한 경우이다. 설치간격은 무차원 돌출줄눈 간격을 기준으로 ?형 조도인 6으로 하였다. 돌출줄눈의 설치 유무에 따라 유량에 따른 수위를 측정하고 유속을 산정하여, 마찰저항의 변화를 파악하였다. 공급유량에 따른 Froude 수는 0.168~0.359 범위였으며, 유량이 증가에 따라 Manning의 조도계수는 감소하였다. Froude 수가 0.25보다 큰 경우 돌출줄눈설치의 조도계수가 미설치보다 큰 것으로 파악되었다. 그러나 사다리꼴 돌출줄눈의 흐름저항효과는 직사각형 돌출줄눈에 비해 상대적으로 작았다. 수로 횡단면의 수위분포에 따르면, 돌출줄눈 설치 측벽 주변에서 흐름저항에 따른 유속감소와 수위상승 효과가 나타나는 것으로 파악되었다. 이번 사다리꼴 돌출줄눈은 흐름저항 효과가 크지 않았기 때문에 사다리꼴 밑각을 조정하여 새로운 단면에 대한 추가적인 실험이 필요할 것으로 보인다.