• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.8
• /
• pp.753-760
• /
• 2008

The present study is concerned with aerodynamic characteristics and reference trajectory generation of Hope-X in Approach/Landing phase. To create reference trajectory generation in A/L phase, detailed informations on lift and drag coefficients of Hope-X must be provided. To obtain these informations, aerodynamic characteristics of Hope-X are analyzed using the commercial CFD code, Fluent. The A/L phase is conceptually divided into three sub-phases: the Steepglide Slope phase for stability of vehicle, the Flare Maneuver phase for safety landing, the Circular Flare for smooth connecting with these both phases. The reference trajectory is obtained by determination of flight-path angle through geometrical formulas with consideration of aerodynamic coefficient and dynamic characteristic.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.3
• /
• pp.41-49
• /
• 2009

The present paper describes a mathematical modeling and simulation of the separation of a solid rocket booster from an air breathing engine vehicle. The vehicle and booster are considered as a multi-connected body and the booster is assumed to move only along the axial direction of the vehicle. The dynamic motion of the vehicle and the booster were modeled by using Kane's method. The aerodynamic forces on the whole system along various positions of booster were calculated by using DATCOM software and the internal pressure force acting on the effective surface during separation was simply calculated with gas dynamics and Taylor MacColl equation. Numerical simulation was done by using Mathworks-Matlab. From the result, the variation of Mach number and angle of attack are not large during the separation, so the variation of pitch angle and the characteristics of inlet flow for varying the Mach number and angle of attack during the separation test can be identified as neglectable values.

• Journal of Advanced Navigation Technology
• /
• v.24 no.3
• /
• pp.224-231
• /
• 2020

An optical tracking plays an important role for measurement operation, as it is responsible for low altitude measurements that are difficult to obtain with radar systems. Since the existing optical tracking systems have not been developed in the proving ground itself so far, it is difficult to modify them to fit the environment of the proving ground. Also, they are designed as a vehicle-mounted type, so there is a limitation in selecting an optimal site. The in-house developed small optical tracking system is designed with a simple configuration to overcome these shortcomings and makes it possible for operators to operate the system at any place in the proving ground. In addition, there has been a need of developing small optical trackers by ourselves to be prepared for future research so that artificial intelligence (AI) can be applied to the optical tracking systems. In this paper, we described the design concept of the small optical tracker, the configuration of the components to implement the basic tracking function, and showed the results of the simulation to set the configuration of the equipment according to the characteristics of the flight targets.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.10
• /
• pp.843-852
• /
• 2016

The autorotative flight of maple seeds(Acer palmatum) is numerically simulated based on the 3D geometry and the motion parameters of real seeds. The nominal values of the motion parameters are 1.26 m/s for descent velocity, 133.6 rad/s (1,276 rpm) for spinning rate, $19.4^{\circ}$ for coning angle, and $-1.5^{\circ}$ for pitch angle. A compact leading-edge vortex (LEV) positioned at the inner span of the seed blade causes a large suction pressure on its leeward surface. The suction pressure peaks occur near the leading region of inner span sections. The flow pattern characterized by the prominent LEV and the values of aerodynamic force coefficients obtained in the present study are in good agreement with experimental data measured for a dynamically-scaled robot maple seeds. A spiraling vortex developed in the leeward region advances toward the seed tip and merges with the tip-passing flow, which is considered to be a mechanism of maintaining stable and attached LEV for the autorotating maple seeds.

• Composites Research
• /
• v.27 no.2
• /
• pp.47-51
• /
• 2014

The purpose of the present study is to develop lightweight and simple smart actuators in order to replace conventional hydraulic/pneumatic actuators, and to apply the developed actuators to the actuation systems of a small unmanned air vehicle. This research describes the procedures of design, manufacturing of the piezo-composite actuator, and the performance evaluation. From the test results of the developed devices, we found the possibility of piezo-composite actuator could be used as a control surface of a small UAV system. We have designed and manufactured two kinds of piezo-composite actuators, unimorph actuator and bimorph actuator. The manufactured actuators were evaluated through the performance testes. It was found that the bimorph type actuator showed more linear angle change for the same excitation voltage variation than unimorph type. It is expected that piezo-composite actuator has a possibility to be used not only as a control surface of small unmanned flying vehicle but also as a control surface actuator of a guided missile fin through the miniaturization of power supply and control system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.3
• /
• pp.217-225
• /
• 2013

Typical quadrotor aircraft use four differential thrust vectors to control the motion. In this study, we design a quadrotor aircraft using collective and cyclic control to improve the shortcomings of existing quadrotor aircraft. The quadrotor aircraft with cyclic control can fly at various attitudes due to the excessive control degrees of freedom. Hence the quadrotor aircraft with cyclic control is suitable as high performance aircraft. In this study, modeling and stability analysis of the quadrotor aircraft have been performed using FLIGHTLAB. LQR control systems were designed using linear models at various flight conditions and verified through nonlinear simulations using MATLAB.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.6
• /
• pp.503-508
• /
• 2007

In this study, the aeroelastic response and stability of bearingless rotors are investigated using a large deflection beam theory. The outboard main blade, flexbeam, and torque tube are all assumed to be an elastic beam undergoing arbitrary large displacements and rotations. The finite element equations of motion obtained from Hamilton's principle. Two-dimensional quasi-steady strip theory is used to evaluate aerodynamic forces. In hover, the modal approach method based on coupled rotating natural modes is used for the stability analysis. In forward flight, the nonlinear periodic blade steady response is obtained by integrating the full finite element equation in time through a coupled trim procedure with a vehicle trim. The results of the full finite element analysis using the large deflection beam theory are compared with those of a previously published modal analysis using the moderate deflection-type beam theory.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.83-91
• /
• 2005

This paper describes the structural strength test technique and the results for cylindrical supersonic vehicle subjected to both aerodynamic load and thermal load. The special positioning system using spring links was designed to float, support and restrain the test airframe during the test and the down-time. The hydraulic system and the electric heating system were utilized to apply the aerodynamic load and the thermal load to the test airframe together. Particularly, several hundreds of infrared quartz lamps were used for the heating system, and the thermal test conditions were successfully simulated. The test results showed that this kind of high temperature test is adequate to verify the structure integrity and produce useful engineering data which is necessary for the possible structural modification under thermal environments.

• Journal of Advanced Navigation Technology
• /
• v.20 no.5
• /
• pp.387-393
• /
• 2016

To perform realistic air traffic control (ATC) simulation in various air traffic situations, an aircraft dynamic model that is accurate and efficient is required. In this research, an improved five degree of freedom (5-DOF) dynamic model with feedback control and guidance law is developed, which utilizes selected performance data and operational specifications from the base of aircraft data (BADA) and estimations using aircraft design techniques to improve the simulation fidelity. In addition, takeoff weight is estimated based on the aircraft type and flight plan to improve simulation accuracy. The dynamic model is validated by comparing the simulation results with recorded flight trajectories. An ATC simulation system using this 5-DOF model can be used for various ATC related research.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.1
• /
• pp.49-62
• /
• 2005

The VR (virtual reality) simulator such as helicopter simulation needs virtual environment of existing urban area. But the real urban environment keeps changing. We need a modeling method to make use of the GIS data that are updated periodically. The flight simulation needs to visualize not only buildings in near distance but also a large number of buildings in the far distance. We propose a method for modeling urban environment from aerial image and digital map with a comparatively small manual work. Image based modeling is applied to urban model which considers the characteristic of Korean cities. Buildings in the distance can be presented without creating a lot of polygons. Proposed method consists of the pre-processing stage which prepares the model from the GIS data and the modeling stage which makes the virtual urban environment. The virtual urban environment can be modeled with the simple process which utilizes the height map of buildings.