• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.225-236
• /
• 2014

Shear wave velocity was used to estimate the geotechnical characteristics (void ratio and shear strength) of ground near an underground rainfall storage facility. An oedometer cell was utilized to measure the shear wave velocity and the displacement of specimens. Shear strengths were obtained by direct shear tests. The relationships along the shear wave velocity, void ratio, and shear strength were verified and used to infer the shear strength profile with the depth. In addition, changes in shear strength due to the construction of the underground rainfall storage system were estimated using the suggested method. The results show that the in-situ shear strength deduced from the shear wave velocity-void ratio-shear strength relationship is in good agreement with that obtained from an in-situ investigation (SPT).

• Journal of Korean Society of Transportation
• /
• v.18 no.5
• /
• pp.57-67
• /
• 2000

Two fuzzy travel time estimators for interrupted traffic flow were developed based on field survey data and simulation data 7hat is collected from DETSIM, which is microscopic traffic simulation model that car-following theory is applied. One is FETTOS(Fuzzy Estimator of Travel Time using Occupancy and Spot speed) and the other is FETTOS(Fuzzy Estimator of Travel Speed using Volume and Occupancy). Fuzzy logic controller was applied to the estimators to deal with non-linear relationship between traffic variables and travel time. According to results of simulation and field survey. estimation of travel time can be modeled by using percent occupancy better than any other traffic variables. Detector location from storyline and signal timing Plan of intersection are affected to estimate travel time. With a few findings, the estimator was constructed and its performance was tested for observed travel time data and simulated data. FETTOS which needs signal timing plan and detector location estimates travel time with accurate better than FETSVO does. However. FETSVO has excellent transferability because the estimator needs set of input data only; volume and time mean speed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.4
• /
• pp.91-103
• /
• 2016

The work zone traffic management is of keen interest because the unstable traffic stream in work zones leads to not only less productive traffic operational efficiency but also negative impacts on traffic safety. A promising method to address such issues is variable speed limit systems(VSLS). VSLS is expected to increase in throughput and to enhance safety by diminishing the crash potential. In addition, the usefulness of VSLS has been demonstrated by significant amount of existing literature. The objective of this study is to identify the effectiveness of VSLS based on a meta analysis technique. Throughput and travel speed were used as measures of effectiveness for VSLS in terms of the operational efficiency and safety respectively. Results showed that approximately 16.4% increase in throughput and 16.5% decrease in travel speed were obtainable by VSLS. The outcomes of this study would be useful in developing technologies and polices for better operation of VSLS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.249-249
• /
• 1999

GaN과 같은 III-nitride 반도체 관한 식각 기술의 연구는 blue-emitting laser diode(LD)를 위한 경면(mirror facet)의 형성뿐만아니라 새로운 display 용도의 light emitting diodes (LED), 고온에서 작동되는 광전소자 제조 등에도 그 중요성이 증대되고 있다. 최근에는 III-nitride 물질의 높은 식각속도와 미려하고 수직한 식각형상을 이루기 위하여 ECR(Electron Cyclotron Resonance)이나 ICP(Inductively Coupled Plasma)와 같은 고밀도 플라즈마 식각과 CAIBE(Chemically assisted ion beam etching)를 이용한 연구가 진행되고 있다. 현재 제조되어 지고 있는 LED 및 LD와 같은 광소자의 구조의 대부분은 p-GaN/AlGaN/InGaN(Q.W)/AlGaN/n-GaN 와 같은 여러 층의 형태로 이루어져 있다. 이중 InGaN는 광소자나 전자소자의 특성에 영향을 주는 가장 중요한 부분으로써 현재까지 보고된 식각연구는 undoped GaN에 대부분 집중되고 있고 이에 비해 소자 특성에 핵심을 이루는 InGaN의 식각특성에 관한 연구는 미흡한 상황이다. 본 연구에서는 고밀도 플라즈마원인 ICP 장비를 이용하여 InGaN를 식각하였고, 식각에는 Cl2/CH4, Cl2/Ar 플라즈마를 사용하였다. InGaN의 식각특성에 영향을 미치는 플라즈마의 특성을 관찰하기 위하여 quadrupole mass spectrometry(QMS)와 optical emission spectroscopy(PES)를 사용하였다. 기판 온도는 5$0^{\circ}C$, 공정 압력은 5,Torr에서 30mTorr로 변화시켰고 inductive power는 200~800watt, bias voltage는 0~-200voltage로 변화시켰으며 식각마스크로는 SiO2를 patterning 하여 사용하였다. n-GaN, p-GaN 층 이외에 광소자 제조시 필수적인 InGaN 층을 100% Cl2로 식각한 경우에 InGaN의 식각속도가 GaN에 비해 매우 낮은 식각속도를 보였다. Cl2 gas에 소량의 CH4나 Ar gas를 첨가하는 경우와 공정압력을 감소시키는 경우 식각속도는 증가하였고, Cl2/10%Ar 플라즈마에서 공정 압력을 감소시키는 경우 식각속도는 증가하였고, Cl2/10%CHF3 와 Cl2/10%Ar 플라즈마에서 공정압력을 15mTorr로 감소시키는 경우 InGaN과 GaNrks의 선택적인 식각이 가능하였다. InGaN의 식각속도는 Cl2/Ar 플라즈마의 이온에 의한 Cl2/CHF3(CH4) 플라즈마에서의 CHx radical 형성에 의하여 증가하는 것으로 사료되어 진다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.7
• /
• pp.688-694
• /
• 2008

A rotordynamic analysis is performed for a high thrust class liquid rocket engine turbopump considering the dynamic characteristics of ball bearings and pump noncontact seals. Complex eigenvalue problems are solved to predict the rotating natural frequencies and damping ratios as a function of rotating speeds. Synchronous rotor mass unbalance response and time transient response analyses are also performed to figure out the rotor critical speed and the onset speed of instability. From the numerical analysis, it is found that the rear bearing stiffness is most important parameter for the critical speed and instability because the 1st mode is turbine side shaft bending mode. The pump seal effect on the critical speed is enlarged as the rear bearing stiffness decreases and the front bearing stiffness increases.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.78-86
• /
• 2014

The purpose of this study is the displacement and velocity dependence evaluation of I type and S type metallic dampers. For this purpose, 12 metallic damper specimens are prepared and dependence test are performed. Test variables are strut type, displacement and velocity dependence. From the evaluation results of dependence tests, number of cycles are fully exceeded than minimum 5 cycles described in ASCE 7-10. According to displacement dependence test results, larger target displacement (50mm) shows lower cyclic numbers and cumulated energy dissipated area than lower target displacement (25mm). Also it show higher strength and early failure than short target displacement. In velocity dependence evaluation, fast target velocity (60mm/sec) shows lower cyclic numbers and cumulated energy dissipated area than target velocity (40mm/sec). As a results of basic properties, dependence evaluation and cumulated energy dissipated area evaluation, dependence capacity of S type metallic damper is far superior than I type.

• Microbiology and Biotechnology Letters
• /
• v.20 no.5
• /
• pp.588-596
• /
• 1992

The fermentation characteristics of ethanol production by the use of immobilized Zymomonas mobilis KCTC 1534 cells were investigated in terms of formation factors such as substrate and product concentration. In batch fermentation, the maximum values of specific ethanol productivity, specific substrate uptake rate, ethanol yield, and glucose conversion rate were $29.14g/{\ell}{\cdot}h$, $60.24g/{\ell}{\cdot}h$, 0.48g/g, and 98.4%, respectively, with 17% glucose medium, and its ethanol productivity was $2.91g/{\ell}{\cdot}h$ in the case of 25 hour fermentation time. Repeated batch fermentation was possible for 30 days with 2.24-$2.94g/{\ell}{\cdot}h$ ethanol productivity. In semicontinuous fermentation, the maximum ethanol productivity was shown to be $15.7g/{\ell}{\cdot}h$ at $0.36h^{-1}$ effective dilution rate with 17% glucose concentration. In this case, ethanol yield coefficient and glucose conversion rate were 0.39 g/g, 64.7%, respectively.

• KSBB Journal
• /
• v.9 no.5
• /
• pp.443-449
• /
• 1994

Fermentation characteristics of Kluyveromyces fragilis CBS 1555 with Jerusalem artichoke juice, in extractive ethanol fermentation in aqueous two phase systems composed of polyethylene glycol 20000 (PEG) and crude dextran(Dx), were investigated as a function of initial sugar concentrations, concentrations of ethanol formed, or fermentation time. Both specific ethanol production rate increased with decrease in concentrations of PEG and Dx in two-phase systems. Without being related to the compositions of aqueous two-phase system, maximum specific cell growth rate and maximum specific ethanol production rate were showed in the initial sugar concentration fo $80g/\ell$ and $120g/\ell$, respectively. The inhibition effects of ethanol on specific cell growth rate and specific ethanol production rate decreased with decrease in PEG concentration and in the range of 2.5 to 5% Dx. Specific cell growth rate and specific ethanol production rate was fitted as an exponential function and a hyperbolic function, respectively, of the concentrations of ethanol formed. Overall ethanol productivity increased with increase in initial sugar concentrations, and also the required time for the maximum productivity was so. Ethanol production rate by the elapsed fermentation time showed the maximum value in the initial sugar concentration of $160g/\ell$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.27-35
• /
• 1998

In this paper, we propose a novel spectral-chopping model of Class-II$(1+D)^2$ -PRS system which reveals improved spectral efficiency. We build up the model having spectrum chopped by the amount of Nyquist over-rate, and then compare its characteristics with the conventional model in both the time-domain and the frequency-domain. When the transmission system operates above the Nyquist rate, the new model has better performance than the conventional PRS using its inherent speed-tolerance. According to our investigations, Class-II PRS shows more excellent effect in the spectral-chopping method than Class- I and W types analyzed previously. We ascertain that the over-rate of 26.675 obtained by the inherent speed-tolerance could be improved upto 40% using spectrum-truncation. These effects come from the fact that the raised-cosine spectrum of Class-II PRS has smaller Boss of frequency component and energy than any other types for the same amount of truncation. In order to validate these theoretical results, we present their sidelobe-trends confirming cancellation effects at the sampling instants and some experimental results showing their patterns of eye-openings and spectra.

• Clean Technology
• /
• v.15 no.4
• /
• pp.245-252
• /
• 2009

Profiles development of melt spinning process of poly(lactic acid) (PLA) was simulated via a numerical method and the radial temperature distribution was calculated using finite difference method. The spinning speed ranged from 1 km/min to 5 km/min was analyzed and the effect of spinning conditions on the radial temperature distribution was investigated. At low spinning speed, the difference between PLA and poly(ethylene terephthalate) (PET) was relatively small. As the spinning speed increased, the difference in velocity profile became prominent. PLA showed a slower spinning speed than PET and solidified more slowly. The temperature difference between the core and surface of the PLA filament reached 4.6 K, which was less than that of PET filament with a difference of 10.4 K. The radial temperature difference increased with increasing the cooling-air velocity and the spinning temperature.