• Journal of KIBIM
• /
• v.6 no.2
• /
• pp.12-18
• /
• 2016

The entire construction safety is significantly influenced by proper uses of temporary structures. However, in current practices, temporary structures are used without sufficient planning and analysis on their impact on safety. Consequently, problems in worker safety and loss of productivity are frequently caused related to temporary structures. This paper introduces an approach that uses Building Information Modeling (BIM) to automatically create temporary structures as part of construction plans and identifies potential safety hazards related to the temporary structures. In this study, the type of temporary structure is limited to scaffolding. Automation algorithms were developed and applied to (1) analyze daily construction site conditions (2) create required scaffolding objects, and (3) identify potential safety hazards related to scaffolding. A case study using a real-world construction project demonstrated that scaffolding objects were properly created based on user-input and potential safety hazards were successfully identified without human intervention.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.94-100
• /
• 2021

To improve the productivity of cargo containment construction for a membrane LNG carrier, it is important to shorten the installation period and process of the scaffolding system, which is a construction workbench of a cargo containment for a membrane LNG carrier. As an effective method, opinions are being gathered to enlarge the lifting unit from the existing two stages to eight stages. On the other hand, the stresses around the pin and hole will increase significantly because of the increase in lifting load according to the large size of the module. The purpose of this study was to establish a new large module-lifting plan by introducing TRIZ to solve these problems. This study adopted a method to utilize 40 inventive principles, which is one of the various problem-solving tools of TRIZ. First, technical contradictions were derived, the engineering parameters were selected. Second, efficient inventive principles were selected to overcome the technical contradictions using a contradiction matrix. Finally, the general and specific solutions were derived through the selected inventive principle, and structural analysis confirmed that the stress generated in the structure was low. The utility of TRIZ was confirmed by the successful lifting of large modules using the established lifting method.

• Applied Chemistry for Engineering
• /
• v.27 no.2
• /
• pp.217-220
• /
• 2016

Phytoestrogens are one of quasi-estrogens which are not generated within the endocrine system, but consumed by intaking phytoestrogenic plants. Phytoestrogens, also called as "dietary estrogens", are various botanic chemical compound groups naturally occurring nonsteroidal plant compounds of spontaneous generation. Due to their structural similarities to estrogone, they may provide desirable health benefits for reducing the menopausal symptoms. In this paper, various phytoestrogens were extracted from sophora root, pomegranate and kudzu by ultrasonic extraction process. In this study, the amount of extracted phytoestrogens at various ultrasonic power strengths and extraction times were compared, which could be used as basic data in the study of biology and chemistry related to natural products.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.1
• /
• pp.25-32
• /
• 2016

The purpose of this study is to evaluate the performance on the compressive bonding shear strength of ultra-high strength steel fiber reinforced cementitous composites(UHSCC). As a result of compressive bonding shear strength through Direct shear test, It was found that the specimen($150{\times}150{\times}150mm$) of NC(Normal concrete) + NC showed similar compressive bonding shear strength at whole experimental level. On the other hand, the specimen of UHSCC + UHSCC showed decrease of compressive bonding shear strength from after 30 minutes of the retarded placement than 0 minute. As a result of analyzing failure mode of bonding interface, It was found that the specimen of NC + NC showed mixed failure at whole experimental level. In case of the specimen of UHSCC + UHSCC, it showed interface failure from the specimen that are 30 minutes, 60 minutes and 90 minutes of delay of concrete placing. As a result of analyzing XRD test in terms of the placement interface on the specimen of NC and UHSCC, relatively much amount of $SiO_2$ was detected from the specimen of UHSCC than that of NC. It is judged that the most of main components of coating film shown in the specimen of UHSCC is $SiO_2$. In conclusion, it is judged that UHSCC which is made from after 30 minutes of delay of concrete placing is unable to be used as structural member because of deterioration of bonding performance. From later study, it is judged that the improvement of bonding performance from the part of cold joint occurrence is necessary through the interface preparation method.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.92-101
• /
• 2020

It is necessary to develop a rational method for evaluating the safety of bridges for the passage of inseparable crane vehicles exceeding the limit weight. In this study, the same method applied to the development of the recently introduced reliability-based highway bridge design code - limit state design method is applied to the calibration of the live load factor for the crane vehicle. Structural analysis was performed on the concrete bridge and the required strengths of the previous design code, the current design code and AASHTO LRFD were compared. When comparing the unfactored live load effect, the live load of the crane was greater than that of the current and previous design code. When comparing the required strength by applying the calibrated live load factor, the previous design code demands the largest strength and the current design code and the crane live load effect yields similar value. The results of safety evaluation of the actual bridges on the candidate route for the crane passage secured the same reliability as the target reliability index required by the design code and the strength of the cross section of the actual bridge is calculated greater than the required strength for the passage of the crane, which confirms the safety for the passage of the crane.

• The Journal of the Korea Contents Association
• /
• v.19 no.5
• /
• pp.64-73
• /
• 2019

This study analyzed the efficiency by using the DEA model to evaluate the competitiveness of specialty construction firms. The target of the analysis is 300 firms with continuous data from 2010 to 2017 as listed and externally listed firms. Significant analysis results are as follows. First, the efficiency of specialty construction firms is lower than that of general construction industry. Second, efficiency by type was highest in facilities construction and dismantling work. This shows that the relevant industries such as reinforced concrete works and scaffolding and demolition work are relatively efficient in specialty construction industry. Third, the efficiency of specialty construction industry is affected by economic fluctuations. When the construction industry is in the expansion phase, the efficiency value is high and the efficiency value is low in the down phase. Finally, in the scale profitability analysis, specialty construction industry was most analyzed by DRS. This means that it is effective to scale down for the efficiency of the firm.

• Applied Chemistry for Engineering
• /
• v.26 no.3
• /
• pp.311-318
• /
• 2015

This work investigated the plasma treatment of aqueous bisphenol A (BPA) solution and mineralization pathways. For the effective contact between plasmatic gas and aqueous BPA solution, the plasma was created inside a porous ceramic tube, which was uniformly dispersed into the aqueous solution through micro-pores of the ceramic tube. Effects of the gas flow rate, applied voltage and treatment time on the decomposition of BPA were examined, and analyses using ultraviolet (UV) spectroscopy, ion chromatography and gas chromatography-mass spectrometry were also performed to elucidate mineralization mechanisms. The appropriate gas flow rate was around $1.0L\;min^{-1}$; when the gas flow rate was too high or too low, the BPA decomposition performance at a given electric power decreased. The increase in the voltage improves the BPA decomposition due to the increased electric power, but the energy required to remove BPA was similar, regardless of the voltage. Under the condition of $1.0L\;min^{-1}$ and 20.8 kV, BPA at an initial concentration of $10L\;min^{-1}$ (volume : 1 L) was successfully treated within 30 min. The intermediates produced by the attack of ozone and hydroxyl radicals on BPA were further oxidized to stable compounds such as acetate, formate and oxalate.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.252-257
• /
• 2023

In this study, to replace phthalate-based plasticizers known as endocrine disruptors, compounds as plasticizer candidates were synthesized by using alcohols containing rings and fatty acids extracted from animal and vegetable oils, and their properties as plasticizers, including their plasticization efficiency, were evaluated. Nine compounds synthesized by esterification of fatty acids (caprylic acid, capric acid, lauric acid) and alcohols (solketal, benzyl alcohol, cyclohexanol) were identified by ¹H-NMR. The nine synthetic compounds were evaluated for their plasticity by adding them to PVC resin, and compared with the commercial plasticizers DEHP, DINCH, and ESO. According to the results, plasticization efficiency was 0.96 to 1.02 times higher than DEHP, 0.94 to 0.98 times higher than ESO, and 1.05 to 1.10 times higher than DINCH. Thermal stability was somewhat lower than that of DEHP and DINCH, but showed better results than ESO. The results of the solvent extraction test showed that both aqueous and oily solvents showed higher values than DEHP and DINCH but showed similar or superior properties to ESO.

• Applied Chemistry for Engineering
• /
• v.34 no.3
• /
• pp.258-263
• /
• 2023

In this study, conductive polymers and the enzyme tyrosinase (Tyr) were deposited on the surface of a screen printed carbon electrode (SPCE), which can be fabricated as a disposable sensor chip, and applied to the detection of bisphenol F (BPF), an endocrine disruptor with proven links to male diseases and thyroid disorders, using electrochemical methods. On the surface of the SPCE working electrode, which was negatively charged by oxygen plasma treatment, a positively charged conductive polymer, poly(diallyldimethyl ammonium chloride) (PDDA), a negatively charged polymer compound, poly(sodium 4-styrenesulfonate) (PSS), and another layer of PDDA were layered by electrostatic attraction in the order of PDDA, PSS, and finally PDDA. Then, a layer of Tyr, which was negatively charged due to pH adjustment to 7.0, was added to create a PDDA-PSS-PDDA-Tyr sensor for BPF. When the electrode sensor is exposed to a BPF solution, which is the substrate and target analyte, 4,4'-methylenebis(cyclohexa-3,5-diene-1,2-dione) is generated by an oxidation reaction with the Tyr enzyme on the electrode surface. The reduction process of the product at 0.1 V (vs. Ag/AgCl) generating 4,4'-methylenebis(benzene-1,2-diol) was measured using cyclic and differential pulse voltammetries, resulting in a change in the peak current with respect to the concentration of BPF. In addition, we compared the detection performance of BPF using an ionic liquid electrolyte as an alternative to phosphate-buffered saline, which has been used in many previous sensing studies. Furthermore, the selectivity of bisphenol S, which acts as an interfering substance with a similar structure to BPF, was investigated. Finally, we demonstrated the practical applicability of the sensor by applying it to analyze the concentration of BPF in real samples prepared in the laboratory.

• Journal of agricultural medicine and community health
• /
• v.30 no.3
• /
• pp.279-292
• /
• 2005

Objectives: The purpose of this study is to analyze agricultural accident and disease using statistical data and materials about National Survey for Health & Nutrition in 2001 and to provide fundamental materials for studies about farmers' health and safety, decision of priority about research and policy. Results: Diagnosed chronic disease prevalence is 72.4% in farmer/fisher group, 49.8% in non farmer/fisher group. The chronic disease prevalence of musculoskeletal disease, circulatory disease, and gastroenteric disease is 46.5%, 18.2%, and 17.9% in farmer/fisher group respectively. The prevalence of musculoskeletal disease in farmer/fisher is 2.4 times higher than non farmer/fisher. This result shows that it need to evaluation for risk factors of musculoskeletal disease preferentially. Lifetime accident/poisoning rate is 18.2% In farmer/fisher group and 13.3% in non farmer/fisher group. The types of accidents were fracture>sprain>contusion and the reasons of accidents were traffic accident>falling/sliding. Conclusions: "Bad or very bad" response of farmer/fisher is almost 2 times higher than non farmer/fisher group. The rate of smoking and no exercising in farmer/fisher group is higher than non farmer/fisher group.