• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1115-1120
• /
• 2000

The purpose of this study is to investigate toughening of unsaturated polyester resin by addition of liquid rubber. In general, unsaturated polyester liquid has strong brittleness in spite of if high strength Therefore; it is difficult use polyurethane liquid rubber for the place where impact resistance is demanded. In this study, it was evaluated strength, impact resistance and fracture toughness by adding to polyurethane liquid rubber(0~25%). As a result, it was found that a tendency to be increase bearing impact and fracture toughness as polyurethane liquid rubber increased but strength was decreased.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.151-154
• /
• 2002

The durability of two kinds of CFRP plates, carbon/UP and carbon/V, was studied under severe environmental conditions. Immersion into the chemical solutions and accelerated weathering were executed on the CFRP plates and the weight change under each condition was measured. After those treatments, the plates were tested by tensile testing machine to measure the mechanical properties and observed by SEM to find the damage behaviour of the surface. Comparing the virgin plates and the chemically exposed plates, both plates show severe deterioration of the mechanical properties. But, the plates subjected to alkali solution show much larger reduction than those of acidic solution and carbon/V has better chemical resistance than carbon/UP. The material properties of CFRP plate exposed to the weathering were deteriorated linearly proportional to the exposure time.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.71-77
• /
• 2001

Unsaturated polyester(UP) resin is one of the major thermosetting resins. It is very useful as the matrix resin of the composite material because of its low viscosity. The polymer resin, however, has several drawbacks; The volume shrinkage occurs during the crosslinking reaction of the UP resin with styrene monomer and the resulting polymer is weak to the alkali and also brittle. The mechanical properties of UP resin can be improved by blending various materials. In this study, polyurethane(PU) was used as a modifier in order to enhance the toughness of the UP resin. The goal of the research is to study the effect of the polyol molecular weight as a PU soft segment and the PU contents on the toughness of PU-modified UP resins. UP/PU polymer network may occur through the reaction between isocyanate group in the methyldiisocyanate(MDI) and hydroxyl group in the UP molecules. The maximum toughness value was shown at 2 wt% of the PU content. This effect results from the incorporation of the PU segment into the UP resin.

• Composites Research
• /
• v.26 no.4
• /
• pp.265-272
• /
• 2013

Fiber-reinforced plastic (FRP) is applied to fabricate the main structures of composite boats. Most of them are made from molds. These products deform after releasing from the mold and they also deform in high temperature environment. Therefore, experimental investigation and evaluation of deformation of laminated composite structures under various manufacturing and working conditions are necessary. The specimens of L-shape and curveshape were made from unsaturated polyester resin and fiberglass material. Input factors (independent variables) are percentage of hardener and manufacturing temperature and four levels of working temperature and output factor is the deformation which is measured on these specimens. From the results, it was observed that the higher the hardener rate and temperature, the lower the deformation. When the working temperature increased, the specimens showed great variations for the initial deformation values. Besides, the values of deformation or input factors could be predicted by regression equations.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1591-1597
• /
• 2012

Adherend samples were made from unsaturated polyester and woven and mat glass fibers by the hand layup and vacuum methods. The mechanical properties of the adhesive, composite adherends, and terminal-joint and secondary-joint specimens were determined experimentally. Combinations of the experiment results and the bonding theory were used in this study. The maximum and average shear stresses were calculated based on the maximum tensile force and geometry parameters of the joint specimens. The results of the maximum and average shear stresses were compared and evaluated for six joints. The results showed that the grinding and grind/acetone joint had the highest strength among three types of terminal-joints. Similarly, the mat-mat and mat-woven joints had the highest strength among three types of secondary-joints with the same value. Conversely, no treatment and woven-woven bonding had very low strength. In each case, failure occurred always at two ends and then moved toward the middle area of the overlap length.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.83-86
• /
• 2001

This paper presents an investigation of the contribution of fibers in energy absorption during impact and the effect of resin types on properties of the high strength polyethylene (Spectra-900 PE) composite. In high strength polyethylene fiber, main impact energy absorbing mechanism was tensile breakage and deformation of fiber. Two types of resin were examined : Unsaturated polyester (UP) and Epoxy. Tensile and 3-point bending test have been performed to investigate the changes of mechanical properties. In tensile and flexural testes, the Spectra Composite prepregged with UP showed higher properties than Spectra Composite prepregged with epoxy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.10a
• /
• pp.269-275
• /
• 2001

정밀가공기계 및 소음발생원의 방진재료로서 사용될 수 있는 재료는 우선 내부 및 외부진동의 흡수성과 감쇠성이 뛰어나야 하고, 시간 및 온도변화에 따라 형상 및 치수 정밀도가 안정되어야 하며, 불규칙한 외력과 운동전달기구의 변동 하중 하에서도 높은 정적, 동적 강성을 유지해야 한다. 본 연구에서 개발한 재료인 Ferrite-Resin 복합재료는 Resin-Concrete에 미세한 산화철을 filler 재료로 사용함으로써 주철 및 강의 구조재료가 갖는 강성과 비중의 값에 접근시킬 수이었다. 일반적으로 불포화 폴리에스테르 수지나 에폭시계 수지는 glass 전위점의 근처에서 진동에너지의 흡수가 큰 영역이 존재하며 이는 10 .mu.m 이내의 미세한 filler재료가 포함되었을 경우에도 그 종류에 관계없이 큰 변화가 없는 성질이다. 시험편을 통한 재료실험을 통하여 개발된 복합재료를 모델 구조물에 적용시킴으로서 그 적용성을 검토하였다. 앞으로의 수지와 Ferrite 함유량 및 제조 공정이 적절히 모색되면, 이 방진재료가 정밀기계의 구조재료로서 뿐만 아니라 냉동기, 소형선박의 기관실, 가전제품 및 기어박스 등의 케이싱 재료로 사용되는 방진재료로서 그 응용이 확대될 수 있을 것으로 본다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.332-335
• /
• 2004

Polymethyl Methacrylate(PMMA) mortars using EPS solution-based binders are prepared with various unsaturated polyester resin(UP) contents of binder, and tested for working life. heat exothorm temperature, length change. compressive strength and temperature dependence of compressive strength. As a result, the working life of PMMA mortar is lengthened with raising UP content of binder. Length change of the mortar was condensed from expansion to shrinkage with increasing UP content, and non shrinkage of the mortar is obtained at about UP content of $2.5\%$. The compressive strength of the mortar is increased with an increase in the UP content and reach maximum at UP content of $5\%$. However thermal resistance improvement of the mortar by increasing UP content was not recognized. UP resin was recommended as an effective agent for shrinkage control and strength development of PMMA mortar.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.343-348
• /
• 1999

The purpose of this study is to evaluated the effects of added expanded polystyrene on the basic properties of UP mortar. Polyester resin mortars are prepared with expanded polystyrene ratio in styrene monomer (EPS/PS), and the ratio of total polystyrene resin to UP resin (PS/UP). And it is tested for viscosity of UP resin added PS resin, slump-flow test, working life, flexural and compressive strengths, and curing shrinkage test. From the test result, Viscosity of resin for polymer mortar increases with increasing PS content. Curing shrinkage of UP mortar is considerably smaller than that of plain UP mortar, nevertheless, reduction in the strengths is not recognized according to adding PS resin. In this study, we can obtain the optimum mix proportions of polymer mortar using PS resin.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2A
• /
• pp.177-184
• /
• 2010

This study was performed to determine the effects of filling materials on the physical properties of permeable polymer concrete. The filling materials were ground calcium carbonate, ground granulated blast furnace slag and fly ash. In this experiment, permeable polymer concrete mixtures with unsaturated polyester resin contents from 5 to 7 weight %, filler/resin ratio of 0~2.0 and crushed coarse aggregate passing 15 mm sieve were prepared and coefficient of permeability, void ratio, compressive strength and flexural strength were tested. As the test results, increase in the strength and decrease in the coefficient of permeability of the permeable polymer concrete were generally observed with increasing the resin contents and filler/resin ratio. The compressive and flexural strength of the permeable polymer concrete were in the range of 8.0 to 35.0 MPa and 2.0 to 9.0 MPa respectively and the highest strength was shown at the mixtures with 7 weight % unsaturated polyester resin contents, 2.0 ratio of filler/resin and filler of ground calcium carbonate. On the other hand, in the level of 20 MPa compressive strength, the mixtures with filler of fly ash was shown as the most economic permeable polymer concrete.