• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.175-181
• /
• 2016

This occurs when the unbalanced rotating body is inconsistent with the mass center line axis geometric center line. Wheelsets are assembled by a single axle with two wheels and a rotating body of a running railway vehicle. Owing to non-uniformity of the wheel material, the wear, and error of the wheel and axle assembly may cause an imbalance. Wheelsets will suffer the effects of vibrations due to the unbalanced mass, which becomes more pronounced due to the thin and high-speed rotation compared to the shaft diameter This can affect the driving safety and the running behavior of a rail car during high-speed running. Therefore, this study examined this unbalanced wheel using a railway vehicle multibody dynamics analysis tool to assess the impact of the dynamic VI-Rail movement of high-speed railway vehicles. Increasing the extent of wheel imbalance on the analysis confirmed that the critical speed of a railway vehicle bogie is reduced and the high-speed traveling dropped below the vehicle dynamic behaviour. Therefore, the adverse effects of the amount of a wheel imbalance on travel highlight the need for management of wheel imbalances. In addition, the static and dynamic management needs of a wheel imbalance need to be presented to the national rail vehicles operating agency.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.158-166
• /
• 2004

A new method to measure residual unbalance of rotor - bearing system was proposed. The method which determine residual unbalance based on polar plot and an analytical method which calculates the residual unbalance of the rotor from the vibration response of the Jeffcott rotor are proposed in this study with respect to a real rotor system of which the residual unbalance is unknown. The unbalance eccentricity of the produced experimental model is 3.78 mil, developing the measurement method of the residual unbalance more convenient than the proposed method of ISO and API standard. The proposed method was experimentally compared with the ISO standard, and the two methods were exactly correspondent to each other within an error of 1%.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.11 s.188
• /
• pp.42-49
• /
• 2006

In this paper error-compensating techniques in three-point weighing method to precisely measure unbalance properties such as center of gravity and unbalance moment. In the conventional static methods, 1) fixture-errors, 2) effects of the contact between the fixture and the load scales, and 3) side effect due to the lateral frictional forces acting on the contact points between the fixture and the load scales are the major factors that lead to measurement errors. The proposed error-compensating method perfectly eliminates both the fixture-error and the contact-error simultaneously by manipulating the three measured reaction forces at three different angular locations. Also the friction-error is calibrated by comparing the sum of three reactions with the actual mass of the specimen. A set of measurement is performed using the same measuring system as Lee's, and a comparison of the results from the convectional, Lee's, and the proposed method is provided. The results show that the proposed method effectively compensates the errors listed above.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.266-271
• /
• 1997

본 연구는 믹서기의 다지기칼날(Mincing Knife)이 구조적으로 가지고 있는 모멘트불평형(Couple Unbalance) 문제를 해결하기 위한 밸런싱방법을 제시한다. 유한요소법에 의하여 칼날에 작용하는 원심력, 정적 불평형량(Static Unbalance) 및 불평형각위치(Unbalance Angle)를 계산하고, 이를 바탕으로 반고리(Semiannular) 형상의 질량을 설계하여 모멘트 밸런싱을 수행하였다. 밸런싱을 수행한 후의 다지기칼날은 분해칼날(Cutting Knife)과 거의 비슷한 동적거동을 가지게 됨을 확인하였다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.5
• /
• pp.529-536
• /
• 2019

In this paper, the signals of the sensor for extracting characteristic parameters of the rotor are collected and the performance of the extraction technique is analyzed. To this end, a vibration test league was developed for conducting model tests to analyze the signal characteristics under normal operation. As a result, it is judged that no change in the measured the raw data amplitude will occur in the acceleration sensor with the unbalanced mass measured from the acceleration sensor. Performing FFT showed a significant increase in amplitude of the rotational frequency of 20 Hz as the unbalanced mass increased. The analysis results according to the change in the unequal mass of the speed sensor also showed a significant increase in the 1X Harmonics component, such as the acceleration sensor. There was no change in the amplitude of the acceleration sensor data when the misalignment occurred, and for the Envelope data, the amplitude of 2X (40 Hz) was increased depending on the degree of misalignment. The velocity sensor at change of misalignment also showed similar results to the acceleration sensor, and the peak was reduced at 600 Hz as the load increased in the frequency spectrum.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.121-126
• /
• 2013

Precision machine tools for high dignity cutting are needed for efforts to improve machining accuracy. However, there are many factors to improve machining accuracy. This study investigated how machining accuracy changes when variation and unbalance amount in rotational speed domain is decreased. Machining accuracy of initial machine tools depends on manufacturing and assembly of parts such as bearing. And then, vibration and noise vary with volume of unbalance amount when it is rotation, so it effects unbalance amount. Also vibration and noise increased by unbalance shorten spindle's life and it especially makes worse boring accuracy. Therefore, this study studied the change of roundness and cylindricity of workpiece when it decreases variation and unbalance in rotational speed domain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.889-898
• /
• 2002

This part of ISO 1940 gives recommendations for determining unbalance and for specifying related quality requirements of rigid rotors; it specifies a) a representation of unbalance in one or two planes; b) methods for determining permissible residual unbalance; c) methods for allocating it to the correction planes; d) methods for identifying he residual unbalance state of a rotor by measurement; e) a summary of errors associated with the residual unbalance identification. This part of ISO 1940 is also intended to facilitate the relations between manufacturer and user of machines. Detailed consideration of errors associated with the determination of residual unbalance is covered in the 2nd part of ISO 1940 (ISO 1940-2 will deal with these errors).

• Journal of the Korea Convergence Society
• /
• v.13 no.4
• /
• pp.307-313
• /
• 2022

The importance of engine vibration reduction is increasing as the vehicle interior noise becomes more serious due to higher output and lighten weight trends. Recently, the balance shaft attachment has been proposed as a representative method for the engine vibration reduction. The balance shaft is a device that cancels the vibrations generated in the reciprocating motion of the piston and the conrod by using an arbitrary eccentric mass, and can improve fuel efficiency and ride comfort at the same time. This paper proposes the unbalance amount and shape of the balance shaft to induce and offset the inertia force generated by the engine structure. The proposed two-shaped balance shaft was implemented as an ADAMS multi-body dynamics model, and the reduction of the inertial force in the actual behavior was confirmed through dynamic simulation.