• 한국분무공학회지
• /
• 제26권3호
• /
• pp.149-156
• /
• 2021

In this study, the behavior of the droplet colliding with parallel wires was analyzed by time-delay photography. The impact behavior modes and the critical capture speed were analyzed by changing fluids, the droplet velocity, the wire diameter and the distance between wires. Seven typical modes of impacting droplet on parallel wires were observed. The tendency of mode change was generally similar when the wire diameter was changed, but the increase of the wire diameter caused the increase of the droplet velocity at which the mode changed. The modes at the highest droplet velocity were the splitting mode when the wires were closest, the passing and splitting mode in the middle, and the passing mode when the wires were farthest apart. The critical capture speed increased as the wire diameter increased and the distance between wires decreased. The ethanol droplet showed the lowest critical capture speed.

• 한국분무공학회지
• /
• 제26권1호
• /
• pp.1-8
• /
• 2021

Droplet evaporation has been known as a common phenomenon in daily life, and it has been widely used for many applications. In particular, the influence of the different heated substrates on evaporation flux and flow characteristics is essential in understanding heat and mass transfer of evaporating droplets. This study aims to simulate the droplet evaporation process by considering variation of thermal property depending on the substrates and the surface temperature. The commercial program of ANSYS Fluent (V.17.2) is used for simulating the conjugated heat transfer in the solid-liquid-vapor domains. Moreover, we adopt the diffusion-limited model to predict the evaporation flux on the different heated substrates. It is found that the evaporation rate significantly changes with the increase in substrate temperature. The evaporation rate substantially varies with different substrates because of variation of thermal property. Also, the droplet evaporates more rapidly as the surface temperature increases owing to an increase in saturation vapor pressure as well as the free convection effect caused by the density gradient.

• 한국분무공학회지
• /
• 제27권4호
• /
• pp.188-194
• /
• 2022

In this study, the behavior of water droplet impacting on a thin horizontal orifice was investigated. The impact behavior modes, transition velocities and diameters of daughter droplets were analyzed by changing the droplet velocity, orifice diameter and orifice thickness. Four typical modes of impacting droplet on an orifice were observed. The single-droplet and double-droplet transition velocities increased with increasing the orifice thickness and decreased with increasing the orifice diameter. On the other hand, the multi-droplet transition velocity decreased and then increased as the orifice diameter increased. At thin orifice thickness, the single droplet diameter approximated the orifice diameter, and increasing the orifice thickness produced a droplet larger than the orifice diameter. In the case of double droplet mode, the diameter of the first droplet showed a similar tendency like the single droplet mode, but the diameter of the second droplet was smaller than that of the first droplet, and the difference between them was affected more by the orifice thickness.

• 대한기계학회논문집B
• /
• 제34권11호
• /
• pp.983-990
• /
• 2010

본 연구에서는 냉각면의 표면온도가 비교적 낮은 강제대류 및 핵비등영역에서 다양한 종류의 마이크로 휜이 가공된 냉각면의 분무냉각 열전달에 대해 실험적으로 연구하였다. 실험결과로부터 냉각면 표면에 가공된 마이크로 휜은 분무냉각 열전달을 촉진시키며, 냉각휜의 크기와 종류에 상관없이 분무유량이 증가할수록 분무냉각 열전달도 큰 폭으로 증가하고 있음을 알 수 있었다. 또한 희박한 분무영역에서는 냉각면에 가공된 휜의 크기와 형상이 분무냉각 열전달에 큰 영향을 미치고 있으나, 분무유량이 증가할수록 이러한 경향은 점차 약해져 본 실험에서 가장 높은 분무유량조건에서는 편평한 냉각면을 제외한 모든 냉각면의 열유속이 거의 동일하게 나타나고 있음을 알 수 있었다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1317-1322
• /
• 2004

In this report, the heat transfer model of spray cooling on hot surface was developed by focusing on the effect of rebound motion of droplets. In the model, it was assumed that droplets rebound repeatedly on the hot surface and heat transfer upon droplet impact is proportional to sensible heat which heats up the droplets to the saturation temperature. In addition, to take account of the contribution of th heat flux upon impact of rebound droplets, it was assumed that the rebound droplets are distributed following the Gaussian distribution from 0 to L, which distance L is determined by maximum flight distance $L_{max}$. Also the calculated results were compared with existing experimental results.

• 한국자동차공학회논문집
• /
• 제3권1호
• /
• pp.118-130
• /
• 1995

Fuel spray in a gasoline engine is a significant factor for the decision of engine power, pollutant emission and the design of intake manifold system. Three kinds of fuel which has other physical properties are chosen in this study, and it is observed using an image processing method that the mechanism and structure of free fuel spray with a throttle type gasoline injector, and the detailed characteristics of droplet size and velocity distributions are obtained by macro and micro-scopic measuring method respectively. It is verified that the initial breakup behaviors are depended on We like the result of Reitz's study, and also observed that the spray of octane and solvent with Re of 210~330 and 270~330 respectively are better than ethanol which has relatively high density and viscosity.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.60-68
• /
• 1996

디젤 엔진의 분사연료를 연소실 내부에 마련된 작은 돌출부에 충돌시켜 액적을 작게 부수고 연료가 연소실 내부에 고루 분포할 수 있도록 하여 여러 가 지 엔진성능향상을 도모한 새로운 디젤 연소실 시스템이 최근 제시되고 있다. 이들 시스템은 피스톤 내부 혹은 엔진헤드 부위에 분사연료 충돌부를 두고 있는데, 여기에서는 이 새로운 시스템 개발에 있어 고려되어야 할 몇 가지 중요 요인들에 중점을 두어 분석하였다. 결과로서 분사압력, 사노즐크기, 주위공기 온도와 압력의 변화가 분무 평균입경과 분무연료의 분포에 미치는 영향을 제시하였다.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.31-38
• /
• 2001

The Holographic Particle Velocimetry system can be a promising optical tool for the measurements of three dimensional particle velocities. In this study, the holographic panicle velocimetry system was used to measure the sizes and velocities of droplets formed by a commercial full cone spray nozzle. Uncertainty analysis was performed to identify the sources of all relevant errors and to evaluate their magnitude. The droplet velocities ranged from 10.3 to 13.3 m/s with average uncertainty of ${\pm}1.6m/s$, which is ${\pm}14%$ of the mean droplet velocity. Compared with relatively small uncertainties of velocity components in the normal direction to the optical axis, the uncertainty of the optical axis component is ${\pm}3.6m/s$. This is due to the long depth of field of droplet images in the optical axis, which is inherent feature of holographic system using forward-scattering object wave of particles.

• 한국분무공학회지
• /
• 제18권3호
• /
• pp.119-125
• /
• 2013

Digital holographic particle velocity measurement system can be a promising optical tool for the measurements of three dimensional particle velocities. In this research, validation experiments for the digital holographic particle velocity measurement system were conducted with measuring the velocities of glass beads on a rotating disk. Uncertainty analysis was performed to identify the sources of all relevant errors and to evaluate their magnitudes. The measurement results of particle velocities obtained with digital holographic method are compared reasonably well with the known values within acceptable range of errors. Moreover, digital holographic method showed better performance compared with that of optical holographic system.

• 한국분무공학회지
• /
• 제7권4호
• /
• pp.23-31
• /
• 2002

In this study, the sizes and velocities of droplets in sprays were measured by image processing method from digital images of local region of sprays. The morphological method based on the Euclidean distance transform, Watershed separation, and perimeter image was adopted for the recognition and separation of overlapped particles. The match probability method was used for the particle tracking and pairing. The measurement results show that the present method may be reliable for the analysis of the motion and distribution of droplets produced by spray and atomization devices.