• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.5
• /
• pp.37-50
• /
• 2007

This study investigated the characteristics of spray generated by a liquid coaxial swirl injector used in a combustor of the liquid rocket engine. The linear stability analysis considered long and short wave was introduced in liquid sheet breakup. Through the hydrodynamic analysis the initial liquid sheet thickness spray angle and injection velocity were predicted. To evaluate the effect of turbulence model standard $k-{\varepsilon}$ and RNC $k-{\varepsilon}$ model were applied to numerical calculation and it was known that RNC $k-{\varepsilon}$ model was more applicable to predict spray characteristics. On the basis of this evaluation validation of the developed model was performed with swirl injector installed in LPRE and the predicted results of breakup length, spray angle, and SMD agreed well with experiments qualitatively and quantitatively.

• Solar Energy
• /
• v.15 no.2
• /
• pp.91-99
• /
• 1995

The influence of deposition parameters on the deposition of $SnO_2$ thin films by spray pyrolysis has been studied. In the case of spray solution with tile concentration of 0.01M, at low deposition temperature the deposition was controlled by surface reaction and portion controlled by mass transfer is increased with increasing deposition temperature to $400^{\circ}C$. Above $400^{\circ}C$, the deposition is controlled by mass transfer at low spray pressure, and by surface reaction at high spray pressure. As the concentration of spray solution increased the deposition rate increased, and in this experiment the deposition depends on the Rideal-Eley mechanism. The deposition rate increased with increasing substrate temperature up to $400^{\circ}C$ and then decreased due to homogeneous nucleation. The thickness of the deposit increased with increasing spray duration, and the adhesion between substrate and deposit was formed physically.

• Korean Journal of Materials Research
• /
• v.6 no.5
• /
• pp.475-482
• /
• 1996

초음파분무를 이용한 MOCVD법으로 강유전 BaTiO3 박막을 제조하였다. 초음파 분무 MOCVD법은 비교적 저온에서도 후열처리없이 결정화된 박막의 제조가 가능하다. 증착한 박막은 기판온도가 증가할수록 (110) 우선 배향성을 가졌으며, 기판온도에 따라서 서로 다른 결정상을 나타내었다. 기판온도가 55$0^{\circ}C$인 경우에 증착한 박막은 결정화가 완전히 진행되지 않았으며, 결정립의 크기도 매우 작아 상온에서 입방정상의 특성을 보였다. $600^{\circ}C$에서 증착한 박막은 결정화가 진행되어 입자의 크기는 성장하였으나 의사 입방정상을유지하고 있었다. 반만 $650^{\circ}C$에서 증착한 박막은 결정화뿐만 아니라 주상으로 성장하여 수직 방향으로는 박막 두께의 크기를 가져 CV 특성에서 이력곡선을 보였으며, 정전용량의 온도 변화에 따른 특성에서도 상전이의 특성을 나타내었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.7
• /
• pp.97-104
• /
• 2006

The spray and breakup characteristics of swirling liquid sheet were investigated by measuring the spray angle and breakup length as the axial Weber number Wel was increased up to 1554 and the ambient gas pressure up to 4.0MPa. As Wel and ambient gas density increased, the disturbances on the annular liquid sheet surface were amplified by the increase of the aerodynamic forces, and thus the liquid sheet disintegrated near from the injector exit. The measured spray angles according to the ambient gas density were different before and after the sheet breaks. Before the liquid sheet breaks, the spray angle was almost constant, but once the liquid sheet started to breakup, the spray angle decreased. And the breakup length decreased because of the increase of the aerodynamic force as the ambient gas density and Wel increased. Lastly, the measured breakup length according to the ambient gas density and Wel was compared with the result by the linear instability theory. We found that the corrected linear instability theory considering the attenuation of sheet thickness agrees well with our experimental results.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.76-80
• /
• 2010

In this study, YDC powders with uniform composition and particle size were synthesized by a citrate method and their thin film deposition was conducted by electrospray deposition method. Polymeric precursor was prepared first by reaction of metal salts with citrate acid and ethylene glycol. Fluorite crystalline YDC powders were obtained by calcining the precursor at $750^{\circ}C$ for 3 h. The electrospray deposited films prepared at the optimum conditions became dense and defect-free after heat treatment at $1400^{\circ}C$ for 3 h. The film thickness was linearly varied with the deposition time.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2007

The low frequency combustion instability phenomena generated by pressure drop oscillation such as propellant shake in feed line are studied. To generate the flowrate oscillation by the pressure pulsation up to 400Hz without flow discontinuities and cavitations, a hydrodynamic mechanical pulsator of rotating disk type was produced. Injection pressure conditions are 5, 7 and 9 bar and pressure fluctuation frequency conditions are 0, 4, 6 and 8 Hz. When the injection pressure was oscillated by a mechanical pulsator, the spray shape was pulsated regularly. During the pulsated state of the spray with a mechanical pulsator, the spray characteristics, such as spray angle and liquid film thickness in orifice exit, were measured and compared with those in steady state without a mechanical pulsator. Though the mean injection pressure was fixed in the steady and fluctuating state, there were some differences in all measured values, i.e. liquid film thickness and spray cone angle, between both states.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.21-29
• /
• 2004

The flow characteristics of a swirl injector were investigated with the variation of the flow condition and geometric dimensions, such as orifice length for considering the viscous effect and tangential entry port area for considering the swirl intensity. The liquid film thickness strongly influencing on the formed drop size of the spray was measured using a new technique. The film thickness measurement technique proposed here, used the attenuation of fluorescence signal near the injector exit. The breakup length that is important for the flame location as well as the spray cone angle which influences on the ignition performance was measured using a backlit stroboscopic photography technique. From the experimental results, it is found that an increase in injection pressure decreased the film thickness and breakup length, and also enlarged the spray cone angle. A decrease in orifice length and tangential entry port area has a similar tendency of thinner film thickness, shorter breakup length and larger spray cone angle. In the present study, we proposed empirical models of the flow characteristics of the swirl injectors.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.211-212
• /
• 2015

이번 실험에서는 건식 도금방법을 이용한 알루미늄 도금강판의 조성 및 두께에 따른 내식성 평가를 염수분무 실험을 통해 측정하였다. 실험 결과 도금 조성 내 Silicon의 조성이 증가할수록, 일반적인 건식도금 방법보다 조직 성장 시 도금 층에 각을 주어 도금하는 것이 내식성을 향상시키는 것으로 관찰되었다.

• Journal of ILASS-Korea
• /
• v.27 no.2
• /
• pp.77-83
• /
• 2022

In this study, the thickness of the liquid sheet formed by a low speed impinging jet onto a flat plate was measured by the direct contact method. The spatial distribution characteristics of the sheet thickness in the radial and circumferential directions, and the effects of jet velocity and liquid viscosity were analyzed. The measurement results were compared with the theoretical predictions. The wavy surface was observed in the case of low viscosity water, but not in the high viscosity aqueous glycerol solutions. The sheet thickness increased as the circumferential angle increased or the distance from the impinging point increased, but the thickness decreased as the circumferential angle increased around the impinging point. As the jet speed increased, the sheet thickness decreased, and the sheet thickness increased as the liquid viscosity increased. Comparison with the theoretical predictions showed that the measurement results agreed well in the case of low viscosity water or high viscosity liquids around the impinging point. The distribution characteristics of the sheet thickness can provide useful means for prediction of spray characteristics in splash plate injectors.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.4
• /
• pp.8-14
• /
• 2015

This study has been done as a preliminary work in the process of confirming the modeling and calculation results on the dynamic characteristics of closed-type swirl injector which were performed by Ismailov et al. in Purdue university. Closed-type swirl injectors with replaceable swirl chamber parts were designed and manufactured. The steady state spray characteristics of closed-type swirl injector with varying swirl chamber length and diameter were verified. Mass flow rate was measured with a mass flow meter installed in front of the injector, and liquid film thickness was measured by Lefebvre's method with electrodes installed at the orifice of the injector. Variation of spray cone angle and break-up length were investigated from the spray images captured under different manifold pressure conditions.