• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.6
• /
• pp.569-577
• /
• 2010

A multiscale particle simulation technique that can be applied to a multiphase fluid system has been developed. In the boundary region where the macroscopic- and microscopic-scale models overlap each other, three distinctive features are introduced in the simulation. First, a wall is set up between the gas and liquid phases to separate them and match the phases respectively to the macroscopic conditions stably. Secondly, the interfacial profile is obtained near the matching region and the wall translates and rotates to accommodate the change in the liquid-vapor interfacial position in the molecular model. The contact angle thus obtained can be sent to the macroscopic model. Finally, a state of mass and temperature in the region is maintained by inserting and deleting the particles. Good matching results are observed in the cases of the complete and partial wetting fluid systems.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.22 no.1
• /
• pp.63-71
• /
• 2004

This research is to reconstruction of railway alignment using GPS data, an investigation is made on the method of optimum simplification for reduction of unnecessary linear data, improve the accuracy by using four simplification algorithms among the methods. By applying two measured of displacement between observed data and it's simplification methods have been evaluated. The results showed that the complexities of lines is not practical to investigate simplification algorithms, the Douglas-Peucker method produced a little displacement between observed data and it's simplification. Its by using the Douglas-Peucker method to observed linear GPS data in railway track, design elements of horizontal alignment have been calculated. Then we could know that obtain the good results fur reconstruction of alignment elements through the methods and algorithns of this study.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.838-845
• /
• 2004

After collecting the scanned images of practical identification licenses, it is attained to more accurate recognition of numbers in the identification licenses. As considering the process speed of the preprocess course for recognition, first, it is divided into eight equal parts of the identification license and then, removed the hologram of correspondent noises. It is run parallel template comparison method and teaming method for the number recognition and in order to extract a simple characteristics of the number the clustering method is used. Also, in case of misrecognized number because of external environment by run parallel with the thinning method, similar each numbers is sectioned by unique characteristics. From the results of number recognition, it is confirmed that the recognition rate of numbers is superior to other Studies.

• Journal of the Institute of Convergence Signal Processing
• /
• v.5 no.3
• /
• pp.173-180
• /
• 2004

In this paper we provide a new image restoration method based on the multiscale regularization in the redundant wavelet transform domain. The proposed method uses the redundant wavelet transform to decompose the single-scale image restoration problem to multiscale ones and applies scale dependent regularization to the decomposed restoration problems. The proposed method recovers sharp edges by applying rather less regularization to wavelet related restorations, while suppressing the resulting noise magnification by the wavelet shrinkage algorithm. The improved performance of the proposed method over more traditional Wiener filtering is shown through numerical experiments.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.42-48
• /
• 2003

To get a periodic trim solution from Level II helicopter flight dynamic equations, DAE based PPT A (partial Periodic Trimming Algorithm) has been proposed. Iterative update of state variables from PPT A can cause a numerical instability in DAE solver which needs compatible initial conditions. By simply adjusting the order of DAE solver a periodic trim can be obtained with good accuracy. Application for CBM (Common Baseline Model) helicopter showed the same trim result as harmonic balance method and the effective elimination of unrealistic initial responses at the start of flight simulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.6
• /
• pp.148-155
• /
• 2008

This study presents a process control of the wafer edge exposure (WEE) used in 300[mm] wafer environment. WEE, as a key module of the overall track system (coater and developer) for making patterns on wafer, is a system to expose the UV-ray on the wafer to remove a photo resist around edge of the wafer. It can measure, memorize and control the distance and angles from wafer center to edge. Recently in the 300[mm] semiconductor fabrication, the track system strongly requires that WEE station has a controller with high throughput and accuracy to increase process efficiency. We have designed and developed the controller, and present here a WEE control algorithm and experimental results.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.4
• /
• pp.308-314
• /
• 2010

Purpose: The purpose of this study is to analyze the change in re-osseointegration over time and bone reaction at the interface between implant fixture and the surface of the bone, after destroying re-osseointegration by distorting the bone-implant interface artificially. Materials and methods: Experimental implant fixtures (cp titanium, ${\phi}3.75\;mm{\times}4\;mm$) which didn't have surface treatment were produced. Two or three fixtures were implanted on both tibias of twelve female rabbits (New Zealand white, more than 3.5 kg). Then after six weeks, removal torque (RT) was measured and the results were recorded as the first measurement values. The fixtures were submerged again to get reosseointegration between the bone and fixture. To identify the change in re-osseointegration of submerged fixtures over time, six groups had the healing time for four days (group I), one week (group II), two weeks (group III), three weeks (group IV), four weeks (group V) and five weeks (group VI), and then the secondary removal torque was measured for each group. To identify the bone formation under fluorescent light, tetracycline (15 mg/kg, IM) were treated on the rabbits of each group. After the second measurement, the rabbits were sacrificed, and 16 slides were made, two or three for each group. The slides were observed under the fluorescent light with light microscope. To find out the change in the secondary removal torque over the primary removal torque in progress of time, the averages of the increase rate of the primary and secondary torque removal force were calculated. Then, to find out if there were any critical differences between the primary removal torque and the secondary removal torque in each group and among the groups, the results were analyzed statistically by paired t- test, one-way ANOVA, and Duncan's Multiple Range Test. Results: In group I and II, secondary removal torque decreased, especially in group I. In group III, IV, V, and VI, secondary removal torque increased critically. Comparing the differences among the groups, the critical difference was shown between group I, II and group III, IV, V, VI. Mineralization at the interface between the bone and implant fixture was identified from the first week, and bone formation was shown more clearly from the second week. Conclusion: If the implant fixture remains unforced for a certain period of time after the fixture has had iatrogenic mobility, re-osseointegration occurs at the surface of the fixture, and for tibias of rabbits, higher re-osseointegration was obtained within two weeks.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.93-93
• /
• 2012

섬유산업은 그 제조 스트림이 높은 오염 부하와 에너지 다소비를 특징으로 하여 환경규제에 따라 기존 시장의 위축 가능성이 상존하고 있다. 특히 섬유산업의 주요 스트림 중의 하나인 염색가공 공정은 섬유에서 불순물을 제거하고 심미한 색상과 사용 목적에 적합한 성능을 부여하는 단계로 섬유제조 공정에서 가장 높은 부가가치를 부여하는 단계이나 고온의 물과 다양한 화공약품을 많이 사용하고 그 처리온도가 비교적 높아($100^{\circ}C$ 이상) 대표적인 폐수 발생 공정이자 에너지 다소비 공정이다. 섬유의 염색 방법 중 반연속방법인 CPB(Cold Pad Batch)염색은 반응성 염료와 알칼리의 혼합액으로 구성된 염액에 원단을 패딩한 후 상온에서 수 시간 배칭하고 수세 및 후처리하여 염색하는 방법으로 작업공정관리, 설비관리가 간편하고 에너지소비량 절감, 높은 생산성의 장점이 있다. CPB염색법은 주로 직물에 적용되어 보편화 되었으며, 작업공정 중 장력의 영향을 많이 받는 니트 소재에 적용되는 사례는 드물다. 직물류의 CPB 염색가공법은 대구 경북을 중심으로 연구진행이 활발히 이루어지고 있어 국내 100대 정도의 CPB 관련 장비가 직물제품에 한정되어 가동되고 있는 반면, 니트 CPB 관련 염색 가공 업체는 1곳에 불과한 실정이나 니트류에 대한 지속적인 수요 증가를 고려하면 니트 소재에 대한 CPB염색 적용은 시의적절한 필수요소라고 판단된다. 니트 소재에 대한 CPB염색가공 적용 시 나타나는 문제점은 작업원단의 변부 말림현상 발생, 전폭 상태에서의 색상차이인 listing현상, 원단의 첫도입부분과 끝부분의 색상차이인 tailing현상이며, 반복되는 작업 시 염색재현성을 확보하는 것으로 나타난다. 본 연구에서는 CPB염색 시 CPB Head 장치의 Padding 방식 즉, trough와 Nip type에 따른 염색 시 알칼리와 염료 투입에 따른 염색 재현성(Build up, Ending, 알칼리 안정성)을 비교해 보았으며, 이에 따른 염색제품의 물성 및 견뢰도를 확인하여 보다 효율적인 방식을 선별하였다.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.5 no.2 s.17
• /
• pp.1-8
• /
• 2005

Microwave tomographic imaging technology using a bi-focusing operator has been developed in order to detect the internal voids/objects inside concrete structures. The imaging system consists of several cylindrical or planar array antennas for transmitting and receiving signals, and a numerical focusing operator is applied to the external signals both in transmitting and in receiving fields. In this study, the authors developed 3-dimensional (3D) electromagnetic (EM) imaging technology to detect such damage and to identify exact location of steel rebars or dowel. The authors have developed sub-surface two-dimensional (2D) imaging technique using tomographic antenna array in previous works. In this study, extending the earlier analytical and experimental works on 2D image reconstruction, a 3D microwave imaging system using tomographic antenna way was developed, and multi-frequency technique was applied to improve quality of the reconstructed image and to reduce background noises. Numerical simulation demonstrated that a sub-surface image can be successfully reconstructed by using the proposed tomographic imaging technology. For the experimental verification, a prototype antenna array was fabricated and tested on a concrete specimen.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.2
• /
• pp.173-181
• /
• 2014

In this paper, the algorithm that can automatically segment the lung, the airway and the pulmonary vessels in a chest CT was proposed. The proposed method is progressed in three steps. In the first step, the lung and the airway are segmented by the region growing law through the optimal threshold and three-dimensional labeling. In the second, from the start point to the first carina of the airway is segmented by the deduction operation, and the next airway of the bifurcations are segmented by applying a variable threshold technique. In the third step, the left/right lungs are divided by the restoration process for the lung, and the outside of lungs for abnormal is checked by applying the advanced rolling ball algorithm, and if abnormal is found, that part is removed, and it is restored to the normal lungs by connecting the outside of the lung in the form of second-order polynomial. Finally, pulmonary vessels are segmented by applying the three-dimensional connected component labeling method and three-dimensional region growing method. As the results of simulation, it could be confirmed that the pulmonary vascular is accurately divided without loss of tissue around lung.