• Title/Summary/Keyword: 부분용융

Search Result 191, Processing Time 0.024 seconds

Evaluation of Granite Melting Technique for Deep Borehole Sealing (심부시추공 밀봉을 위한 화강암 용융거동 평가)

  • Lee, Minsoo;Lee, Jongyoul;Ji, Sung-Hoon
    • Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
    • /
    • v.16 no.4
    • /
    • pp.479-490
    • /
    • 2018
  • The granite melting concept, which was suggested by Gibb's group for the closing of a deep borehole, was experimentally checked for KURT granite. The granite melting experiments were performed in two pressure conditions of atmospheric melting with certain inorganic additives and high pressure melting formed by water vaporization. The results of atmospheric tests showed that KURT granite started to melt at a lower temperature of $1,000^{\circ}C$ with NaOH addition and that needle shaped crystals were formed around partially melted crystals. In high pressure tests, vapor pressure was increased by adding water with maximum pressure of about 400 bars. KURT granite was partially melted at $1,000^{\circ}C$ when vapor pressure was low. However, it was not melted at vapor pressures higher than 200 bars. Therefore, it was determined that high pressure with a small amount of water vapor more effectively decreased the melting point of granite. Meanwhile, high temperature and high pressure vapor caused severe corrosion of the reactor wall.

Paleoproterozoic Hot Orogenesis Recorded in the Yeongnam Massif, Korea (영남육괴에 기록된 고원생대 고온조산운동)

  • Lee, Yuyoung;Cho, Moonsup
    • Korean Journal of Mineralogy and Petrology
    • /
    • v.35 no.3
    • /
    • pp.199-214
    • /
    • 2022
  • The Yeongnam Massif is one of representative basement provinces in the Korean Peninsula, which has experienced high-temperature, low-pressure (HTLP) regional metamorphism and partial melting. Here we reviewed recent developments in Paleoproterozoic (1.87-1.84 Ga) hot orogenesis of the Yeongnam Massif, typified by the granulite-facies metamorphism and partial melting recorded in the HTLP rocks. In particular, spatiotemporal linkage between the metamorphic and magmatic activities, including the Sancheong-Hadong anorthositic magma as a heat source, provides a key to understand the widespread HTLP metamorphism and partial melting in the Yeongnam Massif. Crustal anatexis, resulting from the fluid-present melting and muscovite/biotite dehydration melting, has yielded various types of leucosomes and leucogranites. Zircon and monazite petrochronology, using in-situ U(-Th)-Pb data from the secondary ion mass spectrometry, indicates that the HTLP metamorphism and anatexis lasted over a period of ~15 Ma at ca. 1870-1854 Ma. In addition, a fluid influx event at ca. 1840 Ma was locally recognized by the occurrence of incipient charnockite. Taken together, the Yeongnam Massif preserves a prolonged evolutionary record of the HTLP metamorphism, partial melting, and fluid influx diagnostic for a hot orogen. Such an orogen is linked to the Paleoproterozoic orogeny widespread in the North China Craton, and most likely represents the final phase of crustal evolution in the Columbia/Nuna supercontinent.

Arc Welding에서의 Bead의 생成機構

  • 중근금작
    • Journal of the KSME
    • /
    • v.19 no.4
    • /
    • pp.279-290
    • /
    • 1979
  • Arc Welding의 경우 arc열에 의하여 생성된 용융지(Molten Pool)가 응고하는 과정은 금형주물의 응고과정과 비슷하게 생각되나 실은 응고의 제1단계에서 양자간에 큰 차이가 있다. 즉, 금형에 주입된 용융금속이 응고하는 경우는 금형과 이에 접한 주조금속과는 응고후 별도로 분리할 수 있으며, 양자가 서로 융합해서는 안될 것이다. 이에 반하여 융접의 경우에는 금형속에 있는 용 융금속과 금형이라고 볼 수 있는 모재용융부단면과는 완전히 융합되어야 할 것이다. 금형주조 부분의 응고에서는 금형에 접한 주조금속이 열적과냉각(Thermal Supercooling)을 받아 그 내부에 결정핵이 생성되어 이것이 성장하는 과정을 거칠 것이다. 그러나 융접의 경우에는 일반적으로 용융금속과 모재와는 통일계통의 재료이므로 용융금속에 접한 모재부분 자신이 종자결정(Seed Crystal)와 같은 역할을 하여 용융금속내에 새로히 결정핵을 생성함이 없이 이 위에서 직접 결 정성장이 연행되는 것이다. 이것을 Epitaxial Growth라는 하나 이것이 용접부의 응고에서의 큰 특정인 것이다. 주조, 용접 공히 열절과냉각에 의한 응고의 초기단계를 거치면 합금인 경우 그 후의 응고과정은 주로 조성적 과냉각(Constitutional Supercooling)에 따르게 될 것이다. 이 기 회에 Epitaxy에 관해서 간단히 설명하고저 한다.

  • PDF

Calculation of Surface Tension of Liquid Alloys Using Thermodynamic Software (열역학 소프트웨어를 이용한 용융 합금의 표면 장력 계산)

  • Gang, Yun-Bae
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2015.11a
    • /
    • pp.213-214
    • /
    • 2015
  • 용융 합금의 표면 장력은 도금, 용접등 금속 제조 공정중 큰 영향을 미치는 재료의 물성 중 하나이다. 표면 장력의 측정을 위해 다양한 방법이 개발 되었으며 많은 합금계에 대해 표면 장력값이 온도와 조성의 변화에 대해 알려져 있다. 그럼에도 불구하고 실험 측정의 어려움, 실용적인 다원계 합금에서의 표면 장력 측정치의 부족으로 인해 전술한 금속 제조 공정에서 나타나는 현상에 대한 해석에 사용하기에 아직 해결해야 할 부분들이 많이 있다. 본 연구에서는 표면 장력이 합금의 Gibbs free energy의 한 부분으로 기술되는 열역학 원리 및 표면 장력이 Gibbs energy 수식 내 표면적에 대응하는 포텐셜 함수로 얻을수 있다는 Pajarre등의 제안에 근거하여 용융합금의 표면 장력을 계산하는 방법을 제시한다. 다양한 열역학 성질과 상태도를 계산하기 위해 개발된 열역학 소프트웨어 및 데이터베이스를 활용하여 2원계-다원계 용융 합금의 표면장력을 계산하고 이를 알려진 실험 자료와 비교하였다. 철강 제품의 표면 도금에 사용되는 용융 아연 합금의 표면 장력을 전술한 방법을 통해 예측하고 그 결과를 토의한다.

  • PDF

Heat Transfer Characteristics for Inward Melting in a Horizontal Cylinder (수평원통관 내에서 용융이 일어날 때의 열전달특성)

  • Yum, Sung-Bae;Hong, Chang-Shik
    • Solar Energy
    • /
    • v.10 no.2
    • /
    • pp.44-58
    • /
    • 1990
  • Heat transfer characteristics of heat storing processes in paraffin-filled horizontal circular cylinder is studied. The unmelted solid paraffin is allowed to fall on the bottom wall under gravity. In the upper liquid phase, natural convection is considered to take place while in the lower liquid film between the solid paraffin and the wall conduction is thought to take place instead. Experimental analyses are also carried out. The amount of the latent heat stored is obtained by recording the time wisely changing side area of the solid paraffin photographically. The mass of paraffin melted in the upper section is obtained by substracting the amount of melted mass in the lower section from the total mass melted and therefrom variation of heat transfer rate in each section is studied.

  • PDF

Petrology and Geochemistry of Jurassic Daejeon and Nonsan Granitoids in the Ogcheon Fold Belt, Korea (옥천(沃川) 변성대(變成帶)에 분포하는 쥬라기(紀) 대전(大田) 및 논산(論山) 화강암류(花崗岩類)의 암석지화학적(岩石地化學的) 연구(硏究))

  • Hong, Young Kook
    • Economic and Environmental Geology
    • /
    • v.17 no.3
    • /
    • pp.179-195
    • /
    • 1984
  • The Jurassic Daejeon and Nonsan granitoids are "S-type" syntectonic calc-alkaline two-mica monzogranite and granodiorite, respectively. With evidences of high CaO, $Al_2O_3$, LIL/HFS elements, total REE, (Ce/Yb)N and initial ($^{87}Sr/^{88}Sr$) ratio, and no significant Eu anomaly, the primary magmas for the Daejeon and Nonsan granitic rocks are derived from partial melting of the Precambrian granulite (e.g. grey gneisses). But those Jurassic granitoids crystallised from different chemical characteristics of parental magmas which is mainly due to varying degree of partial melting of the granulite (crustal anatexis). The absence of significant anomalous Eu($Eu/Eu^*=O.82{\sim}1.00$) in the Daejeon and Nonsan granitoids could indicate that feldspars, mainly plagioclase, did not separate from the magmas. The parental hydrous magmas could not rise appreciably above their source region before crystallisation. The Jurassic granitoids may be resulted by closing-collision situation and belong to the Hercynotype (Pitcher 1979) such as compressive ductile regime of an intracontinental orogen.

  • PDF

용접공정에서의 최적 열 입력 계획

  • 원윤재;조형석
    • Proceedings of the Korean Society of Precision Engineering Conference
    • /
    • 1990.04a
    • /
    • pp.28-35
    • /
    • 1990
  • 용접은 금속을 접합시키는 공정으로서 용접 결과 원하는 용융부 크기(용융 깊이, 용융 폭)를 달성하여야 하고, 이와 같은 목적으로 준 정상 상태에서 얻고자 하는 용융부 크기를 얻을 수 있는 용접 조건을 찾아 이 조건으로 일정하게 유지하면서 용접을 시행하는 것이 보통이다. 그러나, 이 경우에도 용접 초기와 말기 부분과 같은 과도 상태에서는 얻고자 하는 용융부 크기를 얻을 수 없으므로 용접 중 용융부 크기를 일정한 상태로 유지하기 위해서는 이러한 과도 상태에서는 준 정상상태에서의 용접 조건과 다르게 해 줄 필요성이 있다. 따라서, 본 연구에서는 용융부의 크기를 나타내 주는 온도 분포, 모델을 이용하여 과도 상태에서도 원하는 용융부의 크기를 얻을 수 있도록 하는 최소에너지의 열 입력을 구하는 방법을 제시하고 이로 인한 효과를 알아 보았다.

용융아연도금에서 Bi 첨가의 영향

  • 김선규;유정식
    • Proceedings of the Korean Institute of Surface Engineering Conference
    • /
    • 2003.05a
    • /
    • pp.20-20
    • /
    • 2003
  • 용융아연도금은 내식성 아연코팅목적으로 산업체에서 광범위하게 사용되고 있다. 이 공정에서 아연의 배출성능이 나쁜 관계로 피처리물의 끝부분에 고드름이 생기거나 작은 구멍을 메우는 문제가 종종 발생한다. 본 연구에서는 용융아연욕에 Bi를 단독 첨가하거나 Bi와 AI을 함께 첨가하여 이 문제를 해결하였다. Bi의 첨가는 아연의 배출성능을 현저하게 증가시켰으며 0.1 wt.% Bi, 0.025~0.05 wt.% AI을 함유한 용융아연욕에서 가장 균일성이 좋은 코팅층을 얻을 수 있었다. 산업현장 적용시험 결과 아연의 수율을 향상시켰고 드로스의 형성량이 감소하였다.

  • PDF

Peroxide Modification of Nylon 12 Elastomer (Peroxide 개질에 따른 Nylon 12 elastomer의 특성 연구)

  • Choi, Myung-Chan;Jung, Ji-Yeon;Chang, Young-Wook
    • Elastomers and Composites
    • /
    • v.48 no.1
    • /
    • pp.18-23
    • /
    • 2013
  • Nylon 12 elastomer was slightly crosslinked in molten state by the addition of small amount of dicumyl peroxide (DCP) as a crosslink agent and triallycyanuate (TAC) as a co-agent during melt compounding at $160^{\circ}C$ in an internal mixer. The effect of the peroxide crosslinking on mechanical, dynamic mechanical and rheological properties of the nylon 12 elastomer was investigated by means of tensile testing, dynamic mechanical analysis (DMA) and small amplitude oscillating rheometer, respectively. With modification, there is an improvement in tensile modulus and Young's modulus with decease in elongation at break. DMA results for peroxide modified nylon 12 elastomers demonstrated that the glass transiaiton temperature of PTMG segment shifted to higher temperature and the storage modulus remained constant above the melting temperature of nylon 12 segments. Melt rheological studies revealed that the peroxide modified nylon 12 elastomer exhibited a more solid like behavior and stronger shear thinning behavior compared to neat nylon 12 elastomer, which was more prominent at higher TAC content in the polymer matrix. The peroxide modified nylon 12 elastomer exhibited good elastic recoverability and improved mechanical properties without sacrificing melt processibilty, and especially the service temperature range increased as compared to neat nylon 12 elastomer.

Studies on the Draw Resonance in the Melt Spinning of polypropylene/Polyethylene Blends -Rheological Properties and Draw Resonance of Polypropylene/Polyethylene Blends - (폴리프로필렌/폴리에틸렌 혼합물의 용융방사에 있어서 연신공명에 관한 연구 -폴리 프로필렌/폴리에틸렌 혼합물의 유변학적 특성과 연신공명 -)

  • 김상용
    • The Korean Journal of Rheology
    • /
    • v.4 no.2
    • /
    • pp.148-160
    • /
    • 1992
  • 폴리프로필렌(PP)과 폴리에틸렌(PE)혼합물의 용융방사에 있어서 불안정성을 연구하 였으며 혼합물의 유변학적 성질, 혼합물의 형태학적 특성과 연신공명과의 관계를 고찰한 것 이다. 신장점도는 spinline rheometer를 사용하여 측정하여 섬유직경은 광센서를 이용하여 방사공정에서 on-line 측정하였고 연신공명의 주기는 Fourier 변환을 이용하여 분석하였다. PP와 PE혼합물의 용융방사에 있어서 PP 함유량이 많을수록 연신공명이 발생하는 임계연신 비가 줄어들고 그 주기는 길어진다. 정상상태에서 구한 유변학적 성질을 이용하여 Shah와 Pearson의 이론식과 Fisher와 Denn의 이론식으로부터 구한 임계연신비값이 실험치와 많은 차이를 보여주었다. 연신공명에 의하여 형성된 섬유의 가는 부분의 배향도는 굵은 부분에 비하여 크게 향상되었으며 PP 함유량이 많을수록 배향도가 크게 증가하였다.

  • PDF