• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.558-561
• /
• 2010

본 연구에서는 나노복합재의 탄소성 거동과 항복응력을 예측하기 위해 분자동역학 전산모사를 수행하였다. 나일론 기지와 실리카 나노입자가 포함된 단위 셀 구조로부터 나노입자의 체적분율 변화에 따른 응력-변형률 선도를 등변형률을 적용한 등온등압 앙상블 전산모사로부터 도출하였다. 4%의 변형률 범위에서 나노복합재의 탄성계수를 도출하였고, 이를 이용하여 2% 오프셋 방법으로 항복응력을 예측하였다. 나노입자의 유무에 따른 항복평면의 변화와 고분자 재료에서 나타나는 정수압 효과가 항복평면에 미치는 영향을 확인하기 위해 일축 인장/압축 그리고 이축 인장/압축을 수행하였고, 각각의 경우에 나타나는 나노복합재 내부의 자유체적 변화에 대한 분석을 통해 나노입자의 강화효과를 고찰하였다. 또한 고분자 기지로 인해 발생하는 정수압 효과를 반영한 von-Miss 항복평면을 도출하고, 입자의 체적분율 변화에 따른 항복응력의 예측이 가능하도록 정수압효과에 대한 파라메터를 체적분율의 함수로 근사하였다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.7 no.1
• /
• pp.51-61
• /
• 2005

In general the strength parameter of the ground will be changed by reinforcing the ground around tunnel. In this case, the concept of tunnel design, such as supporting system, excavation, lining and so on, should be modified based on the failure criteria or the ground changed by the reinforcement. This paper presents the variation mechanism of strength parameters and new failure criteria of the reinforced ground. In order to perform this research, theoretical and experimental works were carried out. It was clearly founded that the cohesion of strength parameters is only increased by reinforcement of ground, especially by rock bolting.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.2
• /
• pp.80-91
• /
• 1999

This paper presents the stress-strain , volumetric strain characteristics of the Pocheon weathered residual granite soil with variation of the initial water content under drained conditions. A series of consolidated drained triaxial compressiion tests and isotrpc compression tests with various initial water content on specimens were performed. All material parameters of Lade's double work hardening model were determined by using the results of tests. Most aspects of the soil behavior measured in the triaxial compression tests were reproduced with good accuracy by the constitutive model . Therefore double work hardening model has been shown to be applicable to weathered residual granite soil.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.4
• /
• pp.1227-1240
• /
• 2014

Abandoned mines often cause environmental problems, such as alteration of landscape, metal contamination, and landslides due to a heavy rainfall. Geotechnical and rheological tests were performed on waste materials corrected from Imgi waste rock dump, located in Busan Metropolitan City. Debris flow mobility was examined with the help of 1-D BING model which was often simulated in both subaerial and subaqueous environments. To determine flow curve, we used a vane-penetrated rheometer. The shear stress (${\tau}$)-shear rate (${\dot{\gamma}}$) and viscosity(${\eta}$)-shear rate (${\dot{\gamma}}$) relationships were plotted using a shear stress control mode. Well-known rheological models, such as Bingham, bilinear, Herschel-Bulkley, Power-law, and Papanastasiou concepts, were compared to the rheological data. From the test results, we found that the tested waste materials exhibited a typical shear shinning behavior in ${\tau}$-${\dot{\gamma}}$ and and ${\eta}$-${\dot{\gamma}}$ plots, but the Bingham behavior is often observed when the water contents increased. The test results show that experimental data are in good agreement with rheological models in the post-failure stage during shearing. Based on the rheological properties (i.e., Bingham yield stress and viscosity as a function of the volumetric concentration of sediment) of waste materials, initial flowing shape (5 m, 10 m, and 15 m) and yield stress (100 Pa, 200 Pa, 300 Pa, and 500 Pa) were input to simulate the debris flow motion. As a result, the runout distance and front velocity of debris flow are in inverse propositional to yield stress. In particular, when the yield stress is less than 500 Pa, most of failed masses can flow into the stream, resulting in a water contamination.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.6
• /
• pp.488-495
• /
• 2008

In order to achieve long fatigue lifetimes for cyclically pressurized thick cylinders, multi-layered compound cylinder has been proposed. Such compound cylinder involves a shrink-fit procedure incorporating a monobloc tube which has previously undergone autofrettage. The basic autofrettage theory assumes elastic-perfectly plastic behaviour. Because of the Bauschinger effect and strain-hardening, most materials do not display elastic-perfectly plastic properties and consequently various autofrettage mo dels are based on different simplified material strain-hardening models, which is assumed that combination of linear strain-hardenig and power strain-hardening model. This approach gives a more accurate prediction than the elastic-perfectly plastic model and is suitable for different strain-hardening materials. In this paper, a general autofrettage model that incorporates the material strain-hardening relationship and the Bauschinger effect, based upon the actual tensile-compressive stress-strain curve of a material was proposed. The model was obtained using the von Mises yield criterion and plane strain condition. The tensile-compressive stress-strain curve was obtained by experiment. The parameters needed in the model were determined by fitting the actual tensile-compressive curve of the material. Finally, strain- hardening model was compared with elastic-perfectly plastic model.

• Journal of Navigation and Port Research
• /
• v.30 no.8 s.114
• /
• pp.711-719
• /
• 2006

A series of geotechnical centrifuge model tests and numerical modelling have been performed to study engineering characteristics of the composite ground reinforced by both the Sand Compaction Piles(SCPs) and the deformation-reducing sheet piles. The research has covered several key issues such as the load-settlement relation, the stress concentration ratio and the final water content of the ground Totally three centrifuge tests have been conducted by changing configuration of the sheet piles, i.e., a test without the sheet pile, a test with the sheet pile at a single side and a test with the sheet piles at the both sides. In the model tests, a vertical load was applied in-flight on the ground surface. On the other hand, class-C type numerical modelling has been performed by using the SAGE-CRISP to compare the centrifuge test results using an elasto-plastic model for SCPs and the Modified Cam Clay model for the soft clay. It has been found that the sheet piles can restraint failure of foundation, thereby increasing yield stress of the ground. The stress concentration ratio was in the range of $2{\sim}4$. In addition, numerical analysis results showed reductions both in the ground heave($20{\sim}30%$) and in the horizontal movement($28{\sim}43%$), demonstrating the deformation-reducing effect of the sheet piles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.663-670
• /
• 2020

A study on mechanical property characterization and modeling technique was carried out to approximate the behaviour of structures with 2.5D C/SiC material. Several tensile tests were performed to analyze the behaviour characteristics of the 2.5D C/SiC material and elastic property was characterized by applying a mathematical homogenization and a modified rule of mixture. SiC matrix representing the elasto-plastic behavior approximates as a bilinear function. Then the equivalent yield strength and equivalent plastic stiffness were calculated by minimizing errors in experiment and approximation. RVE(Representative Volume Element)was defined from the fiber and matrix configuration of 2.5D C/SiC and a process of calculating the effective stiffness matrix by applying the modified rule of mixture to RVE was implemented in the ABAQUS User-defined subroutine. Finite element analysis was performed by applying the mechanical properties of fiber and matrix calculated based on the proposed process, and the results were in good agreement with the experimental results.