• Journal of Welding and Joining
• /
• v.32 no.5
• /
• pp.72-79
• /
• 2014

Shaped charge(SC) ammunition is a weapon that penetrates directly the target by made jet from metal liner on impacting at a target. In SC, the liner occupies significantly important role causing an explosion and penetration of the target. The Al-Ni composite coating was deposited on copper liner in a solid state via kinetic spraying to improve the explosive force. The mechanical properties, reactivity and microstructure were investigated to confirm the possibility of kinetic sprayed Al/Ni composite coating as a reactive liner material. Reactive liner using Al/Ni composite exhibited much enhanced reactivity than pure copper liner due to Self-propagating High-temperature Synthesis (SHS) reaction with significantly improved adhesive bond strength. Especially, among the Al/Ni composite coatings, AN11 (the Al versus Ni atomic percent ratio is 1:1) showed the greatest reactivity due to its widest reaction area between deposited Al and Ni.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.106.1-106.1
• /
• 2012

EBSD(Electron BackScattered Diffraction)분석은 주사전자현미경에서 관찰되는 비교적 넓은 영역의 결정 방위를 측정하여 집합조직을 해석하는 동시에 결정 방위의 변화를 기준으로 결정립계를 구분 지어 미세조직의 정량 분석도 가능하기 때문에 많은 연구자들이 사용하고 있다. 그러나 EBSD의 Kikuchi 패턴은 시편 표면으로부터 30~50nm 깊이 범위의 표면층으로부터 방출되기 때문에 EBSD 분석 결과는 시편의 표면 처리 상태에 크게 영향을 받아 적절한 시편준비법이 요구된다. 시편 준비 과정 중에 생기는 변형층, 산화층이나 오염층이 10nm 이내로 제어되지 못하면 명확한 패턴을 얻지 못하여 분석이 어려운 경우가 많으므로, 시료의 절단과 연마 과정 중에 변형층을 되도록 적게 만들고 표면의 산화나 오염을 최대한 방지해야 한다. 또한 EBSD 분석 특성상 시편을 70도로 기울이기 때문에 시편의 요철이 심하면 볼록한 영역에 의해 오목한 영역의 패턴이 가려져 결정방위 정보를 얻기 힘들다. 이런 이유로 시편을 최대한 평평하게 하고 요철이 생기지 않게 시편 준비를 하는 것이 관건이다. 금속재료의 EBSD 시편준비법으로는 일반적으로 기계적 연마법과 전해연마법이 주로 쓰인다. 경한 석출물이나 개재물이 연한 기지에 분산되어 있는 시편이나 이종 소재 접합재의 경우는 전해연마법을 사용하면 특정 상(혹은 합금)이 먼저 연마되어 큰 단차가 생기거나 석출물에 의해 요철이 심해져서 정량적인 EBSD 분석이 어렵게 된다. 이 연구에서는 시편 준비가 어렵다고 알려진 다상 금속재료에서의 EBSD 분석 사례를 소개한다. Ti-6Al-4Fe-0.25Si 시효처리합금, 알루미늄 기지 복합재료, 마찰교반용접한 알루미늄-타이타늄합금의 EBSD 시편준비법과 그 분석 결과를 고찰한다.

• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.105-111
• /
• 2000

The wear behavior of thermal sprayed AlSiMg-40TiC composite coatings were studied as a function of load and sliding velocity under unlubricated conditions. Experiments were performed using a block-on-ring(WC-6wt%/Co, Hv 1500) type. The tests were carried out a various load(30∼ 125.5N) and sliding velocity(0.5∼2.0m/s). Three wear rate regions were observed in the AlSiMg-40TiC composite coatings. The wear rate in region I at low load (less then 8N( were less than 1×{TEX}$10^{-5}${/TEX}㎣/m. Low wear rates in region I resulted from the load-bearing capacity of TiC particles. The transition from region I to II occurred when the applied load exceeded the fracture and pull-out strength of the particles. The TiC fractured particles trapped between the specimen and the counterface acted as third-body abrasive wear. The subsurface layer worn surface in region II was composed of the mechanically mixed layer (MML). The wear rate increase abruptly above a critical load (region III). The high wear rate in region III was induced by frictional temperature and involves massive surface damage.

• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.98-104
• /
• 2000

Aluminum alloys are being employed in automobile parts as strive to reduce overall vehicle weight to meet demands for improved fuel economy and reduction in vehicle emissions. Al-based composites reinforced with ceramic ($Al_2O_3,\;SiC,\;TiC\;and\;B_4C$) applications in a variety of components in automotive engines, such as liners, where the tribological properties of the material are important. In this study, Al-base composites reinforced with TiC particle powders has been developed for producing plasma spray coatings. The composite plasma spray powders were prepared Al-13Si-3Mg(wt%) alloy with TiC(40, 60 and 80wt%) particles ($0.2~5{\mu}textrm{m}$) by drum type ball milling. The composite powders ($36~76{\mu}textrm{m}$) were sprayed with plasma torch. Plasma sprayed coatings were heat-treated at $500^{\circ}C$ for 3 hours. The wear resistances of the plasma sprayed coatings were found to decrease with increasing TiC content and improved with heat treatment. AlSiMg-40% TiC heat-treated coatings were showed the best wear resistance in this study.

• Journal of Welding and Joining
• /
• v.23 no.6
• /
• pp.67-71
• /
• 2005

This paper is concerned with a study on fracture strength of composites in an adhesive single lap joint. The tests were carried out on joint specimens made with hybrid stacked composites consisting of the polyester and bamboo natural fiber layer. The main objective of this work was to evaluate the fracture properties adjacent to adhesive bonded joint of natural fiber reinforced composite specimens. From the results, natural fiber reinforced composites have lower tensile strength than the original polyester. But tensile-shear strength of natural fiber reinforced composites with bamboo layer far from adhesive bond is as high as that of the original polyester adhesive bonded joints. Spew filet at the end of the overlap reduced the stress concentration at the bonded area. Spew fillet and position of bamboo natural fiber layer have a peat effect on the tensile-shear strength of natural fiber reinforced composites including adhesive bonded joints.

• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.214-219
• /
• 2019

In this study, the microstructure and characterization of an overlay welding layer using Fe-based composite powders are reported. The effects of the number of passes and composition of powders on the microstructure and mechanical properties are investigated in detail. The welding wire and powders are deposited twice on a stainless-steel rod using a laser overlay welding process. The microstructure and structural characterization are performed by scanning electron microscopy and X-ray diffraction. The mechanical properties of the first and second overlay layers are analyzed through the micro-Vickers-hardness tester and abrasion wear tester. In the second overlay layer, the hardness and specific wear are approximately 840 Hv and $2.0{\times}10^{-5}mm^3/Nm$, respectively. It is suggested that the increase of the volume fractions of $(Cr,Fe)_7C_3$ and NbC phases in the second welding layer enhances the hardness and wear resistance.

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.33-43
• /
• 2016

Grinding, weld deposition, type A sleeve, type B sleeve, composite sleeve, hot tapping and clamp are used as the method to repair the buried pipelines in the United States, UK and Europe. In the event of defect to the pipeline, they have repaired the pipeline through the fitness-for-service assessments. In addition, they have guidelines for the possible repair methods to apply to each type of damage, which is occurred due to the 3rd party construction or corrosion. According to the KGS FS551, Safety Validation in Detail including ECDA(External Corrosion Direct Assessment) as one method of integrity management should be carried out for the old pipeline which supply natural gas as the middle pressure in Korea. Where a defect on the pipelines is found, on the result of Safety Validation in Detail, the pipelines should be repaired or replaced by new piping. However, there are no guidelines or regulations regarding the repair and reinforcement of pipeline, so that, cutting the damaged pipeline and replacing it as a segment of new pipe is the only way in Korea until now. We have suggested pipeline repair methods including type A, B sleeve, composite sleeve, after the survey of foreign repair method and standards including the method of United States and the United Kingdom, and after analysis of the results on pipeline repair test including type A, type B sleeve and composite sleeve.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.71-71
• /
• 2009

전자제품의 다양한 기능들의 융복합화 및 휴대 편의성 경향은 이제 더 이상 새로운 것이 아니다. 이러한 추세에 따라 전자부품들은 모듈화 되고, 휴대하기 용이해 지고 있다. 또한 다양한 제품 디자인에 적용하기 위해 제품에 장착되는 부품의 기구적 위치 배열의 한계 또한 제약 받고 있다. 따라서 최근의 전자부품은 모듈화 되고 있으며, 기구적 한계를 극복하기 위한 Flexible 모듈의 사용이 증가하고 있다. 또한 양산측면에서 Roll-to-Roll(R2R) 방식을 적용함으로써 생산성을 극대화 하고 있다. 이때 R2R 적용을 위해서는 제품이 굴곡 될 수 있도록 유연성이 보장되는 Bendable 전자모듈의 개발이 필수적으로 요구되고 있다. Flexible 기판은 더 이상 새로운 기술이 아니지만, Felxible 기판 내부에 칩이 내장되고, 회로가 형성되어 자체적으로 기능을 수행할 수 있도록 한 Bendable 전자모듈을 R2R 방식으로 제조하는 기술은 매우 새로운 접근이라 할 수 있다. 이러한 기술개발이 현실화 된다면, Wearable Electronics 및 Flexible Display 등 다양한 전자제품에 응용될 수 있을 것으로 기대된다. 그러나 이러한 제품의 상용화를 위해서는 Bendable 전자모듈에 대한 신뢰성이 확보되고, 제품으로써의 수명이 보증되어야 한다. 신규 개발되는 제품의 신뢰성 검증항목이나 수명평가 모델은 현재까지 제안되지 않고 있는 실정이다. 또한 다양한 사용 환경에서 고장(Failure) 발생을 유발하는 스트레스 인자(Stress Factor)를 도출함으로써, 가속시험 또는 신뢰성 검증을 위한 인가 스트레스를 선정할 수 있다. 그러나 이러한 고장물리를 기반으로 스트레스 인자를 해석한 결과는 아직 보고되고 있지 않다. 따라서 본 연구에서는 $50{\mu}m$ 두께의 Si Chip에 저항변화를 관찰하기 위한 회로를 형성한 후 폴리이미드 기판을 이용하여 Si Chip이 임베딩된 Bendable 전자모듈을 제작하였다. 전자모듈의 실사용 환경에서의 수명예측을 위한 사전단계로써 고장물리에 기반한 고장모드와 고장메카니즘을 해석하는 것이 최우선 수행되어야 하며, 이를 바탕으로 고장을 유발하는 스트레스 인자를 도출 하였다. 고장도출을 위해 시제품은 JEDEC J-STD-020C의 MSL시험, 고온가압시험, 열충격시험 및 고온저장시험을 각각 수행하였으며, 이로부터 발생된 각각의 고장유형을 분석함으로써 스트레스 인자를 도출하였다. 또한 모아레(Moire) 간섭계를 이용하여 제작된 샘플의 온도변화에 따른 변형해석을 수행하였고, 동시에 Half Symetry Model을 이용한 유한요소해석(FEA)을 수행하여 변형해석 및 스트레스 유발원인을 도출하였다. 이 결과로 부터 고장물리 기반의 고장해석과 Moire 분석 그리고 시뮬레이션 해석 결과를 바탕으로 Bendable 전자모듈의 고장유발 스트레스 인자를 해석할 수 있었다.

• Journal of Welding and Joining
• /
• v.24 no.5
• /
• pp.57-61
• /
• 2006

For the production of functional $TiO_2$-biodegradable plastic (polybutylene succinate:PBS) composite material with photocayalytic activity, we attempted to prepare $TiO_2$ coatings on PBS substrate by HVOF and plasma spraying techniques under various conditions. The microstructures of coatings were characterized with SEM and XRD analysis, and the photocatalytic efficiency of coatings was evaluated by the photo degradation of gaseous acetaldehyde. The effects of primary particle size and spraying parameters on the formation behavior, photocatalytic performance of the coatings have been investigated. The results indicated that for both the HVOF sprayed $P_{200}$ and $P_{30}$ coatings, the high anatase ratio of 100% can be achieved regardless of fuel gas pressure. On the other hand, the HVOF sprayed $P_7$ coating exhibited a largely decreased anatase ratio (from 100% to 49.1%) with increasing the fuel gas pressure, which may be attributed to much higher susceptibility of heat for 7 nm agglomerated powder. HVOF sprayed $P_{200}$ and $P_{30}$ coatings show better performance as compared to that of plasma sprayed $P_{200}$ coatings owing to the higher anatase ratio. However, the HVOF sprayed $P_7$ coatings did not show the photocatalytic activity, which may result from the extremely small reaction surface area to the photocatalytic activity and low anatase ratio.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.9 no.3 s.43
• /
• pp.77-85
• /
• 2005

After the collapse of the World Trade Center in september 11, 2001 and due to the frequent fire-caused damages of buildings during earthquake attacks, social concerns have been increased for the fire proof of the structural members of buildings. Recently, researches have been conducted to improve the fire resistance for building members not by the traditional ways but by utilizing the fire-resisting characteristics of reinforced concrete and structural characteristics of H-steel. In this paper, laboratory tests were conducted in room temperature to investigate the structural performance of the composite beams, which were developed to improve the fire resistance, comprising with concrete incasement between upper and lower flanges of H steel. From the experimental results, the displacement ductility factors of $6\~8$ were obtained. The difference of flexural behavior ol H steel-partial concrete incased composite beams with various composite details seems to be minor. The amount of longitudinal rebars is the most influential factor for the flexural strength of the composite beams. Therefore, if this type of composite beams are selected for designing a building located in moderate seismic lone, identical beam size could be used in several stories of the building.