• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.2
• /
• pp.157-163
• /
• 2020

Recently, fine dust has been known to cause cardiovascular diseases here, raising interest in ways to reduce emissions by efficiently using fuel from cars that cause air pollution. Accordingly, a driving assistance system was developed to save fuel by eco-driving and improve the driver's bad driving habits. The system was developed using raspberry pi, arduino and Android. Using RPM, speed, fuel injection information obtained from OBD-II, and gyro-sensor values, Fuel-Cut is induced to create an optimal inertial driving environment. It also provides various information system such as weather, driving environment, and preventing drowsy driving through GUI and voice recognition functions. It is possible to check driving records and vehicle fault information using Android application and has low overhead for message transmission using MQTT protocol optimized for IoT environment.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.133-140
• /
• 2016

Thermoelectric generator, which is known as using Seebeck effect, have been widely applied in many industrial parts, for instance, from submarine to equipments capable of producing hot or cooling water. Its usefulness was verified in terms of producing electric power using temperature difference and vice versa. Application on thermoelectric generator has been mainly forced on exhaust gas of automotive engine so far. In this study, the possibility was investigated whether electric power could be produced by using cooling water in automotive engine. As the result, it showed that electric power had differences depending on shapes of power auxiliary apparatus and, in this experiment, maximum of electric power was 1.5 voltage.

• Fire Science and Engineering
• /
• v.19 no.3 s.59
• /
• pp.20-27
• /
• 2005

This paper evaluates the fire safety level of eight pump rooms in the nuclear power plant using a fire model, CFAST We estimate the Conditional Core Damage Probability (CCDP) of each room based on the analyzed results of CFAST Eight rooms located on the primary auxiliary building of the nuclear power plant are high pressure safety injection pump room A/B, low pressure safety injection pump room Am. containment sprdy pump room A/B, and motor-driven auxiliary feed water pump room A/B. The upper layer gas temperature of each room is estimated and the integrity of cable is reviewed. Based on the results, the integrity of the cable located at the upper part of compartment is maintained without thermal damage. The Conditional Core Damage Probability Is reduced to half of the old values. Accordingly, the fire safety assessment for eight pump rooms using the fire model will be capable of reducing the uncertainty and to develop a more realistic model.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.15 no.3
• /
• pp.106-112
• /
• 2007

The purpose of this study is to derive the mixing ratio with stable heating value to be used as fuel and secondary fuel by mixing sewage sludge cake, tar, peat moss, and verify the combustion property of produced solid fuel and the applicability of RDF as alternative fuel. Tar shows the highest heating value with 7,000kcal/kg and the heating value of sewage sludge cake and peat moss ranges from 4,000 to 4,500kcal/kg. Also, the solid fuel with length 1.6cm, diameter 1.3cm and weight 2.3g was produced using the heating value of over 6,000kcal/kg and proper mixing ratio (sewage sludge cake: tar: peat moss) from 1 : 4 : 1 to 1 : 7 : 1. Upon the analysis of the RDF applicability of produced solid fuel, the exhaust gas analysis finds that the composition concentration of exhaust gas occurred according to the mixing ratio did not change significantly and the flame lasting time was found to be around 5 minutes, similar to the lasting time of the same mass (2.3g) of general anthracite burned. Therefore, it can be concluded that solid fuel produced in this study can be used as fuel and secondary fuel.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.1
• /
• pp.91-101
• /
• 2017

In this study, we conducted the preliminary research for high speed laser cutting of LED module. In particular, the feasibility of ultra-high speed laser cutting of 100 mm/s which exceeds the cutting speed of conventional dicing saw was examined. For this, copper/ceramic and silicone/ceramic hybrid substrates, which are the components of the LED module, were fabricated, and the surface morphology, surface roughness and flexural strength of the laser-cut samples were investigate and compared with the dicing-cut samples. To investigate optimal laser cutting conditions for hybrid substrates, the effects of various laser cutting conditions on cutting surface characteristics were studied using single ceramic and copper substrate. Optimal laser cutting conditions of the hybrid substrates were the use of Ar assist gas, high laser power and high assist gas pressure. Comparing the cutting surface of the hybrid substrates, the surface characteristics of the laser-cut samples are slightly inferior to those of the dicing-cut samples. The average surface roughness of the laser-cut samples was about $9{\mu}m$, and that of the dicing-cut samples was about $4{\mu}m$. However, considering very low cutting speed (3 mm/s) of the dicing saw, the surface morphology of the laser-cut sample was relatively uniform, and the surface roughness was not much different from that of the dicing-cut sample. The flexural strength of the laser-cut samples was equivalent to or slightly inferior to the flexural strength of dicing-cut samples. However, if the laser processing conditions are sufficiently optimized, the ultra-high speed laser cutting of the LED module will be possible.

• Journal of the Korean Vacuum Society
• /
• v.6 no.3
• /
• pp.200-205
• /
• 1997

Surface of polyethylene film was modified by ion assisted reaction in which ion beam is irradiated on polymer in reactive gas environments. Ion (argon and oxygen) beam energy was 1 keV, doses were varied from $1{\times}10^{14}$ to $1{\times}10^{17}$ inons/ $\textrm{cm}^2$, and amount of blowing oxygen from 0 to 4 sccm(ml/min). Wettability was measured by water contact angle measurement, and the surface functionality was analyzed by x-ray photoelectron spectroscopy. The contact angles of water to polyethylene modified by oxygen ion beam only decrease from 95 to degrees, and surface energy was not changed much. The contact angles remarkably decrease to 28 degrees and surface energy increase to 67 erg/ $\textrm{cm}^2$ when the films were modified by argon ion with various ion doses with blowing oxygen gases near the polyethylene surface. Improvement of wettability and surface energy are mainly due to the new functional group formation such as C-O or C=O, which are known as hydrophilic groups from the XPS analysis, and the assisted reaction is very effective to attach oxygen atoms to form functional groups on C-C bond chains of polyethylene.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.774-780
• /
• 2021

The auxiliary power unit (APU) of a rotorcraft starts the engine during operation/flying. The APU is composed of a gas turbine engine type. The starting principle of the component is that the electric start motor generates the power required for starting by rotating the shaft. In this study, quality improvement was performed by applying an over-running clutch (ORC) between the APU and the starter motor to secure the operability of the starter motor of the APU mounted on the rotorcraft. The starter motor has the main role of starting the APU, but during operation, it is rotated without load by the rotational force of the APU gear shaft, resulting in friction at the brush. This phenomenon causes abrasion of the brush of the starter motor. Consequently, when the APU operation time increases, the brush life decreases, and the operability of the APU is affected. In this study, an ORC that separates the interlocking between the start motor brush abrasion and the APU operation time was applied to improve the operability/durability of the APU starter motor. The effect was verified through a test, and the technical feasibility of the design change was analyzed.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.2
• /
• pp.65-76
• /
• 2015

The Clean Development Mechanism (CDM) is the multi-lateral 'cap and trade' system endorsed by the Kyoto Protocol. CDM allows developed (Annex I) countries to buy CER credits from New and Renewable (NE) projects of non-Annex countries, to meet their carbon reduction requirements. This in effect subsidizes and promotes NE projects in developing countries, ultimately reducing global greenhouse gases (GHG). To be registered as a CDM project, the project must prove 'additionality,' which depends on numerous factors including the adopted technology, baseline methodology, emission reductions, and the project's internal rate of return. This makes it difficult to determine ex ante a project's acceptance as a CDM approved project, and entails sunk costs and even project cancellation to its project stakeholders. Focusing on hydro power projects and employing UNFCCC public data, this research developed a prediction model using logistic regression and CART to determine the likelihood of approval as a CDM project. The AUC for the logistic regression and CART model was 0.7674 and 0.7231 respectively, which proves the model's prediction accuracy. More importantly, results indicate that the emission reduction amount, MW per hour, investment/Emission as crucial variables, whereas the baseline methodology and technology types were insignificant. This demonstrates that at least for hydro power projects, the specific technology is not as important as the amount of emission reductions and relatively small scale projects and investment to carbon reduction ratios.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.1007-1013
• /
• 2013

This study aims to analyze the aerodynamics when the geometry of the turbine rotor is modified. The turbine used in this study is a small engine used in the APU of a helicopter. It is difficult to improve the performance of small engines owing to the structural weakness of the blade tip. Therefore, the improvement of the hub geometry is investigated in many ways. The working fluid of a turbine is a high-temperature and high-pressure gas. The heat transfer rate of the turbine surface should be considered to avoid the destruction of blade owing to the heat load. The SST turbulence model gives an excellent prediction of the aerodynamic behavior and heat transfer characteristics when the numerical simulations are compared with the experimental results. In conclusion, the aerodynamic efficiency is improved when a bulbous design is applied to the leading edge near the hub. The endwall loss is reduced by 15%.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.2
• /
• pp.289-295
• /
• 2017

The International Maritime Organization (IMO) in accordance with the regulations with respect to the combustion gases, such as NOx, SOx generated by the marine engine. The combustion gases must be equipped with a device to reduce emissions from all ships passing through the Baltic SECAs. In Korea, the International Maritime Organization (IMO) and the development of a device for NOx, SOx reduction. Scrubber is used in the ammonia water and the Urea solution in the waste water. The waste water containing ammonium nitrate and ammonium sulfate, react of the NOx and SOx gas. In this study, the recovery of by-product, which contains the waste water was used as an organic solvent extraction method of salting out. Ammonium nitrate and ammonium sulfate, the recovery process. A qualitative analysis of the collected by-product FT-IR analysis. Through the elemental analysis and SEM-EDS, characteristic evaluation was performed with an impurity.