• The Transactions of the Korea Information Processing Society
• /
• v.5 no.4
• /
• pp.1044-1047
• /
• 1998

Non-destructive x-ray inspection system needs image intensifier to obtain the x-ray image. Captured image from image intensifier is distorted because the input plate of image intensifier has a spherical surface. In the research, in order to compensate this image distortion, we created the model of image intensifier and show mathematically that the image distortion was compensated. To show the performance of the proposed method, experiment was performed in real x-ray inspection system.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1542-1551
• /
• 1990

This paper shown how to measure the machining error in diameter of cylindrical workpiece and compensate the measured machining error in NC turning. Machining error is measured by the electric micrometer mounted on the tool post with the NC part program for probe location path analyzed. Correct NC part program for finish turning is automatically generated to compensate the measured machining error. These concepts have been effectively introduced to a newly developed software for error compensation. In turning experiments with the developed error compensation system, machining error was almost within the specified tolerance, which reveals the effectiveness of the developed system.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.647-655
• /
• 2003

This paper studies the observability of calibration system with a constraint movement by a constraint operator. The calibration system with the constraint movement need only simple sensing device to check whether the constraint movements are completed within an established range. However, it yields the concern about the poor parameter observability due to the constraint movements. This paper uses the QR-decomposition to find the optimal calibration configurations maximizing the linear independence of rows of a observation matrix. The number of identifiable parameters are examined by the rank of the observation matrix, which represents the parameter observability. The method is applied to a parallel typed machining center and the calibration results are presented. These results verify that the calibration system with low-cost indicators and simple planar table is accurate as well as reliable.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.91-92
• /
• 2008

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.07a
• /
• pp.224-225
• /
• 2004

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.971-975
• /
• 2009

본 연구에서는 격자강우량과 GIS와 연계한 격자기반의 공간수문자료들을 모형의 입력매개변수로 활용하고, 수계망을 통하여 유역 출구까지 운동파(kinematic wave)이론에 의해 유출량을 물리적으로 추적해 나가는 격자기반의 분포형 강우-유출모형인 K-DRUM(Kwater Distributed RUnoff Model)을 개발하였고, 지표유출량에 가장 큰 영향을 주지만 실제 관측 및 적용이 용이하지 않은 유역의 초기토양함수상태에 대한 자동보정기법을 개발하였다. 개발된 자동보정기법을 이용하여 남강댐유역을 대상으로 적용가능성을 평가하였다. 연구에서 사용한 강우사상은 남강댐 유역에 큰 영향을 준 태풍 루사 (2002년 8월 31일 01시$^{\sim}$9월1일 23시), 태풍 매미 (2003년 9월 12일 01시$^{\sim}$9월13일 23시), 2004년의 대류성강우 (2004년 7월14일 01시$^{\sim}$7월 16일 10시) 및 태풍 에위니아 (2006년 7월 8일 18시$^{\sim}$7월11일 12시)의 총 4개의 사상을 대상으로 하였다. 개발한 유역의 초기토양함수상태 자동보정기법에 의한 유출모의의 적용성을 검토하기 위하여 모의에 사용된 매개변수 중 토지피복도에 의해 결정되는 조도계수와 토양도에 의해 결정되는 유효토심, 흡인수두계수, 공극률 및 투수계수는 4개의 강우사상에서 모두 동일한 조건으로 설정하였고, 유역내 토양 내부 수분함유량 산정을 위한 초기 기저유출량은 검토대상 기간 시점부에서 관측된 유출량으로 설정하였다. 초기토양함수상태 자동보정기법 적용을 통한 유출해석의 정확도는 체적오차 백분율(VER)과 첨두 유량 오차 백분율(QER)을 이용하여 평가하였으며, 이를 통해 본 모형이 유출량에 대한 정확성을 확보하고자 하였다. 본 연구에서 개발된 자동보정 기법을 적용한 결과, 초기토양조건을 설정하는데 있어서 기존의 시행착오법으로 인해 소요되는 시간과 유역내 토양 특성과 지형형상을 고려하지 않는 설정으로 인해 발생될 수 있는 문제점을 해결할 수 있었으며, 유출계산 결과도 유량의 크기와 첨두시간 모두 관측값과 비교적 잘 맞는 것을 확인할 수 있었다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.3
• /
• pp.247-258
• /
• 2004

Two 3-dimensional data processing techniques to predict the fractured zone ahead of a tunnel face by the tunnel seismic survey were proposed so that the geometric formation of the fractured zone could be estimated. The first 3-dimensional data processing technique was developed based on the principle of ellipsoid, The input data needed for the 3D migration can be obtained from the 2-dimensional tunnel seismic prediction (TSP) test where the TSP test should be performed in each sidewall of a tunnel. The second 3-dimensional migration technique that was developed based on the concept of wave travel plane was proposed. This technique can be applied when the TSP is operated with sources in one sidewall of a tunnel while the receivers are installed in both sidewalls. New migration technique was applied to an in-situ tunnelling site. The 3-dimensional migration was performed using measured TSP data and its results were compared with the geological investigation results that were monitored during tunnel construction. This comparison revealed that the proposed migration technique could reconstruct the discontinuity planes reasonably well.

• KIPS Transactions on Software and Data Engineering
• /
• v.8 no.2
• /
• pp.89-96
• /
• 2019

360 degree 3-dimensional lidar sensors and vision cameras are commonly used in the development of autonomous driving techniques for automobile, drone, etc. By the way, existing calibration techniques for obtaining th e external transformation of the lidar and the camera sensors have disadvantages in that special calibration objects are used or the object size is too large. In this paper, we introduce a simple calibration method between two sensors using a spherical object. We calculated the sphere center coordinates using four 3-D points selected by RANSAC of the range data of the sphere. The 2-dimensional coordinates of the object center in the camera image are also detected to calibrate the two sensors. Even when the range data is acquired from various angles, the image of the spherical object always maintains a circular shape. The proposed method results in about 2 pixel reprojection error, and the performance of the proposed technique is analyzed by comparing with the existing methods.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.6
• /
• pp.537-542
• /
• 2015

The measurement of 3D shape is important in inspecting the quality of product. In this paper, we present a 3D shape measurement system of fastener using a camera and a slit laser. Calibration structure with slits is used in the extrinsic calibration of the camera and laser. The pose of the camera and laser is computed under the same world coordinate system in the calibration structure. Reflection of laser light on the metal surface causes many difficulties in the robust detection of them on image. We overcome this difficulty by using color and dynamic programming. Motor stage is used to rotate the fastener to recover the whole 3D shape of the surface of it.

• Korean Journal of Optics and Photonics
• /
• v.7 no.3
• /
• pp.183-190
• /
• 1996

To design three-mirror telescope system (F/8, 120 inch in focal length) for visible and infra-red band imaging, methods for power configuring and correction of the third order aberrations were studied. In the design of the telescope system, a three-mirror system corrected for spherical aberration, coma, and astigmatism was used for infra-red imaging, and the aberrations were corrected by using conic surfaces. For visible imaging, a singlet corrector lens was appended at the front of the focal plane to correct filed curvature. The telescope system has diffraction limited performance for 10 ${\mu}{\textrm}{m}$ in wavelength within 2.4$^{\circ}$ of field-of-view. In the visible band imaging, the rms spot size of the telescope system is less than 25 ${\mu}{\textrm}{m}$ within 3$^{\circ}$ of field-of-view for monochromatic light, and the telescope system satisfies flat field condition for CCD application.