• Journal of the Korea Concrete Institute
• /
• v.26 no.2
• /
• pp.109-116
• /
• 2014

The flexural behavior test of UHPC segmental box girder which has 160 MPa compressive strength and 15.4 m length was carried out. The effect of steel fibers in combination with reinforcing bars on improving the ductile performance of UHPC box girder was evaluated by comparing the flexural behavior of the UHPC segmental box girders made by the two kinds of mixing portion. The test variables are volume fraction of steel fibers and the arrangement of reinforcing bars. The behavior of UHPC box girder BF2 composed of 1% volume fraction of steel fibers and longitudinal reinforcing bars in web and upper flange with stirrup showed the similar ductile behavior with the girder BF1 composed of 2% volume fraction without stirrup in elastic stress region. But BF1 had the better stiffness and showed the more ductile behavior in inelastic stress region. Segmental interfaces of UHPC box girder have not any crack and slide until the final flexural collapse load.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.111-115
• /
• 1994

본 연구에서는 보강 되지 않은 사각단면 박스 구조물, 보강된 사각 단면 박스 구조물, 그리고 보강된 요철형 단면 박스 구좀ㄹ에 대하여 양단 고정(clamped-clamped)과 일단 고정 타단 자유(clamped-free)의 경계 조건에 대해 실험적 진동 해석을 수행 하였으며, 유한요소 code인 ANSYS를 이용하여 유한 요소 해석을 수행하였다. 또한 유한 요소 해석과 실험을 통하여 신뢰성이 검증된 요소를 각 박스 구조물에 적용하여 각 경우에 대한 응력해석을 유한요소법을 이용하여 수행하였다. 또한 각각의 경우에 보강재의 개수 및 단면 형상 변화, 그리고 두께 변화가 진동과 응력에 미치는 민감도를 연구하였다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.5
• /
• pp.197-211
• /
• 2007

The deteriorated PSC Beam bridge is necessary improved reinforcement method. In the study, it is proposed the box reinforcing method which could make the stiffness of the PSC Beam bridges increase more stably through the secondary composition effect of open type PSC Beam bridge's girder which is converted into the consolidation box type and the half panel is formed between the lower flange of the PSC Beam about the deteriorated PSC Beam bridge suffering the capacity decline. In case the proposed reinforcement method combine with the existed external prestressed method, the close analysis depending on the time is conducted by the construction stage because of searching the effect of reinforcement quantitatively. The reinforcement method of the box type which is proposed an efficiency improvement in objective in application case, by a reinforcement method after proposing the whole and bend sectional reinforcement method, against a each reinforcement method evaluated the upward camber which it follows in secondary composite effect and a member stress characteristics. Also, the structural safety of PSC Beam bridge is evaluated quantitatively by examining of rating factor through load carrying capacity evaluation.

• Land and Housing Review
• /
• v.7 no.4
• /
• pp.323-328
• /
• 2016

There are small box opening for inserting of electric lamp box in the slab of apartment. Around this box opening, we normally use the detailing of WWF or plastic ring strengthening to protect cracks induced by shrinkage. The shrinkage amount of slab box around was measured and analysed in order to consider validity of these strengthening methods and to find out economical alternative. Alternative of strengthening methods are normally used strengthening methods in construction companies, which are WWF strengthening, plastic ring strengthening and no strengthening methods. The shrinkage amount was measured using contact guage at the spot of tip attached around the box on slab of small area unit apartment which have small exclusive area below $59m^2$. Measured data shows that there are no big differences between all the 3 strengthening methods and Measure data range is $-264{\mu}{\varepsilon}{\sim}+216{\mu}{\varepsilon}$. Measured shrinkage is on trend slightly increase till 3~5weeks after removal of forms and then decrease. But amount of shrinkage are very low for all the slabs and there are no probabilities of concrete crack by shrinkage.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.3A
• /
• pp.227-234
• /
• 2009

Recently, a knee brace is usually installed in connection between cross-beam and main-girder of steel box-girder bridges. The knee brace is installed as a structural stiffener and mainly aims to relieve stress at joints and to prevent main-girder from lateral deformation. However, research on the knee brace is insufficient to obviously evaluate the necessity. The stiffened effect of knee brace is determined by using finite element analyses. Stress distribution, stress level of members and deflection of the cross-beam are evaluated by parametric FE analysis for the installation of knee brace and the depth ratio of cross-beam/steel box girder. It is seen from comparison of numerical analysis results that the knee brace installed in cross-beam of steel boxgirders bridges is not efficient as a structural stiffener with respect to stress relief and stiffened effect.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.29 no.5
• /
• pp.397-403
• /
• 2016

During the rapid economic growth in Korea since the 1970s, many underground facilities were constructed such as under passes and railways. Seismic design has been mandated in 1988, but the structures built before 1988 were not reflected on the seismic design. Accordingly, these underground structures require effective seismic reinforcing methods to ensure safety when the earthquake happens. By these reasons, in this study, using the proposed pre-flexed members, RC box structure was analyzed for seismic reinforcement of the corner. This method is based on a principle that enlarging the resistance against the external force by installing the pre-flexed member to the box structure corner. To evaluate validity, a newly developed member with CornerSafe was compared with traditional type reinforcement using experiments and finite element analysis. In finite element mode, nonlinearity of steel was modeled based on J2 plasticity model and concrete was based on CEB FIP MODEL CODE 1990. Also, composite ratios of box and pre-flexed member were computed for design application. The reinforcement and box structure were analyzed under the bond condition completely attached by the tie, and the results of experiment and finite element analysis were same in the force-displacement curve.

• Geotechnical Engineering
• /
• v.38 no.5
• /
• pp.31-37
• /
• 2022

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.11
• /
• pp.5-18
• /
• 2010

In this paper, a 3-dimensional stiffened plate model for soil-metal box structures is proposed. 3-dimensional stiffened plate model is enable to model corrugated steel plates of soil metal box culverts considering section modulus and section properties of longitudinal and horizontal direction from a corrugated steel plate. Loading conditions which causes maximum displacement and maximum moment according to the step construction stages(a back filling to the top of the plate, a back filling to the maximum depth of cover, and loading of live loads) was applied and the behaviors of the soil metal box culverts was analyzed. Analysis results of 3-dimensional stiffened model were compared with those of 2-dimensional model, 3-dimensional equivalent plate model and 3-dimensional corrugated plate model. As results, the behaviors of 2-dimensional model and 3 dimensional equivalent model are different from 3-dimensional corrugated plate model but the result of 3-dimensional stiffened model has good agreement with that of 3-dimensional corrugated plate model.

• Computational Structural Engineering
• /
• v.11 no.3
• /
• pp.173-185
• /
• 1998

본 연구에서는 자동차엔진 및 트랜스미션 성능시험을 위한 다이나모 베드구조물을 분석하고 설계하였다. 해석상에 고려된 베드구조물은 Ⅰ형강 구조물, 보강된 박스구조물 그리고 블록구조물로 제작되었으며, 시험을 위한 엔진 및 트랜스미션은 베드상판에 장착된다. 엔진구동시 회전에 의한 진동이 발생된다. 공진을 피하기 위해 베드구조는 충분한 구조적 일체성을 가져야 한다. 본 연구에서는 베드 구조물의 응력, 변위 그리고 자유진동해석이 ANSYS Code를 이용한 유한요소해석이 수행되었다. Ⅰ형강 구조형 베드 구조물에서 최대 응력은 23.2MPa에서 90.3MPa까지 나타났으며, 최대 처짐은 0.25㎜에서 0.92㎜까지 나타났다. 박스 구조형 베드 구조물에서 최대 응력은 0.028MPa에서 0.259MPa까지 나타났으며, 최대 처짐은 0.031㎜에서 0.413㎜까지 나타났다. 그리고 박스구조형 베드 구조물에서 최대 처짐은 0.92MPa에서 2.15MPa까지 나타났으며, 최대 처짐은 1.1㎜에서 2.7㎜까지 나타났다. 모든 구조물이 응력과 처짐 값에서 매우 안정적인 범위 내에서 발생됨을 볼 수 있었다. 구조진동해석에서 Ⅰ형강 베드구조물의 고유진동수는 112.03㎐에서 141.66㎐까지의 범위에 발생되었다. 박스 구조형 베드구조물에서의 고유진동수는 396.93㎐에서 755.11㎐까지의 범위에서 발생되었다. 마지막으로 블록구조형 베드구조물에서는 266.51㎐에서 244.67㎐까지의 고유진동수를 찾을 수 있었다. 모든 구조물에서 베드구조물의 무게증가에 따른 기본진동수는 증가된다. 베드시스템의 지지기초시스템은 2자유도계 시스템으로 설계되었으며, 다양한 질량변화 및 스프링상수 변화에 따른 진동해석을 수행하였다. 질량비가 증가될수록 고유진동수는 크게 감소되며, 스프링상수가 증가될수록 고유진동수는 감소된다.

• Geotechnical Engineering
• /
• v.38 no.1
• /
• pp.26-33
• /
• 2022