• Proceedings of the Korea Concrete Institute Conference
• /
• 1990.04a
• /
• pp.78-83
• /
• 1990

The current analytical techniques for R/C elements under severe dynamic repeated loads, like earthquake or impact, has two major problems; one is that the effects of strain rate are not considered and the other one is the current model was developed based on flexural behavior only. Thus, this study develops a computer software that can idealize the flexural and shear behavior of R/C elements using several parameters and also can consider the effects of strain rate. The analytical results using the developed analytical technique were compared with several experimental results and were generally satisfied.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1995.05a
• /
• pp.3-8
• /
• 1995

추진기관 적용에 따른 복합재연소관의 일반적 사항들을 논하였다. 추진기관의 효율에 주요인자인 경량화에 있어서 복합재 연소관의 무게가 철금속 연소관에 비해 약 50%의 감소효과가 있으며 단가의 측면에서도 부가가치가 있는 것으로 평가된다. 그러나 추진기관 체계적(추진제 공정 및 구조안정성) 관점에서 추진제 내면변형율(Inner Bore Strain)의 증가, 제작공차, 공정의 재현성, EPDM의 접착기밀성 및 외부습도 유입 문제 등의 앞으로 해결되어야 할 사항들이 제시되었다.

• The Korean Journal of Rheology
• /
• v.9 no.3
• /
• pp.124-131
• /
• 1997

스테인레스 강(SUS 316L) 분말과 왁스계 결합제를 혼합하여 제조한 분말사출재의 유변학적 특성을 낮은 전단율에서 측정하기 위해 동심원반식 점성측정기를 이용하여 실험을 실시하였다. 측정기 벽면에서 발생하는 벽면 슬립(Slip)을 확인하고 벽면 슬립을 보정하기 위하여 두가지의 원반 간격에서 측정된 실험 자료를 이용하여 벽면 슬립을 보정하는 방법을 채택하였다. 실험 중, 측정 전단율범위를 제한하는 Thixotropy 현상을 발견학고 이에대한 원인분석을 위한 실험을 진행한 결과 과도한 전단응력에 의해서 분말사출재로부터 분리되어 나온 슬립층이 내부로 빠르게 흡수되어 들어가지 못하고 잔류하면서 Thixotropy 현상을 발 생시키는 것으로 판단되었다. Thixotropy 현상이 발생하지 않는 범위를 조사한후, 제한된 범위내에서 분말사출재의 유변학적 특성을 측정하였다. 측정된 자료는 항복응력을 지니는 유체의 특성을 표현하는 Bingham 식의 변형식에 잘 근사 되었으며, 슬립속도를 실험결과로 부터 계산한 결과 전단응력에 따라 선형적인 관계를 가지고 있는 점과 항복응력의 존재를 정성적으로 보여주는 결과를 얻었다.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.2
• /
• pp.87-97
• /
• 2008

Behaviors of cemented engineered soils, composed of rigid sand particle and soft rubber particle, are investigated under $K_o$ condition. The uncemented and cemented specimens are prepared with various sand volume fractions to estimate the effect of the cementation in mixtures. The vertical deformation and elastic wave velocities with vertical stress are measured. The bender elements and PZT sensors are used to measure elastic wave velocities. After cementation, the slope of vertical strain shows bilinear and is similar to that of uncemented specimen after decementation. Normalized vertical strains can be divided into capillary force, cementation, and decementation region. The first deflection of the shear wave in near field matches the first arrival of the primary wave. The elastic wave velocities dramatically increase due to cementation hardening under the fixed vertical stress, and are almost identical with additional stress. After decementation, the elastic wave velocities increase with increase in the vertical stress. The effect of cementation hinders the typical rubber-like, sand-like, and transition behaviors observed in uncemented specimens. Different mechanism can be expected in decementation of the rigid-soft particle mixtures due to the sand fraction. a shape change of individual particles in low sand fraction specimens; a fabric change between particles in high sand fraction specimens. This study suggests that behaviors of cemented engineered soils, composed of rigid-soft particles, are distinguished due to the cementation and decementation from those of uncemented specimens.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.117-122
• /
• 2005

Titanium alloy has widely been used as material for glasses frame parts because it has high specific strength. It is also light and harmless to human body. However, we have little design data about the mechanical properties such as the creep behaviors of the alloy. Therefore, in this study, creep tests under four constant stress conditions have been conducted with four different temperature conditions. A series of creep tests had been performed to get the basic design data and life prediction of titanium products and we have gotten the following results. First, the stress exponents decrease as the test temperatures increased. Secondly, the creep activation energy gradually decrease as the stresses became bigger. Thirdly, the constant of Larson-Miller parameter on this alloy was estimated as about 2.5. Finally, the fractographs at the creep rupture showed the ductile fracture due to the intergranullar rupture and some dimples.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.4
• /
• pp.452-462
• /
• 1985

The axisymmetric forward extrusion is analyzed by using the rigid-plastic finite element formulation. The distribution of stresses and strains as well as the deformation pattern in solid extrusion is very important for the improvement of product quality. The initial velocity field is determined by assuming the material as a Newtonian fluid through an arbitrarily shaped axisymmetric die. The workhardening effect and the friction of the die-material interface are considered in the formulation. Some reduction of area and die shapes(conical and biquadratic-curved) are chosen for computation. Experiments are carried out for steel alloy(SCM4) specimens using conical and curved dies. It is found that experimental observation is in good agreement with FEM results. The strain distribution is curved(biquadratic) dies is shown to be more uniform than in conical dies at the same reduction of area.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.153-158
• /
• 2005

Titanium alloy has widely been used as material for automotive parts because it has high specific strength. It is also light and harmless to human body. But, we have little design data about the creep behaviors of the alloy. Therefore, in this study, creep tests under four constant stress conditions have been conducted with low different temperature conditions. A series of creep tests had been performed to get the basic design data and life prediction of titanium products and we have gotten the fallowing results. First, the stress exponents decrease as the test temperatures increased. Secondly, the creep activation energy gradually decrease as the stresses became bigger. Thirdly, the constant of Larson-Miller parameter on this alloy was estimated as about 7.5. And for the last, the fractographs at the creep rupture showed the ductile fracture due to the intergranullar rupture.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.2 s.257
• /
• pp.174-181
• /
• 2007

This paper is concerned with the thermo-mechanical behavior of steel sheet for an auto-body including temperature dependent strain rate sensitivity. In order to identify the temperature-dependent strain rate sensitivity of SPRC35R, SPRC45E and TRIP60, uniaxial tensile tests are performed with the variation of the strain rates from 0.001/sec to 200/sec and the variation of environmental temperatures from $-40^{\circ}C$ to $200^{\circ}C$. The thermo-mechanical response at the quasi-static state is obtained from the static tensile test and that at the intermediate strain rate is obtained from the high speed tensile test. Experimental results show that the variation of the flow stress and fracture elongation becomes sensitive to the temperature as the strain rate increases. It is observed that the dynamic strain aging occurs with TRIP60 at the temperature above $150^{\circ}C$. Results also indicate that the flow stress and tincture elongation of SPRC35R are more dependent on the changes of strain rates and temperature than those of SPRC45E and TRIP60.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.456-461
• /
• 2004

The dynamic behavior of sheet metals must be examined to ensure the impact characteristics of auto-body by a finite element method. An appropriate experimental method has to be developed to acquire the material properties at the intermediate strain rate which is under 500/s in the crash analysis of auto-body. In this paper, tensile tests of various different steel sheets for an auto-body were performed to obtain the dynamic material properties with respect to the strain rate which is ranged from 0.003/sec to 200/sec. A high speed material testing machine was made for tension tests at the intermediate strain rate and the dimensions of specimens that can provide the reasonable results were determined by the finite element analysis. Stress-strain curves were obtained for each steel sheet from the dynamic tensile test and used to deduce the relationship of the yield stress and the elongation to the strain rate. These results are significant not only in the crashworthiness evaluation under car crash but also in the high speed metal forming.

• Computational Structural Engineering
• /
• v.3 no.3
• /
• pp.53-54
• /
• 1990

응력 변형율의 관계가 시간에 대한 미분의 형태로 나타나는 비선형 탄소성 혹은 점탄소성 재질을 갖는 구조물이나 지만의 거동 문제를 유한요소법 등의 방법을 이용하여 해결하려고 하는 경우 주어진 외력에 의한 새로운 응력이나 응력 강화 현상을 표현하는 여러 재료 상수값들을 구하기 위해서는 적분을 요하게 되며 일반적으로 수치해석적 방법에 의해 수행된다. 이러한 수치해석적 적분방법은 보다 정확한 결과를 얻기 위하여 알고리즘 자체의 정확성과 안정성이 요구된다. 정확성은 수치해석적 적분방법이 적용될 수 있는 step size에 관계없이 거의 동일한 결과치를 얻을 수 있느냐 하는 것을 말하고 안정성은 큰 step size에서도 수렴된 결과치를 얻을 수 있느냐 하는 것을 의미한다. 그 뿐만 아니라 비교적 복잡하고도 그 대상영역이 큰 문제를 해석하고자 할 때는 수렴속도 또한 빠른 해석방법이 바람직하게 된다. 따라서 본 기사에서는 여러가지 가능한 수치해석 적분 방법을 소개하고 그들의 장단점을 논하고자 한다.