• 대한기계학회논문집A
• /
• 제21권5호
• /
• pp.842-849
• /
• 1997

The aim of this study is an investigation of the interaction of two micro hole defects affecting fatigue crack initation life and propagation behavior. The locatio of two micro hole defects was considered as an angle of alignment and the distance between the centers of two micro hole defects. The fatigue cracking behavior is experimented under bending. When micro defects are located close to each other, the fatigue crack initiation lives are varied with their relative locations. In the experiments, the area of local plastic strain strongly played a role in the fatigue crack initiation lives. Therefore we introduce a parameter which contains the plastic deformation area at stress concentrations and propose a fatigue crack initiation life prediction curve. In addition, the directions and propagation rates of fatigue cracks initiated at two micro hole defects are studied experimentally.

• 한국지진공학회논문집
• /
• 제5권6호
• /
• pp.1-10
• /
• 2001

본 연구에서는 수평전단시험을 통하여 LRB(lead-rubber hearing)의 동적 특성을 분석하였다. 10ton 및 200ton 용량의 LRB를 이용하여 수평전단시험을 수행한 결과 LRB의 동적 특성은 수평하중의 재하속도, 연직하중의 크기 및 전단변형률 등에 따라 크게 달라지는 것으로 나타났다. 세장비가 큰 면진장치에 과도한 변형을 가할 경우 내부 납심에 소성한지가 발생되어 납심이 파괴되는 것으로 나타났다. 따라서 면진구조물의 설계 및 해석 시에는 지진응답과 재하하중의 크기에 따라서 달라지는 LRB의 기계적 특성치를 적용하여 안전한 설계가 이루어질 수 있도록 하여야 한다.

• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1201-1207
• /
• 2010

본 연구에서는 마이크로 시험편에 대하여 하중제어 인장-인장의 피로시험이 가능한 피로시험기를 개발하였다. 전자기식 액추에이터를 이용하였으며, 이 시험기를 이용하여 인장시험 뿐만 아니라 넓은 주파수 영역에서의 피로시험이 가능하다. 또한 피로시험중에도 고해상도로 마이크로 시험편의 되풀이 변형률을 측정할 수 있는 간섭변위계를 사용하였다. 피로시험기와 변위계는 안정적이고 그 응답속도도 매우 빨라서, 피로시험중에도 연속적으로 변위를 측정할 수 있다.

• 한국해양공학회지
• /
• 제14권1호
• /
• pp.23-28
• /
• 2000

The fatigue crack growth behavior of the cold-rolled STS 304 steel developed for membrane material of LNG storage tank was examined experimentally at 293K, 153K and 111K. The fatigue crack growth rate(do/dN) tends to increase as the stress ratio (R) increases over the testing temperature when compared at the same stress intensity factor range($\Delta$K). The effect of R on do/dN is more explicit at low temperatures than at room temperature. The resistance of fatigue crack growth at low temperatures is higher compared with that at room temperature which is attributed to the extent of strain-induced martensitic transformation at the crack tip. The temperature dependence of fatigue crack growth resistance is gradually vanished with an increase in $\Delta$K which correlates with a decreasing fracture toughness with decreasing temperature. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and low temperature are mainly explained by the crack closure and the strengthening due to the martensitic transformation.

• 한국전기전자재료학회논문지
• /
• 제22권1호
• /
• pp.67-73
• /
• 2009

The stress-strain behavior and its effects on the crack initiation and growth of ITO film on PET substrate with a sheet resistance of 45 ohms/sq were investigated. Electrical resistance increased gradually at the strain of 0.7% in the elastic to plastic transition region of the stress strain curves. Numerous cracks were observed after 1% strain and the increase of the resistance can be linked to the cracking of ITO thin films. The onset strain for the increase of resistance increased with increasing strain rate, suggesting the crack initiation is dependent on the strain rate. Upon loading, the initial cracks perpendicular to the tensile axis were observed and propagated the whole sample width with increasing strain. The spacing between horizontal cracks is thought to be determined by the fracture strength and the interfacial strength between ITO and PET. The crack density increased with increasing strain. The spacing between horizontal cracks (perpendicular to the stress axis) increased with decreasing strain rate, The increase of crack density with decreasing strain rate can be attributed to the higher fraction of the plastic strain to the total strain at a given total strain. As the strain increased over 5% strain, cracks parallel to the stress axis were developed and increased in number with strain, accompanied by drastic increases of resistance.

• 한국안전학회지
• /
• 제27권6호
• /
• pp.7-13
• /
• 2012

A lack of study on the dynamic tensile strengths of Sn-based solder joints at high strain rates was the motivation for the present study. A modified miniature Charpy impact testing machine instrumented with an impact sensor was built to quantitatively evaluate the dynamic impact strength of a solder joint under tensile impact loading. This study evaluated the tensile strength of lead-free solder ball joints at strain rates from $1.8{\times}10^3s^{-1}$ and $8.5{\times}10^3s^{-1}$. The maximum tensile strength of the solder ball joint decreases as the load speed increases in the testing range. This tensile strength represented that of the interface because of the interfacial fracture site. The tensile strengths of solder joints between Sn-3.0Ag-0.5Cu and copper substrate were between 21.7 MPa and 8.6 MPa in the high strain range.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.378-382
• /
• 2008

Since the sheet metal forming of Mg alloy is perform at elevated temperature, the effect of strain rates related with the forming temperature and forming speed and R-value is very important factor for formability and forming limits and deep drawing. It is investigated that the effect of material properties such as various temperature, forming speed and strain rates on formability and R-value of Mg alloy sheet in round cup deep drawing. Therefore, the investigation for process variables is necessary to improve formability and forming limits and deep drawing. Also, the effects of strain rate and drawbility were studied by the experiment. The temperature, forming speed, and strain rates and R-value are investigated. Forming of Mg alloy takes consider into temperature, proper forming speed and strain-rate and R-value the formed parts were good without defects for forming limits and deep drawing.

• 한국전산구조공학회논문집
• /
• 제34권2호
• /
• pp.85-91
• /
• 2021

본 연구에서는 섬유보강콘크리트(SFRC) 구조물의 수치해석을 위한 K&C모델의 보정기법을 소개하였다. SFRC 1축 및 3축 압축강도 실험결과를 기반으로 보정을 수행하였으며, 단일요소 해석결과를 실험결과와 비교함으로써 보정 기법의 검증을 수행하였다. 또한, 변형률 속도의 영향을 반형하기 위해 동적증가계수(DIF)를 고려하여 SFRC 구조물의 발사체 관통해석을 수행함으로써 보정기법의 적용 가능성을 확인하였다.

• 한국자기학회지
• /
• 제3권3호
• /
• pp.201-207
• /
• 1993

$Pr_{15}Fe_{77}B_{8}$ 조성의 합금을 Ar분위기에서 유도용해로를 이용하여 주조하 였다. 이 합금을 석영관에 넣어 고주파 유도로를 이용하여 용해한 후 0.6 nm의 분출구를 통해 회전하는 Cu wheel위에 분사하여 비본형태로 제조하였다. 이 리본을 열간변형하여 결정방향성을 주었는데 이를 위 해 먼저 $680^{\circ}C$에서 $21.8\;kg/mm^{2}$의 압력으로 hot-press하여 92%의 densification을 갖는 시편을 얻을 수 있었다. 이 시편을 다양한 조건하에서 die-upset을 행하였다. 변형율이 높을 수록 $_{i}H_{c}$는 저하되었으나, $B_{r}$은 현저하게 증가되었으며, XRD 분석 결과(006)면에서의 회절강도가 증가되었다. 따라서 압축방향으로 자화용이축이 형성되었음을 알 수 있었다. Die-upset시의 변형속도가 빠를 수록 $_{i}H_{c}$는 증가되었으나, $B_{r}$은 감소되었다. 가공온도에 따른 $B_{r}$의 변화는 $750^{\circ}C$ 까지 상승한 후 감소되었다. 이 조성의 $4{\pi}M_{s}$는 11.8 kG였고 $750^{\circ}C$에서 0.05 mm/sec의 가공속도로 변형률 0.8로 die-upset한 경우에는 $B_{r}$이 11.0 kG로 우수한 자기이방성을 가지고 있으나, die-upset후에 $_{i}H_{c}$가 낮은 문제점이 있다.